Do-it-yourself VAZ 2114 spoiler repair

How to install a spoiler on 2114, following technology

To improve the aerodynamic performance and appearance of the car, and save fuel, special devices are used - spoilers. There are, of course, car enthusiasts who are indifferent to them. However, many car owners are interested in the question of how to install a spoiler on a 2114, because it was not included in the package, and for some it needs to be repaired or reinstalled.

Spoiler for VAZ 2114 - how to choose, install, replace and repair

A little about the functions of the part

The wing is one of the elements that affects the aerodynamics of the car. It is responsible for organizing the correct direction of the air flow coming from the trunk of the car or its roof.

Aerodynamic drag

The drag coefficient actually decreases after installing a wing on a car, and this fact has been proven. The percentage of this coefficient depends only on the shape and size of the installed wing.

Withdrawal procedure

Remove the trunk door trim.
Disconnect the wires of the additional brake light.

It is possible that on cars of early years of production you will have to unscrew the nut securing the ground wire of the additional brake signal from the stud securing the trunk door lock.

3. Using a 10mm socket wrench, tighten the 2 spoiler mounting nuts on the right.

4. We also unscrew the 2 nuts on the left.

5. Remove the spoiler from the car.

On cars of early years of production, the spoiler was attached differently. On them, in the door cavity there were only 2 fastening nuts. From the sides, the spoiler was held on the trunk door using 2 pressure plates. Therefore, to remove the spoiler, you first need to unscrew the plates and then the 2 nuts in the door cavity.

6. Install the spoiler on the car in the reverse order.

How to replace a spoiler on a VAZ 2113, VAZ 2114?

Removal: 1) At the very beginning of the operation, open the trunk of the car and then take a screwdriver in your hands and use it to pry off about 10 pistons that secure the trunk lid trim and after prying, remove the lid from the door as shown in the small picture just below:

2) Then, along the entire trunk lid, find two nuts (One of the nuts is shown in the photo below) that secure the pressure plates (One of the plates is indicated by an arrow) and then completely unscrew both nuts and, after unscrewing, remove the pressure plates that are secured with these same nuts.

3) After the nuts that secure the plates are unscrewed, take a wrench in your hands and use it to completely unscrew the nut that secures the trunk lock (This nut is indicated by an arrow) and under this nut you will find a wire that goes to ground, so thanks to this When braking, the wire turns on an additional brake light, which is located in the spoiler, you will need to remove this wire from the stud and then either tighten the nut back (This is the case if you are no longer going to install a new spoiler) or simply leave the nut loose and When installing a new spoiler, put the wire that will go from it to this very stud and then tighten the whole thing with a nut.

Note! In all cases when you work with electronics, it is recommended to de-energize the battery to prevent a short circuit from water getting on the wiring, for example, so before you start unscrewing this nut, we recommend that you remove the negative terminal from the battery! (For information on how to remove the terminal, see the article: “Replacing the battery,” point 1)

4) Now look for the positive wire thanks to which the brake light works when braking, which is built into the rear spoiler, so the positive wire is made in the form of a block of wires, so when you find the block of wires and the connector with which it is connected together, grab them with both hands and disconnect from each other.

5) And at the end of the operation, using a wrench and a socket head, or using just a wrench or a spanner, completely unscrew the two outermost side bolts as shown in the figure below, which secure the spoiler in the side part, and after they are turned out, remove the clamping brackets that will secure these bolts (Removing the clamping bracket in the photo below is shown using the example of the left bolt, that is, in the main photo the bolt is unscrewed, and the small photo shows how the bolt is removed together with the clamping bracket).

Installation: The new spoiler is installed in its place in the reverse order of removal; when installing, be sure to put on all the wires and connect the connector and wire block together, otherwise the brake light will not work when braking.

Note! When installing a new spoiler, we recommend that you lubricate with some anti-corrosion substance, for example with Movili or with anti-corrosion Primer, all those parts where the spoiler will fit when you install it in place.

What does it look like?

Large spoilers affect the aerodynamic performance of the car. Thanks to these devices, the car is able to reach high speeds while driving and consume fuel more economically. Motorists often use rear and front spoilers.

The choice depends on the driver's preference and expected result. It is necessary to pay attention to the material from which this part is made. Often, car enthusiasts install a decorative rear spoiler, which only helps to change the appearance, but does not affect the speed and other parameters of the car in any way.

Tuning VAZ 2114

To properly fix the spoiler, it is recommended to adhere to the following sequence of work:

The length and width of the trunk are measured.
Make marks with a marker in those places where there will be a fastening connection between the device and the car body.
After drilling the holes, remove the chips and paint the edges to avoid rust in the future.
Install the brackets into the hole and secure the fixture using nuts and bolts.
If using a decorative option, it is perfectly acceptable to use an adhesive instead of drilling.

Recommendations

Correct installation of a high-quality spoiler on a VAZ 2114 will help reduce vehicle air resistance and fuel consumption. If the fixation of the device is not done correctly, then this will not improve the performance of the car, but, on the contrary, will reduce its aerodynamics.

To prevent this from happening, you should familiarize yourself with the recommendations of experts on how to install a spoiler with your own hands:

If there is no space for installing the device, then there is no need to drill the body. An adhesive sealant is quite suitable. A prerequisite is complete solidification of the substance within 3-4 days;
to prevent rust, it is recommended to lubricate the joints between the device and the body with machine oil or wax;

Installing a spoiler on a VAZ 2114

It is better to paint before installation. It is desirable that the color matches the main color of the car or contrasts;
At the fastening points, if desired, use not a polypropylene seal, but an ordinary piece of vacuum rubber.

Drivers who have doubts about the final result turn to specialized salons, where experienced specialists will do this work quite quickly and efficiently.

Author: Ekaterina

Chassis

Improving the chassis of a car will not change its appearance in any way, but will significantly improve its dynamic properties and behavior on the road. It is divided into 2 types:

The first improves the driving characteristics of the car, allowing it to move quickly along city streets, the second reduces fuel consumption. The main systems subject to tuning are the engine and chassis.

Suspension

Tuning the VAZ 2114 suspension includes both calibration of the entire system, wheel alignment of the car, and modernization of individual parts:

replacing springs;
shock absorber tuning;
installation of anti-roll bar.

These details will increase driving comfort and also improve the car’s behavior on the road: the car will rock less and will not roll during sharp turns.

Engine

Tuning a VAZ 2113, 2114 or 2115 engine is a rather complicated, but feasible undertaking. To slightly increase the power of the machine you need:

reflashing the control unit;
increasing the cylinder diameter by boring.

To achieve a more significant effect, it is necessary to change the cylinder block that distributes the gas. Taken together, these changes are considered safe; they will help increase engine power by up to a third.

Among the more effective, but risky methods is installing a turbine and replacing the crankshaft with a new one, with an increased piston stroke. This will reduce the operating time of the car, but can lead to its rapid breakdown.

Visor “Voron Glass” for the rear window of VAZ 2108, 2109, 2114 – 500 rub.
Lip spoiler, unpainted – 590 RUR.
Rear window deflector “M-Version” (2109-2114), tuning – 800 rub.
Trade Auto, 21140-6301116-00 (PVC trunk spoiler without a lamp, for painting) – RUB 1,107.
AvtoVAZ, rear door spoiler in Cosmos 665 color (under the canopy) – RUB 1,900.

In addition to products, the installation of which does not require changes to the design of the car , and also does not raise suspicion during a technical inspection, it is worth noting tuned spoilers at an affordable price. These include:

Fast and Furious (on metal stands with four mounting points) – 2,200 rubles.
V-Max (fiberglass in transport primer for grinding) – RUB 3,350.
Rs-2 (fiberglass and polyester resin) – RUB 1,500.
Impulse “AVR” (reinforced with mortgages, weight is 3.9 kg) – 2,100 rubles.
Ferrari Ango 2114 (width at the mounting point 125 mm, extending beyond the standard holes) – RUB 2,740.

When installing tuned spoilers on the rear door of a VAZ 2114, a leak may occur in the trunk, which will negatively affect the operation of the rear lighting equipment.

Examples of prices for original and tuned spoilers

Visor “Voron Glass” for the rear window of VAZ 2108, 2109, 2114 – 500 rub.
Lip spoiler, unpainted – 590 RUR.
Rear window deflector “M-Version” (2109-2114), tuning – 800 rub.
Trade Auto, 21140-6301116-00 (PVC trunk spoiler without a lamp, for painting) – RUB 1,107.
AvtoVAZ, rear door spoiler in Cosmos 665 color (under the canopy) – RUB 1,900.

In addition to products, the installation of which does not require changes to the design of the car, and also does not raise suspicion during a technical inspection, it is worth noting tuned spoilers at an affordable price. These include:

Fast and Furious (on metal stands with four mounting points) – 2,200 rubles.
V-Max (fiberglass in transport primer for grinding) – RUB 3,350.
Rs-2 (fiberglass and polyester resin) – RUB 1,500.
Impulse “AVR” (reinforced with mortgages, weight is 3.9 kg) – 2,100 rubles.
Ferrari Ango 2114 (width at the mounting point 125 mm, extending beyond the standard holes) – RUB 2,740.

When installing tuned spoilers on the rear door of a VAZ 2114, a leak may occur in the trunk, which will negatively affect the operation of the rear lighting equipment.

Repair of spoiler VAZ 2114

rust in places where it is attached to the trunk;
an attempt to open the trunk using the spoiler as a lever;
Damage or tearing out of fastenings to the trunk.

Removing rust

The rusted areas are cleaned with sandpaper, treated with a rust converter, washed and painted.

During repairs, special plugs are installed in the technological openings of the trunk. Sometimes these holes are simply temporarily sealed with regular tape.

Repair work

Do-it-yourself spoiler repair is often accompanied by filling its interior with polyurethane foam. This is done to give the structure additional rigidity and strength. Before filling with foam, the spoiler is wrapped with cling film and tape to protect it from swelling.

To maintain the possibility of replacing the brake light and wires, the wires are passed through the corrugation and then the internal cavity is filled with foam. In the areas of attachment to the trunk, cones are cut out of the foam into which bolts are inserted. Then the cones are filled with epoxy or buried with superglue.

Since the plastic is the thinnest at the points where it is attached to the body, the spoiler protrusions for fastening are often reinforced by filling them with epoxy resin, and long bolts with washers and nuts are used as fasteners. In this case, a strong trapezoidal base is obtained in which the mounting bolts are located.

After the bolts are placed in the spoiler protrusions, they are filled with plastic shavings dissolved in acetone with added superglue for additional strength. Sometimes the bolts are buried with molten plastic. The plastic is melted with a lighter directly above the bolt.

Then, according to the instructions, prepare the epoxy resin for pouring, mixing it with the hardener. There are options for filling through a syringe; in this case, an additional technological hole is drilled. Epoxy is poured into the additional hole, and plugs are placed on the bolts and secured with superglue.

Epoxy resin gets very hot when interacting with the hardener. If you protected the spoiler from contamination by wrapping it in cling film, the film may melt to its body. It is necessary to provide for the possibility of ventilation of overheated areas. Sometimes, for strengthening, the entire internal cavity is filled with epoxy resin, and not just vulnerable fastening points. After pouring, the protruding excess is cut off and sanded.

If areas at the fastening points are broken, a suitable piece of plastic is attached to the bolts on the sides to the remaining plastic on the bolts.

Repair stages briefly:

Installation of corrugation.
Film protection.
Foaming (in some cases).
Fixing the bolts with superglue.
Drilling technological holes.
Fixing bolts with plastic (in some cases).
Pouring epoxy.

Spoiler for VAZ 2114 - we do it ourselves

The body kit elements are undoubtedly pleasing to the eye and perform all the functions assigned to them by the developers of “hot” hatchbacks from major manufacturers. For several years now, the fashion for body kit tuning components has been observed among Russian car enthusiasts. One example is the spoiler on the VAZ 2114, which, when properly executed, creates the proper aerodynamic effect.

Among the models of spoilers presented on our market, you can choose the appropriate option for any car. Although in most cases, factory wings are still subject to modifications. In this regard, the question arises: should I make a spoiler myself? After all, this is both money saved and a form “to your taste.”

Materials for the spoiler

You should immediately discard blanks made from foam sealant. Usually this is too expensive, because it is quite difficult to calculate how many cans of material will be needed for a VAZ spoiler in a particular case.

Preferable polystyrene foam: a sheet of polystyrene foam 5 cm thick and an area of 1x1 m. You should also buy epoxy glue, but not in syringes, but in a paper box. If there is no fiberglass, then you can use unnecessary “silk” shirts. At the end, the wing for the VAZ 2114 will need to be sanded, painted and varnished - accordingly, you will need sanding tools, paint and varnish (preferably in spray cans).

Installation of the lip

Along with the spoiler, many install the so-called lip, which is easier to manufacture. It is necessary to remove the VAZ 2114 bumper, turn it over, glue a blank from foam plastic and give it the desired shape. Then wrap it in polyethylene bags. Wrap it in several layers with ordinary women's tights (or similar material) and coat the base with epoxy. When the layers of tights are dry, remove the blank from the lip. The final polymerization of the epoxy will be completed in a few days.

THIS IS INTERESTING: Replacing the crankshaft of a VAZ 2110

If the glued lip is not strong enough, then you should also take a shirt and glue it from the inside of the workpiece in two layers. For greater strength, you can purchase a reinforcing mesh and glue it with it. This is followed by sanding with primer and painting.

Installation of the VAZ 2114 wing

Now we make the spoiler mounts. You need to cut 1.5 mm plates from a steel sheet and drill 3 mm holes in 2 cm increments. For better fixation and reduced weight, the plates can be bent into an L shape, and two 5 mm nuts can be welded to the base. Glue them into foam blanks, cover the spoiler blade with layers of fabric and assemble everything.

As practice shows, it is better to glue the lip for a VAZ 2114 with fiberglass or carbon fiber. The product is applied with a brush. It is advisable to glue in three layers of fiberglass (for a spoiler - four layers + two windings of tights and mesh). Everything is not done at once, but at intervals to polymerize the resin. It should be remembered that epoxy glue does not dry, but rather polymerizes.

If you plan to install stop bars, side lights or other lights, then the wiring should be done when gluing the spoiler. The glass for the stop bar can be made of epoxy, but the best option is to find a rod of a suitable size made of plexiglass or plexiglass. You need something transparent and fileable.

You should pay attention to the operation of puttying and laying out the plane. At this stage, the spoiler for the VAZ 2114 car takes on its final form. Sometimes this is done with one primer, which is far from the best solution - it takes a long time and the layers are too thick. When sanding is finished you can start painting. This requires approximately 3-4 cans of paint.

Source: https://tuningui.com/spojjler-na-vaz-2114/

VAZ 2114

Good old hatchback. History and tuning of VAZ 2114

Story

2900.00 rub. Your price

Price For registered:

2800.00 rub.

Features of this tuning

The brake light in the spoiler has a number of advantages:

It's stylish, that's why they buy spoilers. Without a spoiler, the VAZ looks like a simple classic car, even a kind of retro, but with a spoiler it looks quite original.
The spoiler best conveys the stop signal, and you can come up with any animation that attracts attention, but you need to be careful with this.
The spoiler has a low price, and almost every driver can install it independently.
The spoiler is installed once for many years, so it is beautiful and profitable.
The brake light on the spoiler is more visible, so even from a road safety standpoint, the spoiler wins.

Although the spoiler is a decoration of the car, it is difficult to say why it is installed on the VAZ. Most likely, this is due to the fact that the car of the classic brand looks modernized and stylish compared to the standard version.

Those drivers who want to figure out how to do all this on their own need to first understand the essence of how microcircuits work, because they are one of the main parts designed to provide information, without which the operation would simply be impossible. It also wouldn’t hurt for the driver to read about the wing in specialized literature.

In order to organize your own installation of a spoiler, you need to purchase a printed circuit board, mounting drills, ferric chloride and the required number of LED lamps (usually no more than 16) from a radio parts store. The printed circuit board is manufactured only according to the diagram.

In conclusion, we can say that the process of installing a brake light on a VAZ-2114 spoiler is simple. The main thing is to get the desired result and be able to use it correctly. Not all drivers use the brake light in their car correctly.

It is important to note that the spoiler requires special attention and the brake light on it is not as easy to operate as it seems. It is necessary to remember the principle of operation of the LEDs on the brake light and control the glow of the bulbs, because the spoiler lights up exactly the way the driver wants. Accordingly, it depends on the driver himself whether there will be a traffic accident or not. Have a good trip!

Where can I buy?

Any spoiler, both in rough and finished form in body color, can be purchased in a specialized online store. This will not only save money, but also familiarize yourself with detailed technical information and view real photos of the car after such external styling.

You can buy spoilers in color only if the car is garaged or has low mileage. Otherwise, the color difference will be very noticeable. In any other situation, you can purchase a spoiler for painting. Such original products have an excellent degree of preparation, so you can even work with aerosol paints in cans.

How to install a spoiler on 2114, following technology

How to Install a Spoiler on a VAZ 2114

We make a spoiler for the VAZ 2114

A device such as a spoiler

on VAZ
2114 , in most cases it is installed by the manufacturer, but it also happens that the car is not equipped with this part. Therefore, when a car enthusiast wants to change the appearance of his car, to give the car a more sporty and brutal look, he installs a spoiler
2114 .

Installing a wing on a VAZ is a rather complicated and energy-consuming process. If you have never done this kind of work before, then installing the part may be an insurmountable task for you. replacing the dashboard bulbs of a VAZ 2114 like the interior lighting of a VAZ 2110. If you are not confident in your abilities, then do not experiment, go to a car repair shop, professionals will do everything quickly and efficiently.

On your own, you risk not only damaging the new VAZ 2114 spoiler , but also the car body. In this case, it is difficult to estimate the cost of repairs. If you are confident in your abilities and have experience working with tools, then you can decorate your car yourself.

The purpose of a spoiler is to improve the aerodynamics of the vehicle

.
The car becomes easier and more pleasant to drive, and operating the car at high speed is safer. If you install
the part incorrectly, then you will not receive any bonuses from the spoiler other than appearance. On the contrary, incorrect installation can reduce the speed of the machine.

Spoiler installation steps

In order for the installation of the part to be successful, it is necessary to act according to a clearly drawn up plan.

If you purchased an unpainted part, it must be painted in the body color before installation. Doing this yourself is very problematic; it is recommended to turn to professionals.
When the spoiler
has acquired the desired color, you can mark the place for its attachment.
Replacing the timing belt on a VAZ 2114 8 valves:. To do this, attach the part to the vehicle
in the place where it will be mounted. The catalyst for the VAZ 2114 is a useful device. Promotes complete combustion of exhaust gases and reduces emissions into the atmosphere. Make sure that all marks are even and parallel. If you are sure of the accuracy, then mark the locations of the mounting holes. The appearance of the entire structure will depend on how accurately you do everything.
If your “fourteenth” does not have holes for the spoiler (this happens in some trim levels), then you will have to make them yourself. To do this, use a small diameter drill. When you are sure that the holes are drilled correctly, you can take a drill of the required size. replacing the rear wheel bearing on VAZ 2110, 2112, Kalina, Granta, Priora, 2109, 2108, 2114 and 2115 — duration: 18:50. At this stage it is very important to act slowly, measuring all sizes. It will be difficult to redo bad work. When drilling holes, make sure that the tool is perpendicular to the trunk. This will allow you to control the size of the holes. Iron shavings are generated during operation. Get rid of it with compressed air or using a vacuum cleaner. The main thing is not to use your hands, as you can not only get hurt, but also damage the paintwork of the car. To prevent the holes from corroding, treat them with a special compound.
Now you can attach the wing to the VAZ. Usually the spoiler comes with all the necessary elements for fixation. Replacing the front pillar on a VAZ 2108, how to replace the front pillar on a VAZ 2108-VAZ 21099?. If you don't have them, then learn that you will need polypropylene washers, bolts and plugs. Replacing support bearings on a VAZ 2114 with your own. The washers are placed under the holes, and only then the spoiler
.
The last stage is the installation of decorative plugs.

Car roof spoiler

Some car owners also install a top spoiler . Some people think that such an addition looks stupid and the car has no use at all, while others, on the contrary, consider it stylish and beautiful.

install either a plastic or iron spoiler on the roof of a VAZ, painting it in the color of the body. Catalyst for VAZ 2114 - luxvaz. On a VAZ 2115, replacing the timing belt is done in the same way as on other front-wheel drive models of this brand.

Although there are car enthusiasts who, in order to stand out, paint the part in a bright color. Each material has its pros and cons.

Thus, iron spoilers can bend at high speeds and are susceptible to corrosion, but they more reliably protect the rear window from dirt. But plastic decorations serve more of a decorative function, but they look more impressive. True, it also happens that when pushing a car out of a snowdrift, you then have to repair the VAZ spoiler, because the part is displaced.

Therefore, before installing such an addition to the roof, think carefully and do not drill holes in the body, as many recommend, but attach the spoiler with double-sided tape or special glue. If this design suits you, then you can secure everything thoroughly, but the tape will hold it quite well.

Now you know how to install a spoiler on the trunk and roof of your car, as well as how to make this part yourself at minimal cost. Whether such decoration is needed for your car is up to you to decide. The main thing is that the vehicle makes you happy and does not break down.

THIS IS INTERESTING: Error codes for Mercedes

Source: https://top-geer.ru/kak-ustanovit-spojler-na-vaz-2114/

Withdrawal procedure

Remove the trunk door trim.
Disconnect the wires of the additional brake light.

It is possible that on cars of early years of production you will have to unscrew the nut securing the ground wire of the additional brake signal from the stud securing the trunk door lock.

3. Using a 10mm socket wrench, tighten the 2 spoiler mounting nuts on the right.

4. We also unscrew the 2 nuts on the left.

5. Remove the spoiler from the car.

On cars of early years of production, the spoiler was attached differently. On them, in the door cavity there were only 2 fastening nuts. From the sides, the spoiler was held on the trunk door using 2 pressure plates. Therefore, to remove the spoiler, you first need to unscrew the plates and then the 2 nuts in the door cavity.

6. Install the spoiler on the car in the reverse order.

What does it look like?

Large spoilers affect the aerodynamic performance of the car. Thanks to these devices, the car is able to reach high speeds while driving and consume fuel more economically. Motorists often use rear and front spoilers.

Tuning VAZ 2114

To properly fix the spoiler, it is recommended to adhere to the following sequence of work:

The length and width of the trunk are measured.
Make marks with a marker in those places where there will be a fastening connection between the device and the car body.
After drilling the holes, remove the chips and paint the edges to avoid rust in the future.
Install the brackets into the hole and secure the fixture using nuts and bolts.
If using a decorative option, it is perfectly acceptable to use an adhesive instead of drilling.

Installing a spoiler on a VAZ 2114

To increase the aerodynamics of their car, drivers install special devices - spoilers. With them, the appearance of transport completely changes. Devices are installed at the rear and front. This makes the design modern and attractive.

How to properly install a spoiler on a VAZ 2114? What secrets will help you do this yourself?

Rear spoiler for VAZ 2114

What does it look like?

Large spoilers affect the aerodynamic performance of the car. Thanks to these devices, the car is able to reach high speeds while driving and consume fuel more economically. Motorists often use rear and front spoilers.

Tuning VAZ 2114

To properly fix the spoiler, it is recommended to adhere to the following sequence of work:

The length and width of the trunk are measured.
Make marks with a marker in those places where there will be a fastening connection between the device and the car body.
After drilling the holes, remove the chips and paint the edges to avoid rust in the future.
Install the brackets into the hole and secure the fixture using nuts and bolts.
If using a decorative option, it is perfectly acceptable to use an adhesive instead of drilling.

Recommendations

Correct installation of a high-quality spoiler on a VAZ 2114 will help reduce vehicle air resistance and fuel consumption. If the fixation of the device is not done correctly, then this will not improve the performance of the car, but, on the contrary, will reduce its aerodynamics.

To prevent this from happening, you should familiarize yourself with the recommendations of experts on how to install a spoiler with your own hands:

If there is no space for installing the device, then there is no need to drill the body. An adhesive sealant is quite suitable. A prerequisite is complete solidification of the substance within 3-4 days;
to prevent rust, it is recommended to lubricate the joints between the device and the body with machine oil or wax;

Installing a spoiler on a VAZ 2114

It is better to paint before installation. It is desirable that the color matches the main color of the car or contrasts;
At the fastening points, if desired, use not a polypropylene seal, but an ordinary piece of vacuum rubber.

Drivers who have doubts about the final result turn to specialized salons, where experienced specialists will do this work quite quickly and efficiently.

Source: https://okuzove.ru/kuzovnoj-tyuning/spojler-na-vaz-2114.html

Chassis

Improving the chassis of a car will not change its appearance in any way, but will significantly improve its dynamic properties and behavior on the road. It is divided into 2 types:

Suspension

Tuning the VAZ 2114 suspension includes both calibration of the entire system, wheel alignment of the car, and modernization of individual parts:

replacing springs;
shock absorber tuning;
installation of anti-roll bar.

These details will increase driving comfort and also improve the car’s behavior on the road: the car will rock less and will not roll during sharp turns.

Engine

Tuning a VAZ 2113, 2114 or 2115 engine is a rather complicated, but feasible undertaking. To slightly increase the power of the machine you need:

reflashing the control unit;
increasing the cylinder diameter by boring.

Among the more effective, but risky methods is installing a turbine and replacing the crankshaft with a new one, with an increased piston stroke. This will reduce the operating time of the car, but can lead to its rapid breakdown.

Visor “Voron Glass” for the rear window of VAZ 2108, 2109, 2114 – 500 rub.
Lip spoiler, unpainted – 590 RUR.
Rear window deflector “M-Version” (2109-2114), tuning – 800 rub.
Trade Auto, 21140-6301116-00 (PVC trunk spoiler without a lamp, for painting) – RUB 1,107.
AvtoVAZ, rear door spoiler in Cosmos 665 color (under the canopy) – RUB 1,900.

Fast and Furious (on metal stands with four mounting points) – 2,200 rubles.
V-Max (fiberglass in transport primer for grinding) – RUB 3,350.
Rs-2 (fiberglass and polyester resin) – RUB 1,500.
Impulse “AVR” (reinforced with mortgages, weight is 3.9 kg) – 2,100 rubles.
Ferrari Ango 2114 (width at the mounting point 125 mm, extending beyond the standard holes) – RUB 2,740.

When installing tuned spoilers on the rear door of a VAZ 2114, a leak may occur in the trunk, which will negatively affect the operation of the rear lighting equipment.

Repair of spoiler VAZ 2114

rust in places where it is attached to the trunk;
an attempt to open the trunk using the spoiler as a lever;
Damage or tearing out of fastenings to the trunk.

Removing rust

The rusted areas are cleaned with sandpaper, treated with a rust converter, washed and painted.

During repairs, special plugs are installed in the technological openings of the trunk. Sometimes these holes are simply temporarily sealed with regular tape.

Repair work

If areas at the fastening points are broken, a suitable piece of plastic is attached to the bolts on the sides to the remaining plastic on the bolts.

Repair stages briefly:

Installation of corrugation.
Film protection.
Foaming (in some cases).
Fixing the bolts with superglue.
Drilling technological holes.
Fixing bolts with plastic (in some cases).
Pouring epoxy.

Installing a Spoiler on Lancer 10

A spoiler is an additional body element designed to configure the aerodynamic features of a car.

Specifically, thanks to the spoiler, you can adjust the downforce of the vehicle, which allows you to customize the car for a specific driving style: for maximum speed or for dynamic acceleration.

Installing a spoiler on a Mitsubishi will allow you to fully reveal the power potential of the car and highlight the advantages of the brand - speed and maneuverability.

Types of spoilers for Lancer 10

When choosing a part for Lancer 10, you should decide in advance on the type of element itself. The following systematizations are distinguished:

Lip - A small lining that is attached directly to the trunk without the use of fastening structures. The lip does not change the aerodynamics, but is a decoration that will complement the visual design and transform the style of the Mitsubishi.
Sportback - This type is designed to distinguish upward oncoming air flows, which increases downforce. Thanks to this, the Lancer Evo becomes more manageable and obedient. A more popular version of the sportback in Rostov-on-Don is the duckbill spoiler, which decorates the appearance of the car, clearly highlighting the rear trunk and gives the car a note of sporty style.
Hatchback - A spoiler for the rear door of a car, the purpose of which is to uniformly distribute air flow. Lancer x with a hatchback body is the least stable in corners and installing a spoiler on the front trunk lid will allow the car to take corners more easily, without fear of skidding or wheels falling off. For the hatchback, the 07 spoiler option with an additional brake light is popular.

When choosing spoilers, you need to take into account the features and type of body, so that the part enhances the properties of the vehicle and does not interfere with the driving process.

How to prepare Lancer x for spoiler installation

The installation of each spoiler is slightly different, but regardless of the type of part, you should correctly prepare the vehicle for tuning. The working surface of the trunk needs to be prepared for installation - identify the geometric center and mark the places for fastening or gluing the part.

Installing a Spoiler on Lancer 10

Then the surface of the vehicle is processed. Before installation, it is recommended to treat the fastening points with a degreaser, and after drilling, treat the holes with an anti-corrosion substance.

Fundamentally! The spoiler must fit tightly to the surface of the car and the formation of gaps or voids between structures is strictly prohibited. Also, when attaching the element, you need to moderately distribute the load - first, attach the center of the spoiler in the geometric middle of the trunk, then tighten all other fasteners with uniform force.

How to install a spoiler correctly: step-by-step instructions

Installing a spoiler is an important part of the repair, because if it is installed incorrectly, the part coming off at high speed can unbalance the Evo car, causing an emergency. So, how are each type of spoiler attached?

Lip. – No drilling work is required to install the lindens – the spoiler can be installed with glue or double-sided tape. There are no problems during installation, but before installation it is recommended to degrease the surface of the trunk and the spoiler itself. This is necessary for a uniform fit of the structure and will prevent the possibility of corrosion.
Sportback. – Because this type directly affects the dynamics of the car, the part must be firmly fixed. Sportback spoilers are installed only with bolts or fasteners with special teeth, so installation requires a drill. It is also recommended to consult with a specialist to install the part in the correct place - otherwise, installing a sportback will cause more inconvenience than benefit.
Hatchback. – When installing a hatchback class, the placement of the spoiler is also important; the structure should be installed exclusively in the final part of the body in order to moderately distribute the dynamic load. However, it is not allowed to install the part on glass or weak plastic.

How much does it cost to install a spoiler: we save on repairs

You can install the spoiler yourself - this part has a simple design, which allows you to save on installation work. But, in order to improve the appearance and properties of the car, it is recommended to consult with specialists or at least study the installation aspects on the Internet.

THIS IS INTERESTING: Renault Megane 1 repair

The cost of a spoiler depends on many reasons: material, structure and design of the spoiler, time of year and demand for sales, etc. Therefore, if the spoiler is needed solely as decoration, you can choose a used option - the main thing is that there are no chips or cracks in the design.

Installing a spoiler will only benefit your car. If you want to modernize your own Lancer 10, improve the style of the car or influence the aerodynamics, then a spoiler is a must!

Source: https://avtotrue.ru/ustanovka-spojlera-na-lanser-10/

VAZ 2114

Good old hatchback. History and tuning of VAZ 2114

Story

2800.00 rub.