How to install the ignition switch on a VAZ 2109

Welcome! The ignition switch breaks quite rarely, but it still happens. After a lock breaks, it of course needs to be replaced with a new one, but how to do this, you ask? Some people still know the answer to this question, but some do not. For those who don’t know, we have prepared this article, which will describe in detail the process of replacing the ignition switch. And at the end of this article you will find a video clip that will describe in detail the process of replacing this lock. Note! To replace the ignition switch, you will need the following tools: First, you will need screwdrivers. When do you need to change the ignition switch and contact group? It must be replaced if it breaks, as well as if the key is lost, and even if the cylinder in the lock stops turning and is stuck in one place. The contact group must be replaced if it is deformed, and even if, after turning the key in the lock, the car’s engine stops starting.

Note! Before you immediately say that the contact group of the lock is to blame for everything, first check the contacts of its wire blocks for functionality. (How to check the contacts of the contact group, see below in the section: “Checking the contacts of the wire block”)

How to replace the ignition switch, check the contact group and replace it on a VAZ 2108-VAZ 21099?

Replacing the ignition switch:

Removal: 1) Starting with “The battery is a rechargeable battery,” unscrew the nut that holds the “-” terminal on the battery and then remove the terminal.

2) Then remove the steering column cover and both steering column switches.

Further, for clarity, the operation will be shown with the steering wheel removed, but you can still remove the ignition switch without removing the steering wheel.

3) Next, insert if the lock allows it, then insert the ignition key into it and put it in position “0”.

Home
Auto garage
How to change the ignition switch on a VAZ 2109

Replacing the ignition switch and contact group on a VAZ 2108, VAZ 2109, VAZ 21099

Welcome! The ignition interlock breaks quite rarely, but it still happens. After breaking the lock, it must be replaced with a new one, but how do you ask? Some people still know the answer to this question, and some don't. For the ignorant people, we have simply prepared this article, which describes in detail the process of replacing the ignition. And at the end of this article you will find a video clip that details the progress of replacing this lock.

Replacing the ignition switch and contact group on a VAZ 2108, VAZ 2109, VAZ 21099

Welcome! The ignition switch breaks quite rarely, but it still happens.
After a lock breaks, it of course needs to be replaced with a new one, but how to do this, you ask? Some people still know the answer to this question, but some do not. For those who don’t know, we have prepared this article, which will describe in detail the process of replacing the ignition switch. And at the end of this article you will find a video clip that will describe in detail the process of replacing this lock. Note! To replace the ignition switch, you will need the following tools: First, you will need screwdrivers, and you will also need a drill, a small hammer, pliers, and you will definitely need to stock up on a chisel!

Summary:

When do you need to change the ignition switch and contact group? It must be replaced if it breaks, as well as if the key is lost, and even if the cylinder in the lock stops turning and is stuck in one place. The contact group must be replaced if it is deformed, and even if, after turning the key in the lock, the car’s engine stops starting.

Note! Before you immediately say that the contact group of the lock is to blame for everything, first check the contacts of its wire blocks for functionality.
(How to check the contacts of the contact group, see below in the section: “Checking the contacts of the wire block”)

Power-up modes used

At each of the turns, the connection of certain devices is provided. There are markings in a circle in front of the socket indicating the position to which a certain mode corresponds.

Null

To activate this mode, just insert the key into the “secret”. In this case, devices that are directly connected to the battery remain active.

Additional consumers will be put into operation after the larva is rotated at a certain angle. Voltage is supplied to pins 30/1 and 30.

The first is “ignition”

In the first position, the driver can turn on the front lighting, such as the low and high headlights. The tidy and interior light up responsively. The connection diagram for the VAZ-2109 ignition switch is activated during this turn, releasing current to the 30–INT pair.

When there is a connection between terminals 30/1 and 15/1, the rear lights, reversing lights, turn signals are operational, and the generator excitation winding is energized. The XX solenoid valve also receives power.

In this position, contacts 30/1 and 15/2 are closed, which ensures the operation of, in addition to the head light optics, the functioning of the fog lights, the rear window wiper and its heating. The headlight cleaners, heater fan and engine cooling system propeller are connected to this contact.

The second is the “starter”

By moving the key to the current position, the driver does not block the connection of electrical consumers that were started in the previous “ignition” position. This fully applies to both the closed contacts of the pair 30/1 - 15/1, and to the pair 30 - INT.

The main change that the VAZ-2109 ignition switch connection diagram provides in such a situation is the activation of a pair of contacts 30–50. This allows the starter to start.

Third – “parking”

At this angle of rotation, consumers started in the “ignition” position and closed contacts 30 – INT remain activated. A closed pair 30/1 - P is also added. It is responsible for the parking lighting.

Typical faults

The lock belongs to the car's ignition system. Let us note right away that if problems are observed, you can fix them yourself, because, as a rule, the “nine” is equipped with an outdated ignition system that does not require diagnostics and repair at a service station.

How to make sure there is a problem

Below is a tip on how to make sure that the ignition switch is really not working:

We insert the ignition key and turn it to a certain position. A short circuit in the circuit must necessarily occur. We look at the diagram: if the key is in position “1”, is the external lighting or control devices working;
It is recommended to check at all positions of the lock. If deviations from the norm are observed, there is a problem with the lock;
You can also check the functionality of the ignition switch in the following way: turn the steering wheel, which should not be blocked. The lock on a working steering wheel should only work when the key is turned a second time from position “1” to position “2”;

You can reliably check whether the lock works like this: take an ordinary portable lamp and connect one end to ground, the other to the lock. We turn on the ignition - if the light is on normally, then the lock is in order. If the light is dim or not at all, the lock is faulty.

Common faults

Among them, the following are in first place:

The lock is jammed. This is even observed in the “nines” when a new lock is installed. The reason is a manufacturing defect or what is listed below.

Note. The lock may also jam due to problems interacting with the starter. In this case, you need to inject a little silicone grease inside the lock and do this every time the lock jams.

The lock may wear out over time and this will cause it to perform poorly;
The ignition switch easily becomes unusable in the event of an unsuccessful attempt to steal a car, as well as any careless handling.

What is

First, let's look at the structure of the castle. Let's find out what it looks like, what it consists of, what its operating principle is, and so on:

As mentioned, the ignition switch is a very important element of the VAZ 2109 car, because almost all available equipment is connected to it.

Note. Although there are components that do not depend on the lock in any way. Here they are: license plate lights, brake lights, parking lights, hazard lights, interior lights and lights on the dashboard.

There are different types of ignition switches: new or old type. The first version without a relay has three positions and a short key, the second with a relay has four positions and a long key.

VAZ 2109 ignition switch malfunction

Scheme

Detailed diagram

Below is a typical diagram of the ignition switch on the “nine”.

In key position “0”	The VAZ 2109 is de-energized, and there is power only in the wires that go directly to the battery
In key position “1”	The following car components are working: external lighting, headlights, instrument lighting, interior light, all control devices, wipers, heated windows, etc.
In position “2”	The starter turns on and all position “1” circuits work
In position “3”	All circuits including brake light

Pinout of lock VAZ-2110, VAZ-2111, VAZ-2112

Pinout of the ignition switch VAZ-2110:

comes +12V for the microphone of the sensor of the inserted key;
the mass comes when the driver's door is open;
+12V goes to the starter (pin 50);
+12V goes out after turning on the ignition (pin 15);
+12V goes out when the key is inserted to pin 5 of the BSK;
comes +12V to illuminate the lock cylinder;
+12V comes from the battery (pin 30);
not used.

Malfunctions

Considering that the ignition switch is designed to perform two functions, all breakdowns are divided into mechanical and electrical. Mechanical malfunctions include jamming of the cylinder in one of the positions when it is impossible to turn the key. Contact group, which is time to change when the car engine does not start when you turn the key or deformation has occurred.

Electrical faults can occur in any position of the key, as they are associated with a violation of the integrity of the electrical network.

In a situation where there is no contact, all components of the system do not function. If there is a contact in the wrong place, a short circuit and overheating will occur, which will lead to the need to install a new lock.

Device

On the VAZ-2109 you can find the ignition of a new, as well as an old model. Older models have 4 positions, a long key and a relay. The new ones have 3 positions and a short key, but there is no relay at all. The ignition switch in the VAZ-2109, as well as in other cars, is designed to perform two functions: to lock the steering column (mechanical) and to close contacts when turning the key (electrical).

The electrical part works depending on the turn of the key:

car de-energized – 0;
voltage supplied to the entire electrical network – 1;
supplying current only to the starter – 2;
turning on emergency lighting.

Read more: Average annual mileage of a truck in Russia

Installing a new device

Now you can finally proceed directly to replacing the broken or worn out ignition switch on your VAZ2114 car.

Removing the ignition switch

To do this, follow the following sequence of actions:

Insert the key into the new lock and turn it to the first position. This will allow the latch, which is responsible for locking the steering shaft, to hide inside the housing structure;
Insert the lock into place following the reverse dismantling sequence;
Install the four retaining bolts and tighten them slightly.

Checking the ignition switch on a VAZ 2108, 2109, 21099

In a working ignition switch of VAZ 2108, 2109, 21099 cars, certain electrical circuits must close when the key is turned.
If this does not happen, then at a minimum some consumers will not work, and at most the car will not start. When searching for faults in the electrical circuits of VAZ 2108, 2109, 21099 cars, do not forget to check the ignition switch.

Required Tools

— Tester (multimeter or similar device in ohmmeter mode). If you don't have a tester, you can use a test lamp (a 12 V light bulb with soldered wires).

Preparatory work

— Remove the lower part of the plastic steering column cover to facilitate access to the ignition switch connecting block.

Checking the ignition switch of VAZ 2108, 2109, 21099 cars

— Find and disconnect the connecting block of the ignition switch under the instrument panel

— On the part of the wiring harness block leading to the ignition switch, check that its contacts are properly closed in a certain sequence

Turn the key in the ignition switch to the available three positions. We use the tester in ohmmeter mode, press its terminals to the closed contacts of the lock, or apply the positive from the battery through a test lamp to one terminal being tested, the negative from the battery to the other. If the contacts close, the tester should show the presence of some resistance, the control lamp will light up. Otherwise, the resistance tends to infinity, the control lamp does not light up.

Sequence of contact closure in the ignition switch of VAZ 2108, 2109, 21099

The key position in the ignition switch is 0 (off).

Live contacts 30 and 30/1

The terminals in the block are brown and pink wires.

The key position in the ignition switch is 1 (ignition).

Live Contacts - 30 and INT (exterior lighting, instrument lighting, high beam alarm), 30/1 and 15/1 (alternator field winding, ignition system, windshield wiper, carburetor solenoid valve control unit, turn signals, reverse light , control devices), 30-15/2 (low and high beam headlights. Fog light, headlight cleaners, rear window cleaner, rear window heating, washer, heater fan, cooling system fan).

The terminals in the block are black and pink, brown and white, brown and blue wires.

The key position in the ignition switch is 2 (starter).

Live contacts – 30 and 50, 30/1 and 15/1, 30 and INT (starter).

Pink and red.

The key position in the ignition switch is 3 (parking).

Live contacts - 30 and INT, 30 and 1-P (all electrical circuits listed in paragraph 2). Contact "P" until 1988 was used to turn on the parking lights.

The terminals in the block are black and pink wires from the ignition switch.

Notes and additions

— To fully check the ignition switch of a VAZ 2108, 2109, 21099 for mechanical damage and melting, remove it from the steering column.

Replacing the lock cylinder itself or the contact group

Replacing the VAZ 2109 lock cylinders requires the following tools:

New cylinder complete with keys
Thin clock screwdriver
Phillips screwdriver
Fine drill
Chisels
Hammer
Pliers

In the event of any breakdown, it is not necessary to replace the entire lock; if the cause of the malfunction lies in replaceable parts, then a partial repair of the lock is performed and replacing the lock cylinders on the VAZ 2109 makes sense when the key stops rotating freely in the keyhole. Another option for partial repair is to replace the contact group; for this, a minimum of tools and a little understanding of the device are enough. Our instructions will help you understand the device:

Nothing and no one forbids you to change the entire lock every time, and even go to a service station if you are satisfied with the price
After removing the casing, access to the switch lock opens
The lock cylinder can, in principle, be removed at this stage
Therefore, we pull out the side pin that holds it in the lock
This can be easily done with a thin screwdriver (clockwise) while tapping it with a small hammer
If the pin cannot be pulled out in this way, then try to drill out the cylinder carefully using a thin drill
If it is more convenient for you to remove it first, remove the ignition switch before proceeding to replace the cylinder, to do this you need to unscrew the bolts securing the ignition switch to the steering column
This must be done using a hammer and chisel, as these bolts have sheared heads.
Use a chisel to loosen them slightly, and then unscrew them with pliers, as in the photo below

Video “Replacing ZZ”

This video demonstrates the repair of the ignition switch of a VAZ 2109 (the author of the video is Vitaly Rau).

Home
Auto garage
How to Replace the Ignition Switch on a VAZ 2109

Ignition switch for vases with cylinder assembly

The ignition switch cylinder of the VAZ 2109, despite its small size and completely inconspicuous placement, plays a major role in the operation of the vehicle systems when assembled with the lock. Therefore, a breakdown of such a small unit can completely immobilize the operation of the entire car. The ignition switch is used to turn on the power for the entire complex of accounting programs for ignition and engine starting, windshield wipers, reversing lights, turn indicators, and in some modifications even a radio and headlights. Additionally, on some cars the ignition switch is additionally equipped with an anti-theft device that blocks the steering wheel from turning. On a VAZ 2109, changing the lock cylinder is painfully simple. The main thing is to study the execution sequence and choose a tool.

Replacing the lock cylinder itself or the contact group

Replacing the VAZ 2109 lock cylinders requires the following tools:

New cylinder complete with keys
Thin clock screwdriver
Phillips screwdriver
Fine drill
Chisels
Hammer
Pliers

Nothing and no one forbids you to change the entire lock every time, and even go to a service station if you are satisfied with the price
After removing the casing, access to the switch lock opens
The lock cylinder can, in principle, be removed at this stage
Therefore, we pull out the side pin that holds it in the lock
This can be easily done with a thin screwdriver (clockwise) while tapping it with a small hammer
If the pin cannot be pulled out in this way, then try to drill out the cylinder carefully using a thin drill
If it is more convenient for you to remove it first, remove the ignition switch before proceeding to replace the cylinder, to do this you need to unscrew the bolts securing the ignition switch to the steering column
This must be done using a hammer and chisel, as these bolts have sheared heads.
Use a chisel to loosen them slightly, and then unscrew them with pliers, as in the photo below

Loosen the bolts securing the lock to the steering column

Now we remove the bracket and the lock itself from the column, be sure to disconnect its electrical connector
We unscrew the screw securing the ignition relay and remove it from under the panel
Disconnect the connector
Disconnect the “mass” wire
Using a Phillips screwdriver, unscrew the screw
Then release the latch and remove the cover, then the contact group
So we pulled the switch
We remove the cylinder with our own hands and the ignition switch, as already described above
We are replacing it
We check the operation of the lock with a new cylinder installed, to do this we turn the ignition key
After installation, do not forget to check the correct operation of the locking mechanism, our steering shaft
When the mechanism does not work when turning the steering wheel fully, you need to adjust the location of the lock on the steering column
Only after completing the adjustment of the location and checking the functionality of our locking mechanism, you can tighten the bolts until the heads come off completely, use a “10” spanner for this purpose

Repair and replacement instructions

Basically, the protection zone can be repaired. Repair usually consists of replacing the core or contact group. If the problem remains after repair, then the ignition switch needs to be replaced.

Core of ZZ VAZ 2109

On a VAZ 2109, replacing the core consists of the following steps:

First, the protective and decorative cover is removed from the steering column, as well as the windshield washer and turn switches.
The lock is secured with screws and a hook latch. There may be problems with unscrewing the screws, since their heads are cut off. To remove them, you first need to loosen them with chisels and then unscrew them with pliers. You can carefully drill out the screws.
Next, we disconnect the clamps, disengaging them.
By pulling out the side pin, you can remove the core. If that doesn’t work, the core can be drilled out using a thin drill. In extreme cases, you will have to dismantle the entire assembly.
The next step is to disconnect the connector, wire plug, and ground wire.
By releasing the latch, you can remove the cover and contact group.
We insert a new core and check the work. When you turn the key, all processes should work.

The steering wheel lock should also be checked. If the steering wheel does not lock when turned fully, you need to adjust the position of the lock on the column.

Replacing the contact group of the VAZ ignition switch comes down to dismantling the ignition switch: the removal diagram is described above.

When performing the procedure, the following recommendations should be followed:

before disconnecting contacts, it is advisable to assign numbers to them, this will help to avoid errors when connecting;
If there is a retaining ring in the design of the contact group, you must first remove it using an awl.

Knowing how the ignition switch on a VAZ 2109 works, and having at least a little experience, you can carry out the repair yourself without resorting to the help of specialists. This way you can save on maintenance costs.

Possible malfunctions and ways to eliminate them

The nature of the lock assembly malfunctions on a VAZ 2109 car can also be electrical or mechanical.

The first group includes violations of the integrity of electrical circuits in the switch at a certain position of the key. If there is no contact, then the connected consumers may not work, or the car will not start at all. If there is contact, but the wrong parts of the circuit are closed, this is fraught with a short circuit and thermal damage to the lock. It will begin to melt and a characteristic smell will appear. Depending on the scale of the disaster, the contact group will most likely need to be replaced.

From a mechanical point of view, the core/larva may become stuck in some position. In this case, it will be physically impossible to turn the key in the lock. The only correct repair option is to replace the entire assembly.

To diagnose faults in electrical circuits, you need to stock up on the following tools.

Multimeter or tester. If it is not available, as an option, you can use a control light operating at 12V voltage.
A set of screwdrivers and keys for dismantling the lock. Since the only option for repairing mechanical faults is to replace parts that have failed, they will come in handy in this case as well.

Before starting diagnostics, you will have to disconnect the terminal block and ring all contacts in the sequence that corresponds to each of the key positions. For clarity, you should have an electrical diagram of the unit at hand. If the circuit is closed, there will be a resistance indication on the device.

Replacing the lock should begin with de-energizing it. To do this, you will have to loosen the fastening nut and remove the negative terminal of the battery. After this, the protective and decorative casing and the turn/window washer switches are removed. The lock is attached to the steering column using four screws or two screws and a hook latch. It may be difficult to remove due to the screws. In this case, they will have to be cut or drilled, doing everything extremely carefully. The terminal block is disconnected, and the dismantling process can be considered complete.

Repair and replacement instructions

Basically, the protection zone can be repaired. Repair usually consists of replacing the core or contact group. If the problem remains after repair, then the ignition switch needs to be replaced.

Core of ZZ VAZ 2109

On a VAZ 2109, replacing the core consists of the following steps:

First, the protective and decorative cover is removed from the steering column, as well as the windshield washer and turn switches.
The lock is secured with screws and a hook latch. There may be problems with unscrewing the screws, since their heads are cut off. To remove them, you first need to loosen them with chisels and then unscrew them with pliers. You can carefully drill out the screws.
Next, we disconnect the clamps, disengaging them.
By pulling out the side pin, you can remove the core. If that doesn’t work, the core can be drilled out using a thin drill. In extreme cases, you will have to dismantle the entire assembly.
The next step is to disconnect the connector, wire plug, and ground wire.
By releasing the latch, you can remove the cover and contact group.
We insert a new core and check the work. When you turn the key, all processes should work.

The steering wheel lock should also be checked. If the steering wheel does not lock when turned fully, you need to adjust the position of the lock on the column.

Replacing the contact group of the VAZ ignition switch comes down to dismantling the ignition switch: the removal diagram is described above.

When performing the procedure, the following recommendations should be followed:

before disconnecting contacts, it is advisable to assign numbers to them, this will help to avoid errors when connecting;
If there is a retaining ring in the design of the contact group, you must first remove it using an awl.

How to replace the ignition switch, check the contact group and replace it on a VAZ 2108-VAZ 21099?

Replacing the ignition switch:

Removal: 1) Starting with “The battery is a rechargeable battery,” unscrew the nut that holds the “-” terminal on the battery and then remove the terminal. (How to remove the negative terminal from the battery, see the article about “Replacing the battery on a VAZ”, in the “first” paragraph)

2) Then remove the steering column cover and both steering column switches. (How to remove the casing and both switches, see the article: “Replacing under-steering switches”)

Further, for clarity, the operation will be shown with the steering wheel removed, but you can still remove the ignition switch without removing the steering wheel.

3) Next, insert if the lock allows it, then insert the ignition key into it and put it in position “0”.

Note! The key must be installed in this position only to disable the anti-theft device!

4) Now remove the four bolts that secure the ignition switch. If you have these bolts with a cut off head, then knock them down with a hammer and chisel. (Be sure to read the “Important!” paragraph)

Note! If that doesn’t work, then try drilling out all four bolts, but just do it carefully without damaging anything!

5) Once the bolts are loosened, use pliers to remove them from the hole.

6) Next, remove the bracket on the left side, and the ignition switch on the right.

7) Now disconnect the wire block from the electrical connector.

And finally, crawl under the dashboard, and there, disconnect the connector going from the ignition switch to the relay.

Installation: Installation of a new lock is carried out in the reverse order of removal.

Checking the contacts of the wire block:

1) First, remove the lock from the car using the text above.

2) Next, using an “Ohmmeter” or a “Multi-meter” with the “Ohmmeter” function enabled on it, connect its leads to the electrical connector and then look at the readings of the device.

Note! The device should clearly display “0”; otherwise, replace the contact group!

Ignition replacement and check

To replace the ignition switch, you need to perform all the steps in a certain sequence:

Before replacing, you must remove the negative terminal from the battery.
Remove the steering column cover and the two switches located under the steering wheel.
After this, you need to insert the key into the ignition switch and set it to the zero position. This is necessary for the anti-theft device to be disabled.
Next, unscrew the 4 bolts that hold the ignition switch. If bolts with sheared heads are installed, knock them down using a hammer and chisel.
After unscrewing (knocking down) the bolts, remove them from the holes using pliers.
On the left side, remove the bracket, and then on the right side, remove the ignition switch.
Then disconnect the wire block from the electrical connector.
Get under the dashboard and disconnect the ignition switch connectors from the relay.

Installing a new lock must be done step by step in reverse order.

To check the contacts on the wire block, use an ohmmeter. The device must display zero. If his readings are different, change the contact group.

To change a contact group, you need to do the following:

Using a screwdriver, unscrew the screw that secures the cover.
Bend back the plastic latches that hold the cover in place, then remove it.
Remove the contact group.

The contact group is also installed in the reverse order.

Not in all cases it will be possible to find four bolts on the steering column on a VAZ-2109. On some models it can be secured with two bolts and a hook.