Replacing the low beam bulb on Lada Largus

What kind of bulbs are in the headlights?

• Low and high beam lamp - H4, power 12V, 60/55W;
• Bulb dimensions - W5W, power 5W;
• Front turn signal lamp - PY21W;
• Fog lamps - H11, power 12V, 55W.

Low and high beam

One lamp is responsible for low and high beam. Its resource is 2000-4000 hours. To gain access to the left headlight unit, you must remove the battery.

1. Turn the lid counterclockwise;
2. Remove the cover by releasing the latch.

1. Remove the block with wires by unclipping the lock;
2. Remove the rubber cover by prying it off by the edge.

1. Unscrew the lamp clamp to the side;
2. Remove the headlight bulb.

Installing a new lamp in the Largus headlight is carried out in the reverse order. You need to hold the lamp by the base; it is not recommended to touch the bulb with your fingers. If necessary, wipe the flask with a microfiber cloth that does not leave lint. The process of replacing the H4 lamp is also shown in the video:

Replacing light bulbs on Lada Largus - photo, video of replacement

Constant use of the car will one day lead to the need to replace light bulbs on the Lada Largus. This is easy to do at a specialized service station, but you can do all the necessary work yourself. To achieve the desired result, you need to carefully study the instructions. This is due to some nuances that should be taken into account when replacing light bulbs on a Lada Largus. Let’s talk about all these subtleties of work in more detail.

What kind of lamps are in the headlights of Lada Largus?

All lamps that are used for outdoor lighting in Lada Largus can be divided into 3 categories:

You also need to understand what kind of light bulbs are needed to replace in a Lada Largus car:

For low beam, use an H-4 bulb with a power of 12V, 60/55W;

For dimensions, you need to take a W5W lamp with a power of 5W;

For the front turn signal, use a PY21W bulb;

The fog lights have H-11 lamps with a power of 12V, 55W.

Replacing low and high beam bulbs on a Lada Largus

Any replacement of light bulbs must begin with turning off the power. These actions are required for working with electrical equipment of a car. The power is disconnected by turning a special lever or removing the terminals from the battery. This way you will completely eliminate short circuits caused by improper connection of wires. You need to understand that one bulb is used for the low beam of Largus, and the second for the high beam. The average lamp operating life ranges from 2-4 thousand hours. You can gain access to the left light by removing the battery.

Turn the lid counterclockwise;

Installing the working light bulb in the Largus lantern is carried out in the reverse order. Remember that you should only hold the lamp by the base, and it is advisable not to touch the bulb. As a last resort, you can wipe the light bulb with a lint-free microfiber cloth. You can watch the correct process of replacing a low beam light bulb in the video:

Replacing side light bulbs on Largus

If it is necessary to replace this lamp, the entire lamp must be removed. This is the only way to ensure access to the side lights of Largus. After dismantling, we disconnect all power wires with extreme care and attention. After disconnecting the power from the battery, you need to remove the front bumper, which serves as additional protection for the dimensions. Ideally, work is carried out with sterile gloves. If the device was accidentally touched, it must be treated with a lint-free microfiber cloth.

• We remove the fender liner by removing the fasteners;
• We remove the socket with the light bulb by turning it in the direction of the clock, and for the right side you need to turn it in the opposite direction;
• Remove the burnt out lamp from the base.

To replace the backlight on Largus, turn the socket counterclockwise. Then carefully connect the 2 wires to the battery. And now all that remains is to install the working lamp and carry out the assembly. Installing all components in place is carried out in the reverse order and does not take much time.

PTF lamp (fog lamp)

There is no access to the lamp from the engine compartment, so replacement is made from below.

1. Remove the fender liner by removing the screws;
2. Disconnect the block from the lamp by pressing the lock;
3. Remove the lamp by turning it a third of a turn counterclockwise.

Install the lamp in the reverse order.

Attention! In practice, replacing lamps in a Largus headlight is much easier. In other words, it is not at all necessary to remove the battery and fender liners (lockers). If you get the hang of it, you can access all the headlight bulbs from the engine compartment.

Let us remind you that other operating and repair instructions for Lada Largus are in this category. It is convenient to find the answer to your question based on the content.

2163-5-13-12-02

...and remove the lamp socket from the headlight housing.
...and remove the lamp socket from the headlight housing.

...and remove the lamp socket from the headlight housing.

We remove the baseless W5W side light lamp from the socket and replace it with a new one.

[How to save on maintenance of Lada Largus] [Maintenance of Lada Largus at 15,000/45,000/75,000/105,000 km] [Maintenance of Lada Largus at 30 thousand km] [Maintenance of Lada Largus at 60 thousand km of run] [Maintenance of Lada Largus for 90 thousand km of run] [Maintenance of Lada Largus for 120 thousand km of run] [Independent maintenance - general recommendations] [Safety rules for self-carrying out maintenance] [Tools required for carrying out maintenance Lada Largus maintenance] [Lamps used in the Lada Largus car]

Changing the lamps in the Lada Largus headlight

How to change the low/high beam lamps on Largus, as well as the dimensions

A note about what kind of lighting lamps are installed in the Largus headlights; which of them are low/high beam, and which are responsible for the side lights. How to change lamps yourself. How much do originals and analogues cost in Yaroslavl?

Good day, future and aspiring gentlemen Largusovod!

On Largus, the low/high beam and headlight lamps often burn out. At least for 70 thousand I have already changed it five times on each side.

The following light bulbs were installed on my car:

1. Low/high beam: halogen, Osram H4 12v 60/55w. (art. 64193). Price from 109 rub.

There are many analogues. Here are some of them:

370 rub. General Electric (34454)

117 rub. Valeo (032007)

2. Front dimensions: halogen baseless 12V Osram (art. 2825). Price from 17 rub.

26 rub. Lynx (L12805)

9 rub. Fortluft (2825)

3. Rear dimensions: two-pin with filament, base BAY15D. Beacon 12V P21/5W.

from 56 rub. Fortluft (7528)

They burn out less often. I changed it only once in the right headlight. This is what she looks like:

How to replace headlight bulbs

1. First, remove the protective cover. It turns a little, then a small latch is released.

2. The block with wires is removed.

3. Remove the rubber protective sleeve.

4. The lamp is pressed U -shaped clamp. It needs to be pulled to the side and back.

5. Take out the lamp. Remember its orientation. Two teeth at the bottom, one at the top. And if you look at it from the side of the headlight, the inscription (marking) will be on top.

6. Install a new lamp. You should not take it with your bare hands, as greasy marks from the pores will remain on the bulb and the lamp will fail faster. This applies to all halogen lamps. It is better to hold it by the plinth or use a microfiber cloth.

7. Assembly is carried out in reverse order. First the clamping clamp, then the rubber bushing and finally the top cover.

How to replace front markers

There isn't much action here. The main thing is to get to the cartridge and turn it 90 degrees. On the left headlight it is clockwise, on the right it is counterclockwise. The most inconvenient thing to change is the battery side. Not enough space. If your hand is large, it is better to remove it.

If you can’t feel the cartridge at all, then the operating instructions advise removing the fender liner.

The procedure is as follows:

• Found a cartridge
• They turned it over and took it out
• Removed the lamp
• When installing a new lamp into the socket, it is better to wear gloves
• Then the cartridge was installed back into the headlight and rotated 90 degrees.

How to replace rear lights

Changing lamps is a pleasure. All you need to do is remove the headlight unit. It is secured with two wings from the interior: one at the top under the plastic upholstery, the other at the bottom. We unscrew them, move the headlight to the side and disconnect the block with the wires.

Next you need to remove the protective cover. It is held on by three latches. There are three lamps underneath it. We find the size lamp and change it. The steps are simple: insert into the cartridge and turn.

Block lights

Structurally, each block headlight of the LADA Largus station wagon consists of two sections. One contains:

• "marker" lamp (W5W).
• double-filament lamp for low and high beam (type H4);

Nearby is the section in which the PY21W turn signal lamp is located.

The headlight unit is dismantled when it is damaged or needs to be modified (tuning).

Replacing the headlight

Before you begin work related to replacing the headlight, you must:

1. Secure the station wagon using the handbrake.
2. Remove the key from the ignition.
3. Remove the negative wire from the battery terminal.

The dismantling of the headlight block of the LADA Largus station wagon begins by first removing the front bumper. This operation is shown in detail on the video page:

Read more: Refinement of the Chevrolet Niva transfer case

After this, access to the fastening elements in the lower part of the case will open. Next, you need to disconnect the electrical wires:

• going to the H4 type lamp. To do this, remove the cover 3 and disconnect the pads;
• remove the sockets for the direction indicator lamps 5 and indicator lamps 7;
• remove the actuator of the headlight hydraulic corrector (if equipped) from the headlight housing, to do this, slide boot 4 along the cable and unclip the fastening latch.

• after this, you need to unscrew the fastening bolts (items 1, 3 and 4) located around the perimeter of the body part (2);

• push the headlight housing forward a little and remove it.

The new headlight unit is installed in the reverse order, maintaining a uniform gap between housing 2 and body parts.

Adjusting the luminous flux

After carrying out any work related to the head optics of the LALA Largus car, it is mandatory to check and adjust (if necessary) the direction of the luminous flux of the switched on lamps. To do this, it is best to contact a specialized service station, equipped with special instruments and staffed by qualified specialists. However, in case of emergency, such an operation can be carried out independently and without the necessary equipment. In practice, there are several ways to check and adjust headlights. You can see one of them by watching the video:

Replacing lamps in a headlight

Among the sudden malfunctions that almost all car owners encounter, one of the first places is the failure of head optics light sources. These include lamps:

• low/high beam;
• direction indicator;
• Dimensions indicator.

All of them are located inside a separate headlight and changing them, if necessary, is not difficult.

Replacing the low/high beam lamp

Change the low/high beam lamp in the LADA Largus headlight in the following order:

• remove the protective cover;

• disconnect the block with wires;

• pull out the rubber seal;
• pressing on the spring holder, remove it from under the latch;

• Carefully releasing the holder, carefully remove the burnt out lamp.

The new lamp is inserted into the reflector hole and secured using standard fasteners. Then all the removed parts are returned to their places.

Attention! Lada Largus uses halogen light sources, the glass surface of which is not recommended to be touched. To avoid darkening of the flask when heated, it is recommended to hold them by the base.

Read more: Does a local police officer have the right to stop a car?

Replacing the turn signal lamp

In order to change a faulty lamp installed in the turn signal compartment, you must:

• gently press out the plastic connector retainer;

• disconnect the connector with the on-board power supply wires;

• remove the lamp socket from the headlight socket by turning it clockwise (left lamp) or counterclockwise (right lamp);

• By pressing and turning the lamp counterclockwise, we take it out.

The new lamp is installed in the reverse order.

Replacing the indicator lamp

A burnt-out baseless bulb installed in the size indicator is changed as follows:

• disconnect the block with electrical wires from the cartridge;
• turn the socket clockwise (left lamp) or counterclockwise (right lamp) and remove it from the headlight housing;

• A new lamp is placed in place of the burnt one.

The cartridge is returned to the standard socket, performing all operations in the reverse order.

Replacing lamps in the headlight (low and high beam lamps, front dimensions, turn indicator)

The procedure for replacing the right and left headlight bulbs is the same.

Location of lamps in the headlight: 1 – turn signal lamp; 2 – headlight adjustment mechanism; 3 – screw for adjusting headlights vertically; 4 – headlight lamp (low, high); 5 – side light lamp; 6 – horizontal headlight adjustment knob

Open the hood and disconnect the negative battery.

Replacing the head lamp (low and high beam)

Headlight bulb H4 - halogen, double-filament.

Turn the plastic cover, press the lock and remove it (in the photo, for clarity, the headlight is pulled out of the cavity in the body)

After releasing the lock, remove the wiring block from the lamp.

Lift the edge of the rubber sealing boot and remove it from the headlight.

By pressing the spring clamp of the lamp, disengage it from the reflector

And remove the headlight bulb (low and high beam) from the headlight housing

Insert the new lamp, secure it with the spring holder, install the rubber seal, attach the wiring block to it and replace the plastic cover.

Replacing the turn signal lamp

Turn signal lamp PY21W (orange).

Replacing the turn signal lamp in the headlight without removing the fender liner or battery can be problematic due to difficult access. Some drivers are able to do this, some are not. If you cannot make a replacement with direct access, proceed as follows:

2163-5-13-12-07

By pressing the lamp, turn it counterclockwise and remove it from the socket.
By pressing the lamp, turn it counterclockwise and remove it from the socket.

By pressing the lamp, turn it counterclockwise and remove it from the socket.

We replace the burnt-out PY21W turn signal lamp with a new one.

Replacing the side light bulb

Before replacing the side light bulb, it is more convenient to first disconnect the wire block from the turn signal lamp socket (see above).

To watch online, click on the video ⤵

Replacing the side light bulb of the front headlight of Lada Largus More details

How to replace side lamps on Lada Largus. Normal people. More details

Replacing a marker lamp in Largus Read more

Replacing headlight bulbs for Renault Logan, Lada Largus More details

Replacing front headlight bulbs on Renault Logan. More details

Installation and replacement of light bulbs in Largus headlights Read more

Replacing the light bulb in the rear light on a Lada Largus. More details

Replacing a light bulb on a Largus. More details

Replacing low and high beam lamps for Renault Logan and Lada Largus More details

Repair of Largus - Replacing the H4 lamp in the headlights on a LADA Largus (practice) More details

Replacing a Lada Largus light bulb Lada Largus More details

Auto electrician Nizhny Tagil. Largus illumination of the stove and buttons. Vingroad pillow. More details

Secret menu of the standard radio for Largus, Logan, Duster, Sandero Read more

DRL on LADA Largus with your own hands for 3 rubles 50 kopecks Read more

Self-diagnosis mode of the instrument panel for Renault Logan and Lada Largus Read more

Free auto electrician. Lada Largus stove blows cold. Replacing the marker lamp and license plate light. More details

Super bright reverse gear PROBRIGHT RL Omega in Lada Largus More details

Replacing fog lamps on Lada Largus Read more

About related faults

A lighting device for any purpose that refuses to perform its function can signal to the owner of the Lada Largus that the fuse is faulty. If it is discovered that the jumper in the fuse link has burned out, then such an element requires unconditional replacement, which also means replacing the marker light bulb. This is quite easy to do. The mounting block is located on the left edge of the interior panel in close proximity to the unit for switching the modes of lighting devices. Here are the inserts numbered F1 - F39. Fuses numbered 9 and 10 are responsible for ensuring the operation of the low and high beam, respectively for the left and right headlights of the Lada Largus car.

Insufficient contact at the terminals in the fuse block can also cause problems with the normal functioning of the head optic components.

Important! When installing the lamp, do not allow your fingers to touch the glass bulb, since marks can significantly reduce the effectiveness of the product and lead to its premature failure.

There may be cases of premature burnout of the contact inside the lamp itself or banal oxidation of contacts with the ground. The last option can be easily eliminated. To do this, it is necessary to thoroughly clean the contacting surfaces of the cable lugs. A wire brush will do.

If these methods do not give the desired result and the functionality of the Lada Largus lighting devices is not restored, then you will need to contact professionals for a more thorough diagnosis of the causes of the malfunctions and their subsequent elimination.

Replacing side light bulbs on Lada Largus

From time to time, replacing a Lada Largus lamp becomes one of the mandatory procedures. The reason for this is that it becomes unusable, which in the dark is not only uncomfortable, but also life-threatening.

Timely replacement of lighting bulbs is the key to comfort and safety on the road

Of course, the service life of this lighting element directly depends on its quality and varieties. Although the terms of use are also important here. Indeed, with constant shaking while driving, it will often be necessary to replace not only the low beam lamp on the Lada Largus, but also the dimensions, brake lights and high beams.

Replacing the tail light bulb

When replacing a lamp at the rear of a car, there are also some features that must be taken into account when carrying out the work.

1. Here, before starting work, you will need to disconnect the negative from the battery.
2. Unfold the trunk lining.

3. Disconnect the wiring harness from the rear markers.

Disconnect the power harness

Two lambs are marked with arrows

Removing the rear parking light unit

This is what the location of the signals on the Logan taillight circuit board looks like.

When carrying out this work, you must be careful, as you will have to come into contact with other elements of the system.

It is not recommended to touch the lamps with your fingers. The work must be done with clean gloves.

Lighting elements of Lada Largus

It is worth noting that all lamps used in headlight lighting of Lada Largus cars are divided into three types:

The most common type of headlights for low or high beam are LED variations, since these are the most powerful and efficient lamps in terms of energy conservation. In addition, they can be used for brake lights, turn signals or markers.

Standard replacement procedure

1. Replacing the low beam lamp, as well as the high beam, begins by disconnecting the on-board power supply. This precedes all electrical repair work. In this case, a special switch is turned or the negative terminal is disconnected from the battery, which avoids accidental short circuits or erroneous connections during installation.
2. The place where the Largus lamp will be replaced is determined. There, the rubber plugs covering the electrical components are removed, and two metal antennae are opened in front of the car owner, fixing them in the reflector. They are separated so that the used parts can come out of their seat without damaging the housing.
3. Next, you need to disconnect the plugs from the wiring that was previously disconnected. Here it is worth paying attention to the order of arrangement, otherwise, during the installation of new parts, everything can be mixed up and they will have to be changed again.
4. After connecting the plug with wiring to the new parts, they are mounted in place and secured with antennae. You should try not to touch the flasks with your hands, as this can lead to their rapid failure.
5. If the light is dim during lighting, and the headlights flash when you turn on the headlights, then it is imperative to restore the contacts of the wires with the vehicle body. This is especially true for a marker lamp, because the fat that gets there begins to evaporate when heated and can cause ignition.
6. At the end of this procedure, you need to put on the rubber plugs and secure all the parts in their places. After this, the car will be ready for use and the driver does not have to worry about malfunctions of the Lada Largus lighting fixtures.

Operations for removing the headlight unit Lada Largus

1. Disconnect the wire from the negative terminal of the battery. 2. Remove the front fender liner - the plastic arch protection.

3. Press out the clamp of the turn signal lamp socket wiring harness block. 4. . and disconnect the block from the cartridge

5. Turn the side light bulb socket clockwise (for the right headlight, counterclockwise). 6. . and remove it from the headlamp.

Read more: Cool congratulations from a motorist

7. Turn the plastic headlight cover 8. . release the cover lock. 9. . and remove the cover..

10. Press the clamp of the harness block 11. . and disconnect the block from the base

12. Remove the protective cover with the headlight corrector 13. Remove the corrector drive cable from the holder. 14. . and disconnect it from the headlight range control unit.

15. Remove the front bumper.

16. Remove the three lamp mounting bolts. block headlights to the radiator frame.

This is how the headlight mounting bolts are located. 17. . and remove the headlight unit.

18. Install the headlight in the reverse order of removal and check that the headlights are adjusted correctly.

Lada Largus is a popular family multi-purpose station wagon, mass production of which was launched by AvtoVAZ PJSC in 2012.

A car of this class is designed to meet the most diverse needs of potential buyers and can be used for both everyday and long-distance trips. At the same time, it feels great in urban conditions and on country roads.

The universal use of this car quite often contributes to damage to the elements of the front optics by stones flying from under the wheels of oncoming or passing vehicles, branches of low-growing bushes, etc.

Replacing damaged head optics and installing new elements is not difficult and can be carried out by almost any car owner, even those without experience in carrying out such work. The only difficulty with this is the need to dismantle the front bumper, where not only fog lights are integrated, but also headlights.

Stop signal

The principle of replacement is similar to the installation of the above-mentioned lamps, but it has its own nuances. Here, first, the trunk lid is opened and its decorative panel is removed. So, in order to replace the brake light, you must first of all clear the approach to the wing nuts.

After removing them, the entire headlight is turned out, which would be very problematic to do on your own. After all, you need to bring out its upper and lower parts at the same time so that they do not become a surprise. After unscrewing the screws, access to the lamp is open. The failed part is replaced, and all the previously listed steps are performed in the reverse order.

Dimensions

A special feature of this procedure is the preliminary dismantling of the headlight unit, under which the side light lamps are located. After this, it is necessary to disconnect the wires from the battery, which is done with extreme care.

Removing the front bumper will allow you to get to the cover that protects the dimensions. Since they come into contact with other light devices, it is advisable to carry out all procedures using sterile gloves. If any device has been touched, it must be wiped with a clean, lint-free cloth.

To replace the side light bulb in Largus, the socket of the old part is turned counterclockwise. The black and yellow wires connect it to the battery, so it turns off from them. A new part is installed in this place, and assembly is carried out in the reverse order.

2163-5-13-12-05

Turn the lamp socket clockwise (for the right headlight - counterclockwise) and remove the socket together with the lamp.
Turn the lamp socket clockwise (for the right headlight - counterclockwise) and remove the socket together with the lamp.

Turn the lamp socket clockwise (for the right headlight - counterclockwise) and remove the socket together with the lamp.

Conclusion

You need to make it a rule to regularly change not only the lamps, but also monitor other lighting elements. After all, the process of reducing their brightness occurs slowly and the driver simply does not notice the deterioration in road lighting.

The side lamps for a Lada Largus car are very dim bulbs, so after they burn out or even without waiting for it, you can replace the side lamps with LED ones! The LED light bulb is very bright and economical! The price is for 1 piece. T-10 lamp socket. Also, this light bulb can be installed in the ceiling lamp, in the glove box, trunk lamp, room lighting, wherever the T10 socket is used.

During operation, observant owners of the universal LADA Largus model noticed frequent failure of low beam lamps in the head optics. This places this unit in the category of short-lived components and therefore requires replacement of the low beam lamp. The manufacturer is aware of the presence of this defect and is making promises to eliminate it as soon as possible. While this is being done, owners need to have knowledge of how to replace the low beam lamp themselves.

How to choose a lighting element?

The standard version of the configuration provides for the use of halogen lamps with an H4 base. This device contains two threads, each of which is responsible for its own light (naturally, near and far). Today's auto accessories market is able to offer its customers several analogue lamp options, structurally based on the following technologies:

Advice! When choosing lamps for your LADA Largus, lean towards the offers of specialized trading entities. The market is full of cheap analogues with Chinese ancestry. They cannot boast of reliability, and the effectiveness of such products is negligible. A useful point here would be to take into account the light characteristics of the lamp.

The most efficient lighting components are diode products. They can be installed not only as low or high beam devices, but also as marker optics or turn signals.

Note that an important advantage of a lamp using diode technology is its high ability to save energy. This factor is directly dependent on the manufacturer and the quality aspects of the product.

Important! During replacement, we remember their location, which will prevent incorrect installation and the need to repeat this manipulation.

Replacing a low beam lamp on a Lada Largus: how much does it cost?

The ability to independently replace light bulbs in your car's lighting fixtures is very useful, as it allows you to save both time and money. Today we will see that replacing a low beam lamp in a Lada Largus is a fairly simple task that anyone can do.

General information about this model

The first LADA Largus car rolled off the AvtoVAZ assembly line and went on sale in 2012. It was a Romanian Dacia Logan MCV, adapted for the Russian market. The car is produced to this day and has four modifications:

• Largus R90 – passenger station wagon for five and seven seats;
• Largus F90 – cargo van;
• Largus Cross is essentially the same five- and seven-seater station wagon, but with increased ground clearance and slightly different exterior and interior trim;
• Largus CNG – production started in 2021. Modification with gas cylinder equipment.

Passenger station wagon (left) and Largus Cross
Note. The first Largus rolled off the assembly line a year earlier - in 2011, but was intended for sea trials.

What lamps are used

Before we figure out how to change a light bulb on Largus, let’s determine what lighting devices are used in the headlights of this car. The Largus headlights have only three lamps:

Low/high beam . Halogen double helix with H4 base. The power of the spirals is 55 and 60 W, respectively.

High and low beam lamp for Largus

Parking lights . Incandescent bulbs with W5W socket. Power 5 W.

Front side light bulb Lada Largus

Turn indicator . Incandescent bulb with an orange cylinder with a PY21W base. Power 21 W.

Front turn signal lamp Lada Largus

Closer to the side there is a turn signal light, in the center there is a device responsible for high and low beam, and underneath it is a side light bulb.

So, we figured out the types of lamps. A bulb with an H4 socket is responsible for the low and high beam. All that remains is to decide which one to choose, because the range of light bulbs with such a base on the modern market is quite wide.

But by what criterion should you choose? Price? Quality of light? Life time? Colorful temperature? All these parameters are important for any light bulb, but, alas, they often exclude each other - cheap cannot be of high quality, and vice versa. This means that we will choose according to the price/quality ratio and our financial capabilities, focusing on the brand.

According to independent experts of the company, the price/quality ratio of the lamps was distributed as follows:

1. Bosch;
2. Osram;
3. Philips;
4. Narva;
5. "Lighthouse".

Of course, the above rating does not mean that you should only take Bosch. The products of this manufacturer are quite expensive, although they have the highest characteristics.

Domestic Mayak lamps, for example, are inferior to Bosch in many respects, but are much cheaper than the latter.

Thus, the choice will depend not only on the desire to get the best, but also on material capabilities.

Important! In order not to buy a Chinese counterfeit instead of Bosch or Narva, we will only buy light bulbs in specialized stores. And the fact that the same lighting device on the nearest market costs half as much should not rejoice, but be alarming.

What do we need for work?

In order to replace the lamps in the headlights of the Lada Largus, we will need:

• Torx key T-20;
• clean cotton gloves;
• replacement H4 bulbs.

Let's start replacing

If everything is ready, then you can start replacing the low beam bulb. In order to gain access to the Lada Largus headlight, you need to remove the plastic fender liners. Take the Torx key and unscrew the screws securing it.

To remove the fender liner, you need to unscrew several screws

There are two headlights in front of us: below is the fog light (PTF), above it is the head light. Naturally, we need the latter. For clarity, in the photos below, all actions will be performed with the headlight removed. We will work from under the wing.

We find the hatch for the high/low beam lamp. It is closed with a protective plastic cover. Press the latch and remove it.

Under it we see a rubber boot, from the center of which protrudes the light bulb power connector. We remove it from the lamp by simply pulling it out.

Now you can remove the boot itself.

In front of us is a light bulb, pressed with a spring clamp. We press our finger on the upper part of the lamp clamp and remove it from under the hook on the reflector.

After this, simply fold the spring down, freeing the lamp.

Now nothing holds the lamp

We take it by the body and remove it from the reflector. It's time to put on gloves, because you can't handle the bulb of a halogen lamp with bare hands: the remaining particles of sweat on it will cause local overheating of the glass, and it will simply melt. If you don’t have gloves, then hold the new light bulb only by the base, without touching the bulb.

If we accidentally touched the flask with our bare hands or simply got it dirty with something, we wipe it with a napkin soaked in alcohol.

We install the device in place of the burnt one, monitoring the position of the keys on the base. One of the keys looks up, two symmetrical to it look down. We fix the lamp with a bracket, put on the boot, power supply, and protective cover. Now you can check if everything works, and if so, then install the fender liner in place, securing it with screws.

On a note. Some craftsmen do without removing the fender liners, performing all manipulations from the engine compartment. But, firstly, for this you need to have the hands of a pianist, and secondly, when working with the left headlight, you will still have to remove the battery.

In order to climb through all these pipes, you need to have the hands of a pianist and remarkable patience

What to do if the light still doesn’t work

If after replacing the lamp the low beam still does not work, you will have to look for the fault. First of all, we check the fuses responsible for the corresponding headlight. They are located in the mounting block, which is located on the left side of the driver and is closed with a decorative cover.

Location of the mounting block in Lada Largus (decorative cover removed)

The low beam is controlled by fuses F9 and F10 for the left and right headlights, respectively. You can find them based on the following photo:

Numbering of fuses in the interior mounting block of Lada Largus Useful! The numbering and location of the fuses are marked on the inner surface of the decorative cover. There are also spare inserts and tweezers for replacing them.

If the fuses are intact, then you will have to look for the problem in the wiring and connecting blocks. The contacts in the pads may oxidize, the wire may fray or, due to poor contact, burn away from the pads. If we have electrical knowledge, we look for it ourselves.

If not, contact a qualified specialist or even a regular electrician.

So we learned how to change low beam bulbs in a Lada Largus ourselves. Now there is no point in wasting time and money on a trip to the service station - after all, you can do everything yourself in a matter of minutes.

How to replace the lamp?

Replacing a low beam lamp in a LADA Largus is not a complex procedure, which is quite feasible for inexperienced owners. Here you will need a simple set of tools. The right headlight will cause some difficulties, since the battery is located nearby. In general, this point can be easily eliminated. We will tell you how to change the lamp.

The lamp responsible for low beam in the Lada Largus has a rubber protective cover. This element can be easily moved to the side using manual force. This is done simultaneously with the removal of the power supply wire block.

The sequence of actions is as follows:

1. We turn off the power to the on-board network by removing the terminals from the battery or turning the switch, which is structurally present in the Lada Largus. This mandatory action implies ensuring electrical safety during the full range of manipulations.
2. We remove the rubber pad that covers the electrical component.
3. Now carefully move aside the pair of metal antennae that hold the lamp in the socket.
4. We disconnect the cable plugs with which the lamp is connected to the on-board network.
5. We mount the new lamp in the designated socket and securely fix it.
6. We connect the cable block to the electrical network.
7. Finally, we return the rubber protective plug to its original place.
8. We install all other previously removed components in their original places. Now you know how to change lamps.

Upon completion of the entire list of manipulations, we are sure to check the correct functioning of the entire set of lighting fixtures, including if the bulb dimensions were replaced.

Important! If suddenly, when checking, the lamps began to emit a dim luminous flux, or the side lights switched to flashing mode, then this indicates insufficient contact with the body. The reasons may include both dirt and ordinary oxidation, and it is not always necessary to replace the size bulb.

Cost of lamps

All of the above lamps can be purchased at almost any auto store. For example, a Philips H4 Premium +30 low beam lamp installed from the factory costs about 120-150 rubles. PTF lamp H11 Philips Eco Vision about 500-600 rubles per joke. All other lamps cost no more than 40-50 rubles.

Low beam bulbs on a Lada Largus car are a short-lived element, so sooner or later car owners will definitely have to deal with replacing them. For beginners, this task usually raises many questions. Therefore, below we will look at how to choose the right one and how to change the low beam bulb on Largus.

Choice

Currently on the market you can find such lamps from a variety of manufacturers, among which are the following:

In addition, domestic Mayak light bulbs have recently proven themselves to be quite good. Their advantages include not only low price, but good quality.

Of course, when choosing lamps you need to pay attention not only to the brand, but also to the following characteristics of the lighting element:

However, it should be noted that such light illuminates the road well only in dry weather. In fog or rain, ordinary lamps are preferable.

Note! To install xenon and halogen lamps, you should contact a service center for help, since this work requires the installation of additional equipment and changes to the software. Accordingly, the installation of such lighting is quite expensive.

Thus, each driver can choose the most suitable light bulb, taking into account his own financial capabilities and the conditions in which the car will be operated.

Replacing the low beam lamp on a Lada Largus is carried out in the following order:

• Next, you need to install a new light bulb in place. It is better to do this work with gloves so as not to touch the glass flask with your own hands. The fact is that traces of fat can lead to rapid burnout of the lamp.
• Then you need to fix the base with a spring clip, put the block on the contacts and then install the plug in place.
• At the end of the work, you should connect the battery and check the operation of the headlights.

This completes the replacement of the low beam lamp in Largus. As we can see, this operation is carried out extremely simply.

If, after replacing the lamp, the low beam on the Lada Largus still does not light up, the cause of the malfunction may be a blown fuse. Replacing them is even easier than the paws, since they are located in the cabin, on the left side of the steering column.

• F9 - left headlight.
• F10 - right headlight.

Often the cause of the malfunction is poor contacts of the fuse terminals. In this case, you just need to clean them.