While using a car, drivers often encounter burnt-out lamps in the PTF. Replacing a fog light bulb does not take much time and does not require special tools.
- halogen,
- LED,
- gas-discharge.
The design of the fog lamp reflector differs from the type of light source. Changes concern the shape, wiring system, and cooling.
Car enthusiasts often install LED lamps or xenon in headlights that were designed for halogen. In this case, the formation of the correct light beam is impossible, as is the provision of proper lighting. Independent intervention in the structure causes unwanted light to appear, which blinds oncoming drivers.
To select the appropriate base and type of light element, you should use electronic catalogs that require a VIN number. A proven option, so as not to make a mistake, is to dismantle the part from the fog lamp and go to the store with a sample in hand.
Classic halogen
Fog lights use a regular halogen lamp. The type of base depends on the make of the car, most often it is H7 or H1.
When choosing a new part, preference should be given only to well-known companies that have proven themselves well in the market. These include:
- Koito,
- Philips,
- Osram,
- MTF
- Narva.
Products from dubious manufacturers can not only damage the glass of the headlight, but also melt the plastic housing. It is also necessary to observe the voltage and power of the part. The parameters are indicated on the flask or body of the original consumable.
Halogen-type lamps have a yellowish glow, consume from 35 to 75 watts and last about 2-4 years.
LED lamps
LEDs are characterized by reduced energy consumption and a bright glow with a white tint. Durability can exceed 10,000 hours, which equates to 5-8 years of use.
Types of lamps for PTF
Fog lights not only perform their direct functions, but also help correct deficiencies in the headlights, and also illuminate the side of the road at night. Thanks to the low location of the PTFs, they illuminate the road efficiently without scattering the light.
Halogen lights are usually installed in standard optics. There are drivers who are not satisfied with them, in which case it is necessary to replace the fog lamp with an alternative option. It is important to know which light bulb is better.
There are three types of lamps:
Before replacing PTFs, you should decide on their type. When choosing which lamps are best to install in fog lights, you need to find out the pros and cons of each type.
Halogen
Fog lights typically use halogen products. They are more affordable, shine quite effectively in foggy conditions, and do not blind oncoming drivers.
The disadvantages include:
- short service life;
- difficulty of replacement;
- the headlight gets very hot.
When replacing standard light bulbs with more powerful ones, the power supply may burn out and the headlights will automatically turn off.
Philips halogen lamps
LED
The LED version is very popular for fog lights. In this case, it is possible to choose color and brightness. In addition, diodes consume significantly less energy.
The disadvantage is the high cost. High-power LEDs require additional cooling.
LEDs for PTF
Gas discharge
Xenon used in PTFs makes them bright and efficient. Service life is three years. But the use of gas-discharge elements has limitations. Xenon can only be installed on optics marked with the letter “D”, and an automatic corrector must be installed. The disadvantage is the high cost and the need to replace both bulbs if only one burns out.
Fog lights with xenon for cars
Location of PTF
In accordance with regulatory documents, fog lights must be installed on vehicles exclusively in pairs at a distance of no more than 250 mm from the lower edge of the lens to the road surface. In this case, the distance from the edge of the car’s side dimensions to the center of the PTF should be less than 400 mm. In addition, when installing fog lights, the condition of their location must be observed no higher than the level of the low-beam headlights or head optics, if it is made on the principle of combining low and high beams. The exception is off-road vehicles, on which the main headlights can be mounted higher.
The maximum sector of PTF illumination in the vertical plane should be within -10°—+15°. In the horizontal plane, respectively: -10о—+45о. It is allowed to turn on the fog lights only when the side lights are on.
Depending on the specific vehicle model, fog lights can be included in the basic package or integrated into the headlight units, provided that the fog light bulbs are installed below the main optics bulbs. In some modifications of cars, PTFs are installed separately. In this case, they are usually mounted on the front bumper.
Which ones are better?
Typically, standard optics have halogen elements; replacing them with the same ones, but more powerful, makes no sense. It is better to install LED lamps in fog lights; a good option is to replace the fog lamp with xenon (author of the video - Learning to drive a car. All the secrets for beginners.).
LEDs can be installed in PTF without restrictions, unlike xenon. Replacing a light bulb in a fog lamp does not require special equipment or specific knowledge, so you can replace it yourself. It is better to buy products from trusted brands, since cheap Chinese samples are often of poor quality and quickly fail.
When purchasing LEDs, you need to select a lamp with a base similar to the halogen counterpart. An important parameter for fog lights is brightness, measured in Lumens (Lm). Fog lights with xenon must have a brightness of at least 1000 lm.
How to choose a high-quality lamp for fog optics?
When choosing a light bulb, you need to consider the design of the headlight. The dimensions of some PTFs do not allow the use of powerful lamps that are large in size. When choosing elements, take into account the following nuances:
- when replacing only one light bulb, take into account the brightness and type of element in the other headlight;
- take into account the dimensions of the old lamp;
- the manufacturer may indicate the maximum permissible power of lamps for PTF;
- when buying a light bulb for standard fog optics, it is recommended to choose original products;
- Cheap lamps usually fail quickly, so don't skimp.
Advice! If you notice that the light bulbs have to be changed quite often, look for the cause in poor contacts or faulty wiring.
Lamp replacement guide
It is more convenient to change light bulbs in PTF on a lift or inspection pit. To do this, you need to purchase either the same light bulb as the one you had, or one that matches the parameters. Changing a light bulb is easy.
To do this, follow the following sequence of actions:
- To remove the optics, you need to unscrew the mounting bolts.
- First you need to move the rubber protection to get to the PTF power supply block.
- Then you should disconnect the block from the optics.
- To remove the light bulb, you need to gently press one end of the latch and slide it down.
- The light bulb is removed along with the base. The halogen lamp has several contacts that should be remembered in order to correctly install the new one.
- Next, you need to install the new product so that all contacts match. If you make a mistake, the fog lamp will not light.
- Assembly is carried out in reverse order.
- After assembly, you need to check the operation of the optics.
Replacing fog lights on other car brands depends on their design features. There are cars on which the fog lights are located together with the head light, in which case a slight disassembly of the optics will be required. An example would be the Lada Kalina.
REPLACING A BULB IN THE FOG FLIGHT OF A PRIOR 1 — search by DRIVE2
Replacing fog lamp glass. - Lada Priora .
Review from the owner of Lada Priora
station wagon - do it yourself.
The glass in
the foglight
sits on sealant.
the light bulb
during the
replacement
so as not to touch it with your fingers.
Priora
As I understand it, the last of the Ladas
has foglights
not as a set, but one at a time.
LED lamps in PTF — Lada Priora Universal.
I decided to install high-quality LEDs in the fog lights. I don’t accept xenon on principle)… there are a lot of problems… reworking the wiring, ignition units, etc.
Replacement of light bulbs in PTF and a gift from a loved one - Lada Priora.
Old light bulbs
melted!
and swollen, so they could not be pulled out of the PTF
and they had to be split right in the fog and the bumper removed to get the fragments out.
I installed these new light bulbs
: They seem to shine well and are inexpensive, I hope they don’t melt.
How to change PTF light bulbs without registration and SMS - Lada.
Review from the owner of Lada Priora
hatchback - electronics.
It was during the day, I came to the garage to change PTF
light bulbs .
I took the boards, first carefully drove onto the first
a couple, then added a second one and thus
you can almost walk single file Priora
installation of LED bulbs in foglights in a restyled one.
Lada Priora
Sedan › Logbook › installing LED
bulbs in foglights
in a restyled bumper.
Lada Priora
Sedan 2012, petrol engine
1.6
l., 106 l. p., front drive, manual transmission — accessories.
replacing light bulbs in the PTF without removing the bumper - Lada Priora.
Full size. By unscrewing the plastic flaps along the edges of the bumper, you can access the light bulbs
It’s not free, but it’s there; by twisting your hand, you can find the position to get to
the light bulb
.
Full size. White light. Full size. light bulbs
. Full size.
Replacing the bulb in the fog lamp. - Lada Kalina.
Hi all! So the hour came when the first
light bulb
on my girl burned out) By the will of fate, it became
the light bulb in
the left
fog light
.
To replace it
lamp
(12V 55W PGJ19-2) from Osram was purchased
I swap the fog light bulbs with the dimensions - Lada.
Lada Priora
Station wagon › Logbook › I swap
the fog light
bulbs with the dimensions. niocrv last online 6 hours ago.
It is necessary to trim a couple of antennae on the cartridges so that they can be easily inserted into the headlight
. It turned out not bad, but I dropped one of the clamping screws somewhere.
Replacement of fog lights - Lada Priora Sedan, 1.6 l., 2010.
Hello everyone reading. Today we will talk about replacing
light bulbs in fog lights
.
There’s not much interesting here, so I’ll make up for it by throwing in some useful information. The bulbs in the foglights of the Priors
have the index H11 Now the background: From the very moment of purchase.
THAT. Oil change, filters, fog light bulbs - Lada.
Changed
filters (which lasted 10,000 km)
changed the lamps in the foglights
I also went to the mechanic to inspect the chassis.
Lada Priora
Station wagon › Logbook › TO.
change
, filters,
fog
lights .
I changed the light bulbs on the fog lights - Lada Priora.
Changed
for diode
bulbs
on
the foglight 1
photo after 2 photos before.
Which bulbs are better for the PTF on the Priora? — Lada Priora Sedan.
Review from the owner of Lada Priora
sedan - electronics.
Hi all. In general, one light bulb in the PTF
.
What kind of light bulbs
would you recommend buying with an H11 socket and preferably a photo of the box. For price and quality. They were standard.
Replacing lamps in PTF - Lada Priora Sedan, 1 .6 l., 2010.
Review from the owner of Lada Priora
sedan - consumables.
I bought
Koito H11 WhiteBeam III
lamps The reason one
Osram Night lamp
I heard about them, they seemed to be praised, so I bought them and put them in one PTF
Koito left Osram in another, well, about the color, but really a little.
Priora se fog lights and replacement of lamps with 100W 4200K - Lada 2110.
They also came from Ali lamps
100W, at first I bought all sorts of OSRAM, RHILIPS, but even they were barely, and when I put the film on
the headlights
, they stopped shining altogether, I bought MAYAK, also 100 watts, but they
Well, I drove the 100 for a year, yesterday I installed new light bulbs
, they write to me that everything will burn.
[034] Replacing PTF lamps of H11 socket. — Lada Priora Sedan.
At the end of January there was heavy rain in Makhachkala and in my area there was an unreal flood and the water rose to a decent level. Since I needed to get home, I drove straight ahead, forgetting to turn off the PTF
.
The result was that the lamps
burst and stopped working.
Replacement of low beam and PTF lamps and an epic task of selecting dimensions.
Review from the owner of Lada Priora
sedan - electronics.
Summer is over and I decided to remove the diodes from the PTF
, which don’t shine at all, besides, it will soon get colder and
replacing the PTF
in the cold on a new bumper is of course very problematic. Yes, and I decided that daylight hours are decreasing.
Replacement of fog lights and installation of xenon.
lamps has been lying in storage for a long time
5000k for
fog lights
, but everyone couldn’t get around to removing the bumper and installing it correctly. As it turned out, removing the bumper is not difficult.
I changed the light bulbs in the low beam and fog lamps - Lada.
Lada Priora
Sedan › Logbook ›
Changed the light bulbs in
the low beam and
fog lights
. Piznes last online 2 days ago.
Lada Priora
Sedan 2007, petrol engine
1.6
l., 98 l. p., front drive, manual transmission — electronics.
New light bulbs for foglights - Lada Priora Sedan.
Recently my light bulb
MTF (Argentum) +50% in the right
fog lamp
.
The trouble is that light bulbs
are not sold individually, and I didn’t want to buy 2
light bulbs
that cost more than 900 rubles, which I also don’t think will last more than a year.
PTF bulbs — Lada Priora Hatchback, 1 .6 l., 2009
Oh, to be honest, they got me, initially I didn’t have PTF
, after the accident, I
changed
the bumper and decided to install them, well, I installed everything and they started to mess with my brains, then the Earth was poorly screwed on, then
the light
out in a hole.
Our step-by-step instructions will help you replace a burnt-out fog light bulb on your Lada Priora yourself.
Comments and reviews
Ivan Ivanovich Baranov
Experience working at a service station:
View all answers
Avtozam.com - your assistant in car repair and maintenance
Your use of this website constitutes your agreement that your use is at your own risk.
Not all maintenance processes require contacting specialists. If you don't want to pay extra money for simple procedures, you should learn how to perform them yourself. But in the design of modern cars there are not many tasks that can be done with your own hands. Previously, with a little preparation and good instructions, it was possible to perform virtually any process of car repair and maintenance with your own hands. Today, manufacturers have done everything to protect drivers from performing their own repairs. Therefore, you have to turn to professionals and pay money even for trivial work.
However, there are a number of options for servicing the machine yourself. For example, everything related to replacing lighting elements can be done with your own hands without difficulty and without extra costs. To change the light bulb in the fog light, all you need to do is acquire a high-quality lighting element, look at the replacement instructions and follow this procedure. The main features of this simple procedure are the careful execution of all tasks. Let's look at several important aspects of doing this job.
Replacing a light bulb
Choice
First of all, it should be said that the low beam lamp for the Lada Largus uses a halogen H4 standard, i.e. contains two threads and is responsible not only for near, but also for distant lighting.
Currently on the market you can find such lamps from a variety of manufacturers, among which are the following:
- Bosh;
- Osram;
- Philips;
- Narva, etc.
In addition, domestic Mayak light bulbs have recently proven themselves to be quite good. Their advantages include not only low price, but good quality.
H4 standard lamp
Advice! It is advisable to purchase light bulbs in specialized stores, since recently a lot of counterfeit products from China have appeared that quickly fail or produce poor-quality light.
Of course, when choosing lamps you need to pay attention not only to the brand, but also to the following characteristics of the lighting element:
| Characteristics | Optimal parameters |
| Brightness (light beam power) | Up to 1550 lm |
| Lifetime | Up to 1500 hours |
| Power | 45-60 W |
Standard halogens provide an unnatural yellowish glow. However, recently light bulbs have appeared with a bluish glow. People call them pseudo-xenon.
In the photo - a pseudo-xenon bulb
However, it should be noted that such light illuminates the road well only in dry weather. In fog or rain, ordinary lamps are preferable.
Moreover, in bad weather, even the expensive “xenon” and “LEDs” are inferior to the latter, the power of the light beam is one and a half to two times more powerful than that of halogen bulbs. This is due to the fact that the light of these elements has insufficient penetrating power.
Note! To install xenon and halogen lamps, you should contact a service center for help, since this work requires the installation of additional equipment and changes to the software. Accordingly, the installation of such lighting is quite expensive.
Thus, each driver can choose the most suitable light bulb, taking into account his own financial capabilities and the conditions in which the car will be operated.
Headlight plug
Replacement procedure
Replacing the low beam lamp on a Lada Largus is carried out in the following order:
- Work should begin by disconnecting the terminal from the battery.
- Then you need to remove the plug from the back of the headlight. To do this you need to turn it slightly.
- After this, you should disconnect the block from the contacts by pulling it by the body.
- Next, you need to remove the spring retainer from the grooves with your finger. After this, the bulb is easy to remove from the headlight, since nothing else holds it.
Spring retainer
- Next, you need to install a new light bulb in place. It is better to do this work with gloves so as not to touch the glass flask with your own hands. The fact is that traces of fat can lead to rapid burnout of the lamp.
- Then you need to fix the base with a spring clip, put the block on the contacts and then install the plug in place.
- At the end of the work, you should connect the battery and check the operation of the headlights.
Advice! It is advisable to change the bulbs in two headlights at once to ensure that they glow equally, and also to avoid the second bulb burning out, which can happen at the most inopportune moment.
This completes the replacement of the low beam lamp in Largus. As we can see, this operation is carried out extremely simply.
Types of lamps for PTF
If PTFs are installed by the automaker, then they use standard halogen lamps. Many motorists are not satisfied with them, which forces them to look for replacement options. There are currently three types of lamps on the market that can be used for fog lights:
- halogen;
- LED;
- gas-discharge, or xenon.
Before choosing the final replacement option, you should determine which bulbs are in the foglights. The main difficulty for most drivers is to correctly decide which lamps are best to install in fog lights - each of them has certain advantages and disadvantages.
Halogen
The most common type for fog lights, which has an affordable cost as its main advantage. Such elements ensure acceptable PTF efficiency in foggy conditions, and when properly configured, do not cause blinding oncoming drivers. Among the disadvantages of halogen lighting is a short working life, and replacing a bulb in a fog lamp is not always an easy task. In addition, the headlight becomes very hot, which, if it cools suddenly, can cause the glass to crack. If the power of the standard lamps for the driver is insufficient, when replacing the lamps in the fog lights with more powerful ones, there is a high risk of the control unit overheating and the headlights automatically turning off.
LED
A more acceptable option for most. They feature a wide range of colors, brightness and low power consumption. The LED fog lamp heats up very little due to its unique operating principle. This allows you to avoid melting of the internal parts of the headlight during prolonged operation of the PTF. They almost never cause blindness to oncoming drivers. The disadvantages include higher cost, as well as the need to carefully select the lamp itself - they are not suitable for every headlight.
Gas discharge
Xenon allows you to make fog lights as bright and effective as possible. The service life of high-quality xenon is about three years, but xenon can be used for foglights only in accordance with strict rules, violation of which will not result in a fine, but in deprivation of rights for up to one year. So, for xenon, you can only use special headlights marked “D”, and an automatic corrector is required. Self-installation of xenon in fog lights is more complex than other types of lamps, but if installed correctly, the result will please you for several years in a row. The disadvantages of gas-discharge lamps, in addition to their high cost, include the need to replace both lamps if only one burns out.
Which lamp is better to choose?
Before purchasing, you need to determine the characteristics of a standard headlight. To do this, you need to consult an electronic directory on the Internet or read the markings on the glass or fog lamp housing.
The code is most often applied to the back of the headlight or to the bottom of the glass. An important parameter is power and base. If the requirements are not met, the following problems arise:
- cracking of the case or glass;
- reflector melting;
- strong illumination and blinding of drivers;
- overheating and melting of the wiring.
How to replace a lamp yourself
Replacing a fog lamp lamp itself is not a complicated operation, and if the lamp is replaced with one similar to the burnt one, practically no problems arise. Before starting work, for example, on a VAZ family car, it is advisable to drive the car into a pit, use a lift or raise the front part with a jack. This way it will be much more convenient to work, and less time will be spent.
Before changing the light bulb in the fog light, you should buy a similar one - in this case, it is better to give preference to well-known brands with a good reputation. For VAZs, the process of replacing a light bulb is as follows:
- the fog lamp power supply is found, the rubber protection moves away from the headlight;
- after this the block is carefully disconnected;
- the spring clips on the headlight reflector are unlocked;
- the light bulb is removed along with the wire;
- a new lamp is installed;
- The headlight is reassembled and checked.
It is enough to perform this manipulation once, so that the next time it takes only a few minutes to replace the light bulb in the fog light. The replacement process on other models depends on the design features of the foglights. On some cars, the PTFs are located in a block with the headlights - here you will have to disassemble the optics a little. An example of a replacement on a domestic Kalina in the video:
How to replace a rear fog light bulb
REPLACING FOG LAMPS, REMOVAL OF FOG LAMPS
Fog lights are installed in the niches of the lower part of the front bumper. Replacing lamps in the left and right fog lights, as well as removing them, are performed in the same way. These operations are performed the same on cars with all types of bodies. It is more convenient to work on an inspection ditch, overpass or lift, but it is also possible on a flat, dry area. To replace the lamp, open the hood. We unscrew the self-tapping screw securing the headlight (see “10.7. Ford Focus II. Removing the headlight, replacing headlight bulbs and direction indicators”)
If the standard fog lights are not satisfactory
You can often meet motorists who are categorically dissatisfied with the light of their standard fog lights. This is especially true for those who often travel long distances. Indeed, often in conditions of heavy fog, installed PTFs do not cope with their main task. As a rule, such headlights have conventional lamps. It is not advisable to replace them with similar ones, but with higher power; it is much more reasonable to replace them with LEDs or xenon.
It is worth noting that LED lamps in fog lights can be installed without any restrictions and conditions, as is required for xenon. To independently replace a halogen lamp with an LED one, you do not need special knowledge or equipment. But there is one rule that should not be neglected: you can purchase diode dumps for fog lights only if they belong to a trusted brand. Inexpensive Chinese samples do not meet quality requirements and do not last long.
Before purchasing LED lamps, you should remove the halogen lamps and look at the base to find a similar one - this will allow you to minimize the work of fitting the lamps into a standard fog lamp. An important parameter of a fog lamp is its brightness value. This parameter is measured in Lumens (Lm), and for fog lights the brightness must be at least 1000 Lm, otherwise the effect, compared to halogen lamps, will become invisible.
Diode bulbs in fog lights almost never cause any complaints when passing a technical inspection; they do not require the purchase of expensive lensed headlights. As with xenon, they have a wide range of possible colors, which will allow you to do without installing additional light filters.
To change the light bulb in the fog light on a Nissan Note yourself , you need to arm yourself with a screwdriver (Phillips + flat head), the light bulb itself and a pair of free hands.
Those who love the non-standard, or who want to decorate their car a little, can find taillight covers at https://www.russ-artel.ru/, they are also called cilia. And they are available for both rear and front headlights. This is a fairly inexpensive way to slightly tune your car, thereby making it stand out from the crowd of production cars.
LEDs in foglights are now very popular, there are even yellow LEDs. In my opinion they look very good and shine brightly with a white glow. So which diodes to choose in PTF?
LEDs for front fog lights
H8 35W lamps
. All the light bulbs are in Raccoon.
In the photo on the left you see the best-selling LEDs in PTF. The diodes are very successful: they shine very brightly, with pure white light.
They have their own cooling and have been working for many car enthusiasts for a long time.
When ordering, specify the base correctly - H8 and be sure to read the reviews to decide for yourself whether to buy or not!
Replacing lamps
A photo report will be made on the left fog lamp. The right PTF changes in exactly the same way as the left one, nothing interferes with it, such as the windshield washer reservoir. Everything changes the same way!
To replace the bulb in the fog lamp, the first step is to turn the wheel as far as possible to free access to the fender liner. Wipe the fender liner with a damp cloth to avoid getting dirty during further work.
Next, unscrew the self-tapping screw (bottom) and take out the two clips securing the fender liner:
To remove the clips
fastening the fender liner, you need to pry the core of the clip with a flat screwdriver and pull it out about 5 mm, then pry up the wide part and pull out the clip.
After you have released the fastenings of the fender liner, bend it by hand, thereby providing direct access to the fog lamp.
To replace the lamp in the laptop's foglight, turn the lamp socket in the PTF itself counterclockwise, pull it out as close as possible and replace the burnt-out lamp with a new one. The light bulb is simply inserted into the plug. Try not to touch the glass part of the light bulb and not get it dirty. The service life of the light bulb depends on this. The cleaner it is, the longer it will last!
Article rating:
About the types of additional light lamps
In automobile lighting devices intended for foggy weather, rain or snow, 3 types of light bulbs are used:
- halogen;
- xenon (bi-xenon, gas discharge);
- LED
Before replacing a faulty lamp, you should find out what type is on your car. This information is indicated in the operating instructions.
As a rule, manufacturers equip budget and middle-class cars with halogen bulbs, while business and premium cars use xenon bulbs.
Devices equipped with halogen elements emit a yellowish light that practically does not blind oncoming drivers. Therefore, there are no restrictions on the use of such light bulbs, and they are the most affordable. There is only one drawback - the strong heating of the headlight unit and glass, which can crack if water gets in.
LED elements are more expensive than halogen ones, but they do not heat up as much and consume much less current. This property is relevant for forgetful motorists who do not turn off their headlights when parked. Diode lamps emit white light, slightly inferior in brightness to halogen lamps. There are no restrictions on their installation by law.
You cannot replace a regular fog lamp bulb with an expensive xenon one. The exception is cars where such elements are installed by the manufacturer. According to the law, the optical unit with a xenon lamp must have an automatic luminous flux corrector. Its task is to maintain the beam of light at the same level at different vehicle loads, so as not to blind oncoming drivers with bright lighting. If you want to switch to xenon, you will have to install a new headlight equipped with such a corrector.
When buying new lamps for fog lights, choose them according to the power specified in the car’s owner’s manual. You should not install more powerful elements in pursuit of good lighting, as they will overheat the glass and quickly fail.
We recommend: The stove on the VAZ 2109 does not heat well - causes and repairs
Don't like standard PTF? It's time to act!
Standard fog lights really often do not suit car owners. This question is relevant, first of all, for those who are forced to travel long distances at different times of the day and in any weather. As a rule, standard fog lights are equipped with halogen lamps. What should I do to solve the problem? Replacing them with the same ones, but a little more power, simply does not make sense. We recommend choosing xenon optics or LEDs.
As mentioned above, xenon has certain limitations that must be taken into account. But LED elements are more convenient in this regard. We recommend buying just such light bulbs, but not sparing money on products from trusted manufacturers. Installing cheap Chinese lamps will not lead to anything good; it is better to drive with standard halogen lamps. When purchasing LED lamps, consider what base the standard element has.
To consolidate the knowledge gained, we recommend watching a video about replacing a fog light bulb on a Kia Cee'd:
Content
