Replacing windshield wipers on a Priora with your own hands: choosing suitable models, how often you need to change them, replacement instructions for different options

Good day everyone. If you are tired of the dull work of janitors when the cold weather arrives, then this is the place for you. I have a Priora with air conditioning, and I worked alone, so everything unreal is real. But I’ll say right away, a couple of points, namely the removal and installation of the trapezoid made me a little angry, and I remembered the designer with all the “good” words. and now in detail. -Priora with air conditioning - I took pictures without disconnecting the engine; I didn’t take my own photos, so I’ll take them from the Internet.

1. Stop the wipers in the upper position (vertical) by turning off the ignition. We remove the wipers. We remove Part of the Jabot, it is not necessary to remove all of it. (if the Jabot is swollen, it is advisable to replace it with a new Jabot, which was initially glued with double-sided tape). We take out the coolant reservoir and put it aside (I did not remove it completely as others did) and bend the fixing platform of the reservoir. The yellow arrows indicate the nuts and bolt that need to be unscrewed to remove the trapezoid, plus do not forget to disconnect the power harness.

The removal process itself was quick, on the spot we snap off the upper link on the left side with a screwdriver and bending the body with the handle of a hammer (so as not to damage it with a screwdriver), we gradually remove the trapezoid, using the handle of the hammer and you can use a screwdriver to displace the trapezoid... I took 3 photos of the assembled trapezoid from all sides with a motor, they were very useful to me because after completely disassembling the trapezoid I forgot what came from where, but from the photo it was not difficult to assemble everything in 2 minutes. If you are not going to remove the motor, then remember, mark the pulley in what position, this is the main thing.

2 I bought a repair kit on the market, as it seemed to me that on the Priora and on the Kalnu and on the 2110 they are the same. The Kalinovsky differs in one thing, it is a different size. (If you have a small town and there is no opportunity to buy a Priorovsky, but there are a couple of Kalinovskys then why not? but I bought PRIOROVSKY =) 130 rubles.

The front windshield wiper on the Lada Priora has a design similar to the tenth family, so this repair will be similar. But still, some points will be different. So, repair or replacement of some parts usually occurs for the following reasons:

1. Windshield wiper motor failure
2. Trapezoid failure
3. The occurrence of increased play in the operation of the trapezoid

Read more: How is specific fuel consumption measured
? To make repairs or replacements yourself, you will need the following tool:

• Ratchet handles
• Extension
• Head for 10 and 13 mm
• Sharp knife or screwdriver
• Phillips screwdriver

Size of brushes for Lada Kalina, Priora, Granta cars

The wipers on these cars are not symmetrical.
On the driver's side they are 60 cm long, and on the passenger side - 40 cm. It is noteworthy that in this case the wipers cannot be replaced with larger ones. The rear clear has a length of 36 cm and also does not change. As for Lada Priora cars, their wipers are also not the same. On the driver's side they are 53 cm long, and on the passenger side - 50 cm. In this case, only passenger options are allowed to be changed. Those who wish can use smaller ones, 48 ​​cm long, or larger ones - 51 cm. As for the rear wiper, in this case it is smaller than that of the Lada Kalina - 33 cm.

Lada Granta cars have the same cleaners as the Lada Kalina. So the dimensions are as follows:

• driver's brushes – 60 cm;
• passenger – 40 cm.

To summarize, we note that windshield wipers for cars are very important, especially in winter, when it snows and the road is practically invisible. They are also needed during rain, in order to clean the windows and not interfere with visibility on the road.

No car is produced without these devices. In general, glass cleaners on modern cars do not differ much from older brands.

The only thing is that the technical characteristics of the new models are more advanced. Previously, brushes could only remove water from the glass, but now they are able to remove dirt, midges, snow, etc. Thanks to this, visibility is significantly improved. Modern wipers are resistant to even the most severe frosts. They are made from durable materials and are divided into winter and summer.

If the brushes are smaller than expected, then due to the small cleaning area, the overall level of efficiency of the windshield wipers will decrease. Plus, an island of dirt and water forms in the center of the windshield, which will significantly impair visibility while driving. Let us recall that in the previous article we looked at why the stove fan does not work and how to repair it yourself.

Size of windshield wiper blades for Lada Samara series cars (2115, 2114 and 2113)

These cars leave the factory with seven-fold windshield wipers, which are 51 centimeters long. If replacement is necessary, you can use a 53-centimeter-long windshield wiper for the driver's wiper, but on the passenger side you will have to leave a 51-centimeter-long blade, since if you install an extended wiper, a “waterfall” will form in the center of the windshield.

Note that Lada Samara cars also have rear wipers. Cars leave the factory with a windshield wiper 30 centimeters long, but you can install a blade 33 centimeters long - this will not cause any problems. Note that, if you wish, you can even install brushes 40 centimeters long, but you will need to move a couple of teeth on the wiper motor to adjust its stroke.

All models of cars produced by the AvtoVAZ automobile concern indicated in the title of this section of the article are the progenitors of the Lada Samara series. It is for this reason that their front wipers are symmetrical, just like those of their descendants, and have a length of 53 centimeters.

Lada Kalina windshield wiper blade size

Lada Kalina cars have non-symmetrical wipers. So, on the driver’s side the wiper blade is 60 centimeters long, and on the passenger side – 40 centimeters. At the same time, liberties with the size of the driver’s “wiper” are not allowed, but the passenger one can be increased to 41 centimeters. The rear windshield wiper blade on the Lada Kalina is 36 centimeters long.

https://www.youtube.com/watch?v=pl7_9CmEXq4

Lada Priora windshield wiper blade size

Lada Priora cars are equipped with asymmetrical windshield wiper blades. On the driver's side, the wiper is 53 centimeters long, and on the passenger side it is 50 centimeters long. As in the case of the Lada Kalina, liberties are allowed only with the passenger “windshield wiper”. You may notice a standard windshield wiper that is either 48 centimeters or 51 centimeters long. The rear wiper on the Lada Priora is 33 centimeters long.

Lada Granta windshield wiper blade size

Lada Granta cars inherited the glass cleaning system from the Lada Kalina car. In this regard, the length of the driver's windshield wiper is 60 centimeters, and the passenger's is 40 centimeters, but it can be replaced with a windshield wiper 41 centimeters long.

How to choose the right size of windshield wipers for a Lada Granta without compromising their quality?

Replacing brake pads with your own hands: how do you know when it’s time to change?
step-by-step instructions on how to replace brake pads on a car (90 photos) The safety of the driver and passengers primarily depends on the quality of cleaning the windshield, so every car owner must control this issue. Wipers are classified as consumables, so sooner or later every car enthusiast will be faced with the need to replace them. What size is the Lada Granta windshield wiper and in what cases do the blades need to be changed - we will tell you more about this below.

There are several signs that indicate that the purifiers need replacing:

1. The primary and most important is poor cleaning quality of the windshield, the appearance of streaks and streaks when fluid is supplied from the washer reservoir. As a result of wear of the blades themselves installed on the wipers, the quality of glass cleaning is reduced to a minimum. Poor cleaning results in obstructed visibility.
2. The appearance of noise and squeaking when the wipers operate. As a rule, extraneous noise appears after the brushes begin to wear out and the glass is poorly cleaned. But there are also cases when the sound appears first, and only then the ineffectiveness of the brushes. So if you notice squeaking or noise, keep in mind that you will have to change your wipers soon.
3. The glass began to darken. As a rule, darkening of the glass is caused by the use of a low-quality washer, but the reason may also lie in damage to the rubber blade. This will cause the angle of the wiper edge to be offset.
4. The windshield wipers seem to “jump”. As a result of an increase in lifting force, the following problem appears - the wipers begin to work faster, and accordingly, they can jump over some areas of the glass surface.

The brush does not adhere tightly to the glass surface

Brush sizes

Standard sizes of windshield wipers for Grant:

• according to the technical manual, the size of the driver's wiper is 600 mm;
• The size of the passenger cleaner is 410 mm.

Alternatively, you can use longer windshield wipers:

1. On the passenger side, you can install a longer wiper, its size should be no more than 450 mm, this will allow it to engage a larger amount of surface.
2. As for the driver's brush, it is better not to experiment here. For example, if you install a 610 mm wiper, this will cause it to touch the car body during operation, and accordingly, a knock will appear (video author - TheLadaKalina 2).

Types of wipers

There are two types of wipers for the Lada Granta:

1. Frameless. Such products are better pressed against the surface of the windshield, which allows for better cleaning. Due to the absence of a frame, such devices practically do not freeze during the frosty season, which greatly simplifies their operation in winter. In addition, when operating at high speed, frameless products produce an order of magnitude less noise.
2. Frame. This option is older, since it was previously widely used on many cars. Their cost is lower, but they are equipped with a frame, which in any case will freeze during cold weather. However, products of this type tend to cause less damage to the surface of the windshield, since they are not pressed against it as tightly, unlike frameless options.

There is also a hybrid version of the product, but it has the same characteristics as frame wipers, so we do not recommend choosing it. The most technologically advanced option is frameless products, but their cost is higher (the author of the video is the remgar channel).

Recommendations for selection

Let's consider several product manufacturers:

1. Frameless Bosch Aerotwin. Belgian-made products are equipped with native fastenings; the main advantage is a long service life, as well as aerodynamics and the absence of extraneous sounds during operation.
2. SWF VisioNext - also of the frameless type, equipped with a hook-type fastening. The products are manufactured by Valeo, which also produces many other types of components and parts for cars.
3. Bosch Twin Spoiler frame brushes. Dimensions fit standard Granta windshield wipers. Despite the fact that the products are frame, they are quite reliable and have a long service life.
4. Champion Aerovantage. This manufacturer has been on the market for quite a long time, during which time it has been able to win the trust of many of our compatriots. The products belong to the premium segment of the market and are equipped with a steel frame.

How to change rubber bands

You can replace the rubber bands yourself, which will save you money on buying new brushes. You will need pliers and a wide blade screwdriver. First of all, to replace the wiper blades on a Priora, you need to install them perpendicular to the arms, press the locking brackets and then pull them out. After removing the wipers, carefully bend the rubber band clamps located at the edges of the pressure plate to a minimum angle. This is done so that the rubber can easily come out of the wiper. It is better to bend the clamps with pliers, as there is a risk of damaging the clamps.

After the rubber band is removed from the clamps, you need to pull out the metal plates that hold the curved shape. You should immediately remember the directions of the bends of the plates so as not to confuse them and not to do the work again, since the elastic band will not be pressed tightly against the windshield. The plates have recesses where the rubber grooves should fit. There are situations when the thickness of the groove is greater than the width of the opening. In this case, it can be expanded with a thin file.

Read more: STS number of the car, what is it?

The rubber band is easily inserted into the latches until it clicks. At the same time, it should not play, otherwise it will quickly wear out. If the installed rubber band leaves uncleaned areas on the glass, it must be replaced again. However, it is worth considering that the cost of several tapes damaged during installation may be more than the cost of the assembled wiper.

How to choose the right size of windshield wipers for a Lada Granta without compromising their quality?

How often should you change antifreeze?

The safety of the driver and passengers primarily depends on the quality of windshield cleaning, so every car owner must control this issue. Wipers are classified as consumables, so sooner or later every car enthusiast will be faced with the need to replace them. What size is the Lada Granta windshield wiper and in what cases do the blades need to be changed - we will tell you more about this below.

There are several signs that indicate that the purifiers need replacing:

1. The primary and most important is poor cleaning quality of the windshield, the appearance of streaks and streaks when fluid is supplied from the washer reservoir. As a result of wear of the blades themselves installed on the wipers, the quality of glass cleaning is reduced to a minimum. Poor cleaning results in obstructed visibility.
2. The appearance of noise and squeaking when the wipers operate. As a rule, extraneous noise appears after the brushes begin to wear out and the glass is poorly cleaned. But there are also cases when the sound appears first, and only then the ineffectiveness of the brushes. So if you notice squeaking or noise, keep in mind that you will have to change your wipers soon.
3. The glass began to darken. As a rule, darkening of the glass is caused by the use of a low-quality washer, but the reason may also lie in damage to the rubber blade. This will cause the angle of the wiper edge to be offset.
4. The windshield wipers seem to “jump”. As a result of an increase in lifting force, the following problem appears - the wipers begin to work faster, and accordingly, they can jump over some areas of the glass surface.

The brush does not adhere tightly to the glass surface

Brush sizes

Standard sizes of windshield wipers for Grant:

• according to the technical manual, the size of the driver's wiper is 600 mm;
• The size of the passenger cleaner is 410 mm.

Alternatively, you can use longer windshield wipers:

1. On the passenger side, you can install a longer wiper, its size should be no more than 450 mm, this will allow it to engage a larger amount of surface.
2. As for the driver's brush, it is better not to experiment here. For example, if you install a 610 mm wiper, this will cause it to touch the car body during operation, and accordingly, a knock will appear (video author - TheLadaKalina 2).

Types of wipers

There are two types of wipers for the Lada Granta:

1. Frameless. Such products are better pressed against the surface of the windshield, which allows for better cleaning. Due to the absence of a frame, such devices practically do not freeze during the frosty season, which greatly simplifies their operation in winter. In addition, when operating at high speed, frameless products produce an order of magnitude less noise.
2. Frame. This option is older, since it was previously widely used on many cars. Their cost is lower, but they are equipped with a frame, which in any case will freeze during cold weather. However, products of this type tend to cause less damage to the surface of the windshield, since they are not pressed against it as tightly, unlike frameless options.

There is also a hybrid version of the product, but it has the same characteristics as frame wipers, so we do not recommend choosing it. The most technologically advanced option is frameless products, but their cost is higher (the author of the video is the remgar channel).

Recommendations for selection

Let's consider several product manufacturers:

1. Frameless Bosch Aerotwin. Belgian-made products are equipped with native fastenings; the main advantage is a long service life, as well as aerodynamics and the absence of extraneous sounds during operation.
2. SWF VisioNext - also of the frameless type, equipped with a hook-type fastening. The products are manufactured by Valeo, which also produces many other types of components and parts for cars.
3. Bosch Twin Spoiler frame brushes. Dimensions fit standard Granta windshield wipers. Despite the fact that the products are frame, they are quite reliable and have a long service life.
4. Champion Aerovantage. This manufacturer has been on the market for quite a long time, during which time it has been able to win the trust of many of our compatriots. The products belong to the premium segment of the market and are equipped with a steel frame.

What is a trapezoid: design and signs of the need for replacement (repair)

A trapezoid on a car is a drive mechanism consisting of a system of rods and levers that perform reciprocating movements, moving the windshield wiper blades. On most cars, including the Lada Priora, such devices are located in a niche under the windshield.

With the help of a trapezoid, reciprocating movements are created. This is achieved precisely with the help of a special device circuit. Below is the design of the Priora trapezoid.

In addition to creating reciprocating movements, the trapezoid also performs another important function. With its help, the wipers move synchronously to clean the windshield. The malfunction of this mechanism leads to the operation of the wipers being disrupted. If malfunctions occur, the device must be repaired. The ability to repair depends on the type of damage. Most often, hinge joints fail, which can be replaced using a repair kit. If they are in good working order, then when removing the trapezoid, they must be lubricated.

If the integrity of the threaded connections is compromised or parts of the levers and rods are damaged, then the trapezoid must be replaced. Determining the malfunction of the device is not difficult. Defects can be identified by a number of characteristic signs:

• slow operation of windshield wipers;
• the wipers do not work at all or only one of the two wipers functions;
• intermittent and jerky movement of the brushes, which may indicate souring of the driver drive in the bushings (which is why they must also be lubricated).

It is necessary to dismantle the trapezoid and repair it in any of the above cases. Excessive load negatively affects the operation of the gearmotor, which can simply burn out due to overheating. That is why pay due attention to the device if there are signs indicating a malfunction.

Dimensions

It should be noted: a feature of this car is the ability to install custom-sized wipers. If the length is more than 508 mm, no difficulties will arise. The following sets of pairs of brushes can be installed:

• 550 mm + 500 mm;
• 530 mm + 530 mm;
• 530 mm + 510 mm;
• 530 mm + 500 mm.

The operation process itself usually does not cause problems. But you need to remember that the increased weight, length and generally non-standard design have a greater impact on the gearbox, engine and slots - on which the leads are installed. Long-term increased load, especially at high speed, can lead to rapid wear of the splines. Or failure of the electric motor.

Original articles

AvtoVAZ, like many other car manufacturers, does not independently manufacture small parts. Including brushes. The official supplier of VAZ wipers until 2021 is Bosch. The products of this company are supplied to the AvtoVAZ plant. After which it is packaged in original boxes.

But it should be noted that purchasing original components does not affect the warranty. No problems during installation, as well as during operation, are also guaranteed

It is only important to carefully examine the box. Because there are a lot of fakes on the market. Windshield wiper blades have the following part numbers:

Windshield wiper blades have the following part numbers:

Replacement options

Finding and purchasing original windshield cleaning blades is not a trivial task. It is much easier to purchase high-quality analogues

It is only important to pay attention to the article number, as well as the length. The cost varies depending on the brand, quality and type of brushes themselves. The following varieties are presented on the market in the Russian Federation for 2021:

The following varieties are presented on the market in the Russian Federation for 2021:

The following varieties are presented on the market in the Russian Federation for 2021:

• frame;
• frameless;
• hybrid;
• winter.

Frame

Frame modifications are also often called classic. They have an important drawback: at high speed, due to an unsuccessful aerodynamic shape, the degree of cleaning is significantly reduced. But some models are equipped with a special spoiler. Due to this, air resistance is reduced. The advantage of frame brushes is their low cost.

Frameless

Frameless ones are made of a single piece of rubber. This makes it easy to clean the surface of the windshield even at high speed. Air resistance will be minimal. The cost of wipers of this type is slightly higher than frame ones. But they are more convenient to use. Removing and replacing old brushes of any type with new frame ones will not be difficult.

Hybrid

Hybrid wipers combine the advantages of frameless and frame models. They are brushes made entirely of rubber. But having a rigid frame made of metal or other materials. They do a good job of cleaning the windshield even at high speed on the highway. This applies to both normal precipitation in the form of rain or snow. So does dust and road dirt.

Winter

Winter wipers are distinguished by their elasticity - even at sub-zero temperatures they clean the glass well

But it is important to remember that their price is usually an order of magnitude higher than regular ones. Because they are more expensive to produce. In this case, to avoid rapid wear of such parts, you can purchase them as replacements.

And install only in difficult weather conditions. For example, in winter

In this case, to avoid rapid wear of such parts, you can purchase replacement parts. And install only in difficult weather conditions. For example, in winter.

How Priora wipers should work correctly

Lada Priora wagon Breaking bucket. › Logbook › Repair of wipers. Replacing the windshield wiper motor.

A couple of days ago, driving out of the yard, I waved my wipers and they froze in the middle of the glass. That day I did just that, the frosty weather allowed.

For diagnostic purposes, dancing around the car at minus twenty degrees was used, as well as a huge amount of swearing. As a bonus, he sent curses to the designers of AvtoVAZ. The diagnostic results showed that two small gears were worn off in the motor.

I made attempts to find gears for sale. I called and went to several large stores, with zero results. The toad continued to choke me, so I started calling for a showdown. The tens and sevens probably have everything, but the Priora has nothing. Have not found. The price of the motor during disassembly was announced at 700 rubles, but it is not available. I bought a new one for 1430 rubles. This KETZ is different from the native one. Well, he looks black. My rod is 10mm. Put. It works very well, but the modes are mixed up.

In my native language it was - first an intermittent mode, then just non-stop, and the last one was fast. The new one is wrong. Also, first intermittent, then wildly furious which I don’t use, and the last at normal speed without stopping. That is, the second and third are swapped. You can, of course, swap the two wires, but you don’t want to take it apart again.

And the most frightening thing is how to remove all this stuff for replacement. There are plenty of instructions on the Internet, I will describe a couple of points. I did not remove the expansion tank platform. I just couldn’t unscrew it; everything in the arch was frozen. I unscrewed two bolts near the glass and bent this pad in all directions, it was quite soft. Car with Panasonic air conditioning. Therefore, the passenger wiper rod rests against the stove. I tried setting the wipers vertically, but it still won't fit. He used brute force. Using the handle of a hammer, I “expanded” this gap and pulled through the trapezoid. I tried to disassemble the trapezoid, it also helps. The rod on which the wiper arm is attached can be easily pulled out. There is a lock washer, it is pryed off with a flat screwdriver and the rod comes out quite easily.

Wipers for Lada Granta dimensions

Foreign manufacturers indicate the length of the windshield wiper in inches, so the suitable length for a passenger blade is 16″. Sixteen inches - 406 mm, probably because of this, brushes with lengths of both 40 and 41 cm can be installed on the right side of the Granta. If desired, you can install a passenger windshield wiper up to 45 cm, but I would recommend staying in the range of 400...410 mm.

I have added brush article numbers to the selection: they will help you find specific products in stores that sell auto parts (this is faster and, most likely, cheaper). Also, the articles will allow you to avoid compromises in the form of several centimeters in the length of the brushes - choose only what is made specifically for your car.

Finally, a comparison of prices for windshield wipers.

Frameless wipers on Granta

An excellent option is the Bosch Aerotwin kit (code - AR601S, article number - 3397118907). This is a set of brushes with a length of 600 and 400 mm, which are produced in Belgium, with a “native” and single fastening. They clean perfectly, do not creak, are durable, and aerodynamic. Read more about the Bosch Aerotwin line.

A good option is two SWF VisioNext brushes: 600 mm (code - 860, article number - 119860) and 400 mm (code - 840, article number - 119840). These wipers are also designed to be mounted on a “hook”. SVF is part of the Valeo group; windshield wipers are produced in Poland and France. Read more about SWF wipers.

An available option is two brushes from the St. Petersburg company Horse Ballistik, 60 and 41 cm. When installing, you will have to use an adapter for attaching the “hook”. If you are offered a choice when purchasing, take the option with a rubber tape - it squeaks less.

Hybrid wipers for Granta

An excellent option is a pair of Denso Hybrid brushes: 600 mm (article number - DUR-060L) and 400 mm (article number - DU-040L).

Denso wipers are a modification of frame windshield wipers, covered with an aerodynamic casing on top.

Frame wipers for Granta

Take a look at the pair of Champion Aerovantage single wipers: 600 mm (ref. A60/B01) and 400 mm (ref. A41/B01). Champion Aerovantage - premium quality brushes with a full metal frame

A good option is a set of frame wipers Bosch Twin Spoiler 601 S (article - 3397010297), which can accommodate a pair of 600+400 mm. Reliable frame wipers with spoiler, made in Belgium.

Radiator grill VAZ 2107 chrome

Finally, I would recommend perhaps the most inexpensive frame windshield wipers with a famous brand - a pair of Bosch Eco frame wipers: 60C (3397004673) and 40C (3397004667).

Lada Priora Sedan =Silver Edition= › Logbook › Wiper leads from Niva Chevrolet

Hello everyone =)
The idea to change the wiper arms has been around for a long time, since the arms of the pre-restyling Prior look very bulky and awkward, and my problem was that the spring on the passenger arm was weakened and the frameless brush did not clean the middle of its half of the glass.

I really wanted to find leashes from Master Sport

with 2 springs (article
21235205065PCSMS
), but it turned out to be impossible to find them: neither Emex nor Exist had goods under this article in stock and were not expected in the near future.
I had to take an analogue with one spring from , which, as I understand, are used on Chevrolet Niva cars.

There’s nothing to write about replacement and installation; it’s better to post a couple of photos of how the new leashes are installed =)

Unfortunately, replacing the leashes brought not only positive emotions in the form of getting rid of huge sabers and improving the quality of cleaning, but also a slight disappointment: despite the noticeable difference in the quality and speed of glass cleaning, the passenger frameless brush still refused to pass through the middle of its half of the glass , as well as the appearance was spoiled by the nuts for securing the leashes visible from under the hood (due to their slightly different design). Plastic plugs for the nuts, which I ordered from AliExpress, helped me cope with the last task.

The plugs are supplied in sets of 10 pieces. For the nuts securing the leads, we select plugs for M8 threads. I am attaching a link to them: ru.aliexpress.com/item/32…62bab4854af46a826e35e10fe

I also used the remaining plugs to cover the nuts securing the strut to the front suspension shell, otherwise it felt like they were missing right here =)

The issue with cleaning the passenger side was resolved by temporarily replacing the wipers with frame ones - with them everything is cleaned with a bang, but, closer to winter, you will still need to purchase and switch to “frameless” wipers, so I will be happy to listen to your advice on choosing frameless wipers on Priora =) Thank you all for your attention and good luck on the roads and in life!

source

Video of installing wipers on Priora

Look at an example of installing Bosch Aerotwin brushes with a hook mount:

The length of the windshield wipers on the Lada Priora on the driver and passenger sides is 20″ (508 mm), the rear ones are 13″ (330 mm).

Standard sizes of wipers on Lada Priora:

The size of brushes for Lada Priora depends on their location and the type of car body.

Wiper parameters for hatchback and station wagon:

• Length of driver's windshield wipers: 508 mm (20″).
• Passenger wiper length: 508 mm (20″).
• Rear wiper length: 330 mm (13″).

Windshield wiper parameters for a sedan:

• Length of driver's windshield wipers: 508 mm (20″).
• Passenger wiper length: 508 mm (20″).

Important: the rear wiper is not included in the factory equipment of the Lada Priora sedan. If necessary, the original frame wipers for this Lada model can be replaced with alternative sizes - 530 and 510 (mm), 550 and 500 (mm) or 630 and 480 (mm)

Increasing the size allows for better glass cleaning

If necessary, the original frame wipers for this Lada model are replaced with alternative sizes - 530 and 510 (mm), 550 and 500 (mm) or 630 and 480 (mm). Increasing the size helps to clean the glass better.

Possible sizes of wipers on the driver's side for Lada Priora of all years of production.

Data in inches.

Possible sizes of wipers on the driver's side for Lada Priora of all years of production.

Data in inches.

Possible sizes of rear wipers for Lada Priora of all years of production.

Possible sizes of wipers on the driver's side for Lada Priora of all years of production.

Data in inches and (mm).

Possible sizes of wipers on the driver's side for Lada Priora of all years of production.

Data in inches and (mm).

Possible sizes of rear wipers for Lada Priora of all years of production.

Data in inches and (mm).

FakeHeader

Comments 20

It's strange how they fit in with you? I had a 51 cm passenger side that touched the plastic along the edge of the glass. Right now I set the driver’s to 54-53 and the passenger’s to 47, everything is fine... but 56 won’t fit there...

On a Priora, the wind slats get in the way, but I have a Ten-Prior.

How is this “ten-prior”?

At first it was just 2110. And then it started! Nowadays, the Priora’s filling is luxury, but not everything is finished yet. Read the introduction to the blog.

My driver's license is 53 and the other is 50. It won't fit anymore.

The wind slats interfere with the Priora.

I thought you didn’t check the prior...

I seem to have these from the factory, if I'm not mistaken))

The dealer could have supplied it or you are mistaken.

Look at my main photo, it looks the same)

I have 54 cm and they barely climb on top of each other, but your 56 cm is probably a lot

I don’t know how he “climbs a little,” but everything works well for me.

Not. They also work great, I mean, when not working, the left brush rests slightly on top of the right one.

This means it is not installed correctly, it must be placed in the lower position.

I put it in the lower position, I have frameless ones, there are no two positions on the bracket, only in the middle. Anyway, the factory recommends 50 cm, no more.

We replace the brushes when the quality of windshield cleaning deteriorates, approximately once a year - preferably before the start of the autumn-winter period. The length of both windshield wiper blades is 500 mm. When purchasing imported brushes, you should focus on the size of 20′ or 510 mm. If the brushes are very dirty or covered with ice, they should be removed and cleaned. Brushes should be washed periodically under the tap with warm water and soap.

Be careful when removing the brushes: the lever under the action of the spring may suddenly drop onto the glass and break it. To do this, move the lever with the brush away from the windshield.

By pressing the brush locking tab...

...move the brush from the hook of the lever so that the brush lock comes out of the hook.

Remove the brush from the lever. If you need to replace the brush retainer, move it from the brush axis and remove it. Similarly, remove the other windshield wiper blade.

Read more: Daewoo nexia on-board computer

Frameless type brushes can be installed on the car. Install the brushes in reverse order.

Windshield wipers, wipers, brushes - all these are elements of one device on a Priora car. They help the driver clear the windshield from raindrops and melting snow. There are many manufacturers on Priora whose brushes fit the car without any problems. Read the article to the end and find out the full list and prices of manufacturers. Let's say the following: the average price starts from 300 rubles. The quality of their work is specified in technical regulations, but even the driver himself will not be happy if the wipers do not clean the glass well - driving blindly is dangerous. The Priora car has three wiper speed modes - which helps cleaning in any rain. To clean the rear window, a rear wiper is installed on three car bodies. The sizes of wipers on Priora are the same in all bodies: hatchback, station wagon, sedan.

The windshield wipers on the Lada Priora have to be changed periodically, just like in any other car. New elements of the cleaning device are chosen with special care - it is easier to buy a good pair so that it works for a long time, for an above-average amount, than to constantly buy the cheapest one, being nervous because the wiper blades do not clean anything.

If the wipers on the Lada Priora do not work, this is a reason to understand the system and try to correct the situation. There may be several reasons: freezing to the glass, the wiper wiring is shorted, or the wiper motor simply cannot cope with the resistance - I’ll tell you more about this later. Thank God on a Priora car this is, firstly: not a common problem, and secondly, the price of the motor starts from 2500 rubles. If the brushes are not working, it is recommended to travel by vehicle only in dry weather without precipitation or slush. If the size of the windshield wipers of a Priora car does not suit the owner, he can try installing non-standard windshield wipers to improve visibility on the road. In driver communities and from personal experience, I can say that this part sometimes scratches the glass, but this is all because it rarely changes - change them every season and there will be no scratches on the glass.

Replacing the windshield wiper motor on a Priora

To replace the wiper motor itself, you must first note the position of the trapezoid bar relative to its body, so that later you can install everything in the same order.

Unscrew the three motor mounting bolts:

And the central nut using a 13 mm wrench. We remove the motor and replace it with a new one if necessary.

Installation occurs in reverse order. The price of a new trapezoid is from 1000 rubles for the original one produced by AvtoVAZ. You will have to pay at least 2000 rubles for the motor.

Wiper blade sizes for VAZ: Priora, Lada Kalina, Largus

To drive a car safely, you need a good overview, so it is very important to select the right VAZ windshield wiper (windshield wiper) blades for your car. Next we will tell you:

• what is affected by the length of the brushes;
• how to select brushes by length;
• what is the size of brushes for VAZ cars: Priora, Lada Kalina, Largus.

What does the length of the brushes affect?

The shape of the front glass is selected based on parameters such as the size of the car and the effect of glass on aerodynamic resistance. Therefore, both the height and width of the glass on cars of different brands and models differ. Therefore, the length of the wiper blades suitable for these cars also differs. After all, the windshield wiper lever is selected in such a way that, when in a completely vertical position, its tip falls at the center of the height of the glass. In this case, properly selected wiper blades run almost flush with the seal at the top and level with the dashboard at the bottom, allowing the blades to clean the area that gives the driver maximum visibility.

How to select VAZ brushes by length

The easiest way to find brush sizes is in the car's operating instructions. If you do not have such instructions and you cannot download them on the Internet, then remove the old brushes installed on your car and measure their length. It often happens that a person bought a car, but it has inappropriate brushes installed and there are no operating instructions. In this case, we recommend doing the following:

• place the windshield wiper arms vertically;
• measure the distance from the attachment point to the rubber seal;
• subtract 5 mm from this distance and multiply by 2, this will be the length of the brushes.

This technique can be used not only for the front brushes, but also for the rear brushes. On many machines, the lengths of the right and left brushes are different, so their optimal length can be found in the operating instructions or on the forums of the owners of such machines, for example:

1. Scorpio club https://www.souleyman.ru/forum/viewtopic.php?p=279085.
2. Opel Omega Club: https://www.opel-omega.ru/index.php?showtopic=9896.
3. Drom https://forums.drom.ru/toyota-caldina-carina-corona-premio-allion-avensis/t1151162577.html.

Brush sizes for VAZ cars: Priora, Lada Kalina, Largus

We have compiled a table that includes the dimensions of all popular cars produced by AvtoVAZ:

vipwash.ru

Standard size of wipers for Lada Priora

The standard equipment of the Priora comes with standard windshield wipers, the size of the blades is:

• on the right and left wipers of the Lada Priora sedan - 508 millimeters;
• on the rear windshield wiper, which is used in station wagon or hatchback cars, - 330 millimeters.

The standard windshield wipers of all Priora models work quite well, but many car enthusiasts are dissatisfied with the area that does not clear and remains right in the center during snowfall or heavy rain. To fix this problem, they install an extended length windshield wiper. If you are interested in this possibility, the maximum dimensions of the wipers will be as follows:

• 630 millimeters for a brush located on the driver’s side of the vehicle;
• 480 millimeters for the wiper on the passenger side of the windshield.