Load capacity of the trunk of a VAZ 2107

trunk dimensions of vaz 2107

Comments 7

How high is the inner shelf where the speakers are? is it 540-170?

there's only a trunk here

You did not understand. There is a niche in the trunk under the speakers. Where is the gas cylinder usually placed? you still have the width 275 written

yes it turns out like this 540 -170

To the ribs of the trunk lid? Or until what exactly? Otherwise, I have a false floor by 16 cm. And the sub took 37 cm. We get 53 cm. And for some reason it doesn’t fit by 2 cm. How is that?

The luggage compartment is an integral part of every car, where you can transport various loads commensurate with the carrying capacity of the car. The trunk of the seventh model Zhiguli initially has no sound insulation, no attractive finish, no convenient lock control, which forces the owners of this car to think about modifications of various kinds.

Electrical equipment VAZ 2107

Dimensions 2114. all VAZ cars. Dimensions, body dimensions, available engines and configurations

Wiring type: single-wire, negative on the car body (ground).

Battery: 6ST-55, capacity 55 Ah. Batteries with a capacity of 60 and 65 Amperes are also suitable, but you need to check the dimensions. Usually it is 242 mm x 175 mm x 192 mm.

Operating voltage in the network: 13.6 -14.6 volts. The generator (G221) must deliver a current of no more than 1/10 of the battery capacity, i.e. approximately 2 to 5.5 Amps.

Ignition coil - B117 or B117-A (for carburetor engines) Starter - ST221

Lamp type:

— lamp for low and high beam: H4 or AKP2-60+55 (in Russian) — lamp for clearance and side turn signals: T4W or A12-4-1 — lamp for turn signals in the headlight, fog lights, reverse and brake lights: P21W or A12-21-3— license plate and interior lighting lamp: C5W or AC12-5-1

Video of BMW M760Li xDrive

Technical specifications BMW M760Li xDrive (2017)

• Body type: Sedan;
• Engine: 12 cylinders, 6.6 liters, Gasoline;
• Engine power: 600 l/s;
• Torque: 800 Nm;
• Maximum speed: 250 (305) km/h;
• Average fuel consumption: 12.6 l/100 km;
• Acceleration from 0 to 100 km/h: 3.9 s;
• Drive: Full ;
• Gearbox: 8-speed automatic transmission;
• Length: 5238 mm;
• Width: 1902 mm;
• Height: 1485 mm;
• Wheelbase: 3210 mm;
• Ground clearance (Clearance): 135 mm;
• Wheels: 20-inch;
• Trunk volume: 515 liters;

Review of VAZ 2106: Soviet classic

avtoexperts.ru

Clearance

, perhaps one of the most popular car characteristics requested by car enthusiasts. People are interested in the level of ground clearance of cars immediately after they know the volume and power of the engine, consumption and dynamic characteristics. And this is correct, because in our Russian conditions there is high ground clearance

A car is sometimes more important than having rear windows or even air conditioning. How to increase

ground clearance, in order to make driving a car on domestic roads more comfortable, we will tell you in this material.

Before you begin the operation of increasing the ground clearance of your car, Honor needs several aspects. First: accurately calculate the ground clearance of your car (since its value may differ from the passport value, especially if it is a foreign-made car). Second: decide what ride height you want to achieve. The point is that just increase

Ground clearance is still half the battle, but you need to take into account such parameters as departure/entry angles and the vehicle's longitudinal flotation angle. They are different for all cars, and even if you increase the ground clearance of your sedan, it will not become an SUV, it will not be better to climb hills - and all because of its geometric cross-country ability specified by the factory designers. And, finally, you will have to decide on the budget for this operation, since there are several ways to increase clearance, and the labor costs for their use are different.

FakeHeader

Comments 106

And when you take out the spare tire, doesn’t the wing interfere?

How will it interfere if you put it on yourself and up. Of course, it takes longer than usual to pull out the spare tire, but you don’t carry it every day

done perfectly. I think there will be a lot of dust, and it will be difficult to remove it

nice and neat)

uh, sedans don’t even have a boot, but here the last hint of it is mercilessly killed.

but I don’t drive anything there)

I don’t understand at all why you need a car that doesn’t carry anything except your ass.

but I have a car for transporting goods)

The VAZ 2102 (2104) will help you with this, it will have a larger trunk)))

but I don’t drive anything there)

Tuning

LADA-2107, along with other “classic” models, is one of the most tuned Russian-made cars. Its cheapness, on the one hand, and outdated design, on the other, force many owners over time to make efforts to modernize the car.

For example, installing hydraulic compensators on the engine results in a noticeable reduction in engine noise and an increase in timing belt life. We also offer ready-made kits for replacing rear drum brakes with disc brakes.

Due to the large volume of classic cars in use, manufacturers of spare parts offer a lot of finished industrial products to improve consumer properties, and even conveyor suppliers offer “improved” products to replace their own components (for example, a heater motor on bushings from the factory - change to a motor with bearings). The “classics” segment probably has the widest selection of spare parts that differ from the factory equipment.

Machine weight characteristics

For its time, the VAZ 2107 was an excellent car that was successfully sold, including outside our country. The machine's technical characteristics were not inferior to its analogues at a lower price; the design scheme used is highly reliable. The weight of the equipped vehicle is just over a ton, which allows it to demonstrate good power capacity.

The maximum permissible load is 400 kg, in other words the car can carry five adult passengers. If the quantity is smaller, luggage can be transported in a special compartment. A rational distribution of masses between the axles ensures good stability and controllability of the vehicle.

The small dimensions of the VAZ 2107 model, optimal weight for its size and a powerful engine provide the car with good dynamics and maneuverability. The successful design and low price predetermined the car's commercial success and, despite its advanced age, it still does not lose popularity.

Memo to the driver of VAZ 2107

This is a reminder for drivers of the VAZ 2107 (also relevant for other classics), I decided to create it because minor technical questions often arise, and it takes a lot of time to find the answer. And here everything is in one place. Save this reminder in your bookmarks or on your page on a social network, and use the social network buttons under the article for your health.

So, VAZ 2107 technical characteristics, dimensions, parameters.

VAZ 2107 was produced from March 1982 to April 2012. It has been produced in Egypt since 2006 to this day.

General view

ATTENTION! A completely simple way to reduce fuel consumption has been found! Don't believe me? An auto mechanic with 15 years of experience also didn’t believe it until he tried it. And now he saves 35,000 rubles a year on gasoline! Read more". The exterior of the “Seven” generally copies other VAZ models, called “classics”

On the other hand, some parts and components of the frame are not the same. They simply will not fit the general exterior due to the fact that they differ in basic parameters

The exterior of the “Seven” generally copies other VAZ models, called “classics”. On the other hand, some parts and components of the frame are not the same. They simply will not fit the general exterior due to the fact that they differ in basic parameters.

Let's start with the front. This area of ​​the car includes these components: the hood, the apron with the front bumper (they are considered more decorative elements) and the fenders.

As for the middle part of the car, this includes the roof of the VAZ 2107, sills, and doors.

Finally, the rear of the car includes the fenders, boot lid and rear apron.

All main body elements are made of stamped steel, additional ones are made of plastic. If minor damage occurs, they can be easily straightened and, if necessary, replaced with new ones without much difficulty.

Comparatively, the “seven” looks more modern than other “classic” models. It is for this reason that the car remained on the production line, although the designers did not make any significant changes.

The car interior is equipped with 4 seats. The front seats are made in the form of an independent adjustable design. As for the rear ones, they have no adjustment. The interior lining is plastic, the roof is covered with leatherette.

The interior of the “Seven” is structurally excellently protected from frontal and rear impacts, but a side collision with another car can lead to catastrophic consequences.

VAZ 2114

VAZ 2114 is a reliable five-door car. The capacity is 330 liters with the seats folded down, and with the seats folded down it is equal to 632 liters. The loading height of the side has an inconvenient level (similar to that used on the thirteenth model), which significantly complicates the loading process.

The dimensions of the trunk are as follows: length - 830 millimeters with the seats folded and almost 1660 millimeters with them unfolded, width - 935 millimeters, depth - 830 millimeters, height - 780 millimeters. These dimensions are approximate and are valid for models 2113 and 2114.

Transformation capabilities allow you to load items whose length and dimensions differ from standard dimensions. When installing additional luggage structures on the roof, you can transport a certain amount of large cargo.

The capacity, expressed in liters, is identical to the volume, which is indicated in cubic decimeters.

Hood of VAZ 2107

VAZ 2107 owners often modify the hood of the car. First of all, the lid stop, which was made at the factory in an extremely inconvenient way, changes. First you need to remove it from the latch and only then close it. On the VAZ 2106, the same stop is designed much simpler and more functional.

Installing an air intake on the hood

An air intake or snorkel is often installed on the hood of the VAZ 2107, which improves the appearance of the car and helps cool the engine. It is mounted so that air flows directly onto the air filter. Sometimes additional pipes are installed to the main air intake to increase cooling efficiency.

The snorkel is usually made by hand. In this case, it is better to use durable plastic or metal as a material. The air intake is mounted as follows.

1. A U-shaped hole is cut in the hood with a grinder.
2. The cut out part of the hood is bent to form the snorkel profile.
3. Triangular metal pieces are welded along the edges to cover the ends of the part.
4. The hood is puttied and painted to match the body color.

When cutting the hood, it is important not to touch the stiffeners provided by the design. Otherwise, the strength of the body will noticeably decrease

Hood lock

Sometimes car owners modify the hood lock of the VAZ 2107. If it does not work well or fails, the mechanism is dismantled. It is recommended to first outline the lock with a marker - this will avoid adjusting a new or restored lock. The mechanism is removed in the following order.

1. The hood opens.
2. The lock cable clamps come out of their seats.
3. The bent end of the cable is straightened with pliers. The fixing sleeve is removed.
4. Use a 10mm wrench to unscrew the lock nuts.
5. The lock is removed from the pins.
6. A well-oiled new lock is installed.

When replacing the cable, it is first disconnected from the lever handle. This is done from the salon. Then the cable is pulled out of its sheath. Nowadays, cables are often sold complete with a sheath. In this case, when replacing the old cable, it is pulled out along with the casing.

Trunk lock VAZ 2107

The luggage compartment lock of the VAZ 2107 has a simple design and fails extremely rarely, but sometimes it may be necessary to adjust or replace the mechanism.

Trunk lock malfunctions

Malfunctions of the trunk lock on Zhiguli cars of the seventh model are usually associated with malfunctions of the cylinder. In this case, the lock will need to be removed from the trunk lid and disassembled to replace the part. As for the adjustment, it is carried out when the luggage compartment lid does not close well or knocks while driving.

Trunk lock repair

To carry out repair work on the trunk lock, you will need to prepare the following list:

• wrench 10;
• installation;
• pencil;
• new lock or cylinder;
• Litol lubricant.

How to remove

To remove the luggage compartment lock, perform the following procedure:

1. Mark the position of the lock on the lid with a pencil.
2. Using a 10mm wrench, unscrew the 2 nuts securing the lock.

Replacing the larva

If the need for dismantling is due to replacing the cylinder, then before installing a new part, the mechanism is cleaned and lubricated with Litol. If the lock is completely replaced, the new parts of the product are also lubricated.

How to put

After lubricating the lock, it is installed in the following sequence:

1. Insert the sealing element into the luggage compartment lid.
2. Place the lock cylinder in the spacer sleeve.
3. Mount the cylinder together with the bushing into the lock.
4. Install the lock on the trunk lid in accordance with the previously made marks.
5. Fasten and tighten the mechanism with two nuts.

Video: replacing the trunk lock on a VAZ 2107

How to adjust the trunk lock

If the trunk lid lock on the “seven” closes with difficulty, it needs to be adjusted relative to the locking element. To do this, loosen the fasteners and change the position of the mechanism so that the latch easily fits into the body and the lever secures it well, and there is an equal gap between the luggage compartment lid and the body over the entire area.

Adjusting the trunk lid

Sometimes it becomes necessary to adjust the trunk lid. It happens that the part is located above the rear wings or is shifted to the right or left. If the trunk lid can be moved to the sides by unscrewing the fastening nuts on the hinges, then with an incorrect height position the situation is somewhat different.

To adjust the lid in height, you will need to open it completely and, holding the edge of the lid with one hand, apply force in the hinge area with the other. A similar procedure should be repeated on the other side.

The main thing is not to overdo it. Then close the lid and check the tightness of its fit. If necessary, repeat the procedure. To adjust the force of opening the trunk lid, the edges of the torsion bars of the springs are shifted to one of the teeth of the luggage compartment hinges.

Modifications of VAZ-2107

• VAZ-2107
  - engine 2103, 1.5 l., 8 cells, carburetor
• VAZ-2107-20
  - The model is completely identical in appearance to the VAZ-2107, but with a VAZ-2103 engine equipped with fuel injection (injector). Complies with Euro II standards.
• VAZ-2107-71
  - 1.4 liter engine, 66 hp. engine 21034 (21033-10) for A-76 gasoline. Compared to the 2103 engine, it has different characteristics and a reduced compression ratio due to the use of pistons from the 2108 engine. In addition, it is equipped with an ignition distributor with a modified characteristic of the centrifugal ignition timing regulator. version for China.
• VAZ-21072
  - engine 2105, 1.3 l., 8 cells, carburetor, timing belt drive
• VAZ-21073
  - 1.7 liter engine. 84 hp, 8 cells, single injection, catalytic exhaust gas converter - export version for the European market
• VAZ-21074
  - engine 2106, 1.6 l., 8 cells, carburetor
• VAZ-21074-20
  - engine 21067, 1.6 l., 8 cells, distributed injection
• VAZ-21076
  - Export version of the VAZ-2107 with the VAZ-2103 engine.
• VAZ-21077
  - The VAZ-2107 model is completely identical in appearance to the VAZ-2107, but with a VAZ-21011 engine (since 1994). Until 1994, the VAZ-2105 engine was installed on VAZ-21072 cars.
• VAZ-21078
  - Export version of the VAZ-2107 with a VAZ-2106 engine and a right-hand steering wheel.
• VAZ-21079
  - The VAZ-21079 model is completely identical in appearance to the VAZ-2107, but with a two-section VAZ-4132 RPD with a power of 140 hp. In 1997, a universal RPD appeared for rear-wheel drive and front-wheel drive VAZ VAZ-415. The cars were manufactured to order from the special services.

VAZ 2107 engines

The VAZ 2107 was equipped with several engines (for Russia and the USSR), these are:

Piston diameter and stroke:

– for 1300 = 79 mm x 66 mm – for 1500 = 76 mm x 80 mm – for 1600 = 79 mm x 80 mm – for 1700 = 82 mm x 80 mm

For carburetor VAZ 2107, DAAZ 2107-1107010 carburetors and their modifications were used. A-92 gasoline is used as fuel.

The injector for Euro-3 standards is already designed for A-95 gasoline.

Spark plugs for VAZ 2107:

Oil for VAZ 2107:

Oil change is done once every 10,000 km

VAZ 2107 body repair

Almost all experienced VAZ 2107 owners know the technology of body repair. This allows them to save on service station costs and extend the life of the body. The repair involves a number of measures to improve and modernize the skeleton.

For body work you will need the following tools.

1. A chisel with a sharp tip.
2. Bulgarian.
3. Clamp or pliers for holding new parts in place before welding or bolting.

Installation of plastic wings on a VAZ 2107

The main task of the wings is to protect the interior from dirt and stones entering through the open glass when driving. In addition, they improve aerodynamics. It is the wings of many cars that are most often restyled and take on a more streamlined shape. The wings of the VAZ 2107 are an element of the body and imply the presence of an arched cutout for the wheel. They are attached to the body by welding. Sometimes, to reduce the weight of the car, the front metal fenders are replaced with plastic ones. Moreover, plastic is not subject to corrosion. On the other hand, plastic fenders are less durable and may break in a collision.

1. Use a sharp chisel to disconnect the wing at the welding points.
2. Pull out the wing.
3. Using a grinder, clean off the remains of the wing and welds remaining on the body.

To install a plastic wing, you need to perform the following steps.

1. Apply a layer of special automotive putty to the joints between the plastic fender and the body.
2. Secure the plastic fender with bolts.
3. Wait for the putty to harden.
4. Remove the mounting bolts from the wing.
5. Remove excess putty from the edges of the wing that was squeezed out during installation.
6. Lubricate the wing with a layer of graviton and laminate.
7. Putty the entire structure and paint it in body color.

Video: replacing the front wing of a VAZ 2107

I would not recommend installing a plastic fender. Yes, it allows you to lighten the body, but at the slightest collision of the car with other cars, you will have to change the part again. Many Japanese, Korean and Chinese cars have such plastic parts installed. Any minor accident forces the owner to order expensive repairs.

Welding the body of a VAZ 2107

Typically, damage to the body of the VAZ 2107 is associated with corrosion or is a consequence of an accident. In these cases, it is optimal to weld with a carbon dioxide semi-automatic machine, which uses wire to connect individual elements. Electrode welding is not recommended, since it is almost impossible to make a high-quality seam on the body with its help. Moreover, electrodes can burn through thin sheets of metal, and the device itself is large and does not allow working in hard-to-reach places.

Threshold repair

It is recommended to begin restoring thresholds by inspecting the door hinges. If the doors are sagging, it will be extremely difficult to establish the correct gap. It is also inappropriate to restore an old threshold corroded by rust - it is better to immediately replace it with a new one. It is recommended to perform the work in the following order.

1. Cut off the outer part of the threshold with a grinder or chisel.

When welding a threshold, you must perform the following steps.

1. Weld the reinforcement with two parallel seams - first from below, then from above.
2. Thoroughly clean the weld seams to a mirror shine using a grinder.
3. Try on the outer part of the threshold. If there is a discrepancy, trim or bend.
4. Remove transport soil from the new threshold.
5. Coat the inside of the threshold with an acid or epoxy compound.
6. Secure the threshold with self-tapping screws.
7. Hang the doors.
8. Check the gap size.

The new threshold must be located strictly in the door arch, not protrude anywhere and not drown. After a careful inspection of the gap, welding of the outer part of the threshold begins, doing this from the middle pillar in both directions. Then the threshold is primed and painted to match the body color.

Video: replacing thresholds and repairing pillars of a VAZ 2107

My brother-in-law is a bodyworker

He always advised me and my friends to pay attention to the thresholds. “Remember, the car is rotting from now on,” Vadim said, lighting a cigarette during a break, pointing with a yellow finger at the bottom of the doors

I was convinced of this from the experience of operating the “Seven” when I was repairing the body. The thresholds were completely rotten, although the remaining areas remained untouched by corrosion.

Underbody repair

The underbody is more exposed to aggressive environmental influences and mechanical damage than other elements. The poor condition of the roads also has a noticeable impact on its wear and tear. Therefore, the bottom often has to be completely digested. You can do this yourself - all you need is an inspection hole or overpass and good lighting to inspect the bottom. Tools you will need:

• gas welding or semi-automatic welding machine;
• metal scissors;
• Bulgarian;
• straightening hammers.

Useful information about the "seven"

VAZ 2107 body length

The weight of the “seven” is exactly 1030 kilograms. At the same time, the car body is the heaviest among all other parts and components (600 kg). Its assembly diagram differs in a standard, classic sequence for VAZs and includes the following elements:

• Front end parts along with fenders, complemented by reinforcements;
• Roof;
• The bottom is also well reinforced, especially in the front and rear;
• Sidewalls.

Each of the parts is made from a special type of steel, has its own ID number, a specific mold and casting pattern. So, the roof of the “seven” always has a thickness of 0.9 mm.

The body parts are combined with each other by welding. If elements, for example, such as the floor, bear a significant load, they are additionally strengthened by arc welding.

In addition to the main elements, the body of the “seven” also has attached parts called “tails”. These are the parts that can be connected with bolts and hinges to the main frame - bumpers, hood, and so on.

Regardless of the configuration, the VAZ 2107 has certain dimensions.

The body length of the VAZ 2107 reaches 4126 mm, the width is 1620 mm, and the height is 1435 mm.

Control dimensions or correct body geometry

It is not enough for the owner of the “Seven” to know only the standard parameters of the car. It will also be useful to study the control body dimensions of the VAZ 2107 or the points of the car’s frame, especially if the owner plans to improve the dynamics of the car by lightening the body.

The diagram below shows the main control dimensions of the VAZ 2107.

Body dimensions geometry VAZ 2107

The same diagram shows how to check the control points of the body floor.

Control dimensions of the body of the VAZ 2107 floor

Control of the geometry of the body and the attachment points of the chassis and floor units is carried out on a special installation. This is a special type of machine designed for body inspection and repair. This is what he looks like.

VAZ 2107 body control dimensions and their correction

On such a machine, not only measurements are carried out, but also further editing of the body. The purpose of the operation is to recreate the original linear dimensions of the body.

ID VAZ 2107

On the “seven”, like other cars, individual technical information is indicated. It is presented in the table, which can be found under the hood.

IDs imply information not only about the car model. This contains detailed information about the body number and its weight.

Luggage rack manufacturers

Gutter racks have been produced since USSR times. But due to the bowl-shaped shape and the small number of points of contact with the load, Soviet designs have sunk into oblivion. Although they can be found today as a rarity or an “unkillable” platform for transporting agricultural products.

A typical representative of that era is the BelAZ gutter rack, which is still produced in Belarus to this day. Options for four and six supports differ slightly in load capacity. The total figure is 50 kg. Dimensions 1.3x1.05x0.21 m. Cost 1,200 and 2,500 rubles depending on the number of supports. Consists of 4 single and 4 paired black metal tubes. They occupy transverse positions. Perforated silver plates are screwed to the ends as side edges. The trunk's potential is limited by design.

Luggage basket made by BelAZ

Currently, luggage devices are made of lightweight, durable alloys using an anti-corrosion coating.

• from Rostov-on-Don is popular for its universal designs, but does not shy away from mounting on gutters. The basic model consists of six parts:
  Paw. Part of the support from the roof side.
• Clamp. Second part of the support.
• Pipe crossbar. It is made of square steel profile.
• Plastic plug. Before threading the crossbar into the rack, the plug is removed from the crossbar.
• Wing with nut. Main fastener.
• Rubber backing. She puts it on her paw.

Load capacity 70 kg. Price from 450 to 900 rubles depending on the length of the crossbars. An excellent budget option, but at speed it shows poor aerodynamics - it is noisy.

• The Ant trunk is no different in appearance from the previous one. But the price of 1,750 rubles is explained by a 2-year warranty.
• The Russian aerodynamic trunk consists of wing-shaped crossbars 8 cm wide and 125 cm long. They can withstand loads of up to 75 kg. A T-shaped groove for connecting accessories and corrosion protection will cost 3,520 rubles. The VAZ-2107 is not a weak car and, having high-speed characteristics, will only improve them due to the aerodynamic cross members.

Luggage baskets are installed on the Semerka. They create the necessary volume for small-sized personal items. But boxes on 2107 are a rare phenomenon. If only this is a car that has undergone exterior tuning. Then the shape of the airbox is combined with the curves of the car.

Video about installing a roof rack on gutters

At the end, two main rules should be added for installing luggage accessories on the drains of a VAZ-2107:

1. Maintain alignment from the windshield and rear window.
2. Tighten bolted connections evenly.

And also take care of the roof and operate the trunk in accordance with the instructions.

Roof rack VAZ 2107

If the “seven” is often used to transport various cargoes, then, as a rule, the standard trunk is not enough. In this case, it is convenient to use a special roof rack. Oversized cargo can be secured on this structure. Before choosing a product, you need to find out the dimensions of the elements that can be placed on the trunk. Long materials such as boards, sticks, pipes, if their length is up to 4.5 meters, may not be marked with red flags. If the cargo exceeds the dimensions of the vehicle, i.e. protrudes beyond the front and rear bumpers, it must be marked with special red flags that inform other road users about the transportation of oversized cargo.

What types of luggage racks are there?

On the roof of the VAZ 2107 you can install a roof rack of both the old type and the modern type. The standard “Zhigulevsky” trunk has dimensions of 1300*1050*215 mm, and its load capacity is up to 50 kg. This structure is fastened to the roof gutters using bolts. In general, roof racks can be divided into 3 groups:

The first option is universal. The product consists of transversely and longitudinally directed metal beams with a square or round profile.

The closed trunk is a trunk (box). The main advantage of this design is the protection of the transported cargo from bad weather.

The product, made in the form of racks, is used for transporting bicycles and other equipment. This design is used less frequently, but the load can be fixed on it easily and reliably.

Which manufacturer to choose

There are many manufacturers of roof racks for the VAZ 2107 on the Russian market. The most popular companies include: Mamont (Russia), Golitsyno (Russia), BelAZ (Belarus), Inter (Russia). The price range of products ranges from 640 rubles. up to 3200 rub.

How to install

Structurally, the roof of the “seven” has storm drains to which the trunk racks are attached. The installation of the structure for transporting luggage on the roof of the VAZ 2107 should be carried out at the same distance from the front and rear windows. Thus, the load on the upper part of the body and the pillars is distributed evenly. The rack fastenings are placed so that they do not create an obstacle to the doors when they open and close. On the Lada seventh model of recent years of production, there are special marks in the interior that indicate where the A-pillars are located. This makes it easier to install the product on the roof and position it.

Before tightening the racks, you need to make sure that they are parallel to each other without distortion. If an installation error occurs, the roof surface may be damaged. After installing the racks, tighten the fasteners tightly so that the rubber elements are pressed well against the roof gutters. Having secured the luggage structure to the body, the product is considered ready for use. The main thing is to ensure that the load is securely secured, which will prevent its loss during sudden braking or maneuvers.

Why do you need a roof rack?

The Seven belongs to the class of small passenger cars, which are designed to transport passengers, as well as small-sized cargo in the luggage compartment. However, very often there is a need to transport various cargoes, the dimensions of which exceed the dimensions of the car trunk. In this case, the top roof rack of the VAZ 2107 comes to the rescue, expanding the ease of use of the car.

A roof rack is installed on the roof of the vehicle in order to be able to transport various cargo. This can be things, tools, equipment, as well as other oversized cargo: building materials, bicycles, boats, etc.

The main condition that applies to objects transported on the roof of a car is that they must be securely fixed. Carrying cargo on the roof without a roof rack is strictly prohibited, as this is due to the lack of reliable securing of the cargo, and therefore safety. In addition, items transported on the roof will negatively affect the paintwork of the body.

Types of roof racks for VAZ 2107

It must be said right away that a standard factory-made trunk can be placed on the roof of the seven, which has dimensions of 1300x1050x215 mm, and its load capacity does not exceed 50 kg. These sizes are standard, and such products are suitable for most VAZ car models. The car is not equipped with such devices from the factory, but they can be purchased separately. Moreover, they are offered in several versions.

The Zhiguli roof rack is not the only option that is suitable for the VAZ 2107. Based on the type of design, the devices under consideration can be divided into three main groups:

Open type products are also called universal, as they are suitable for almost any task. Structurally, the device is a square or rectangular base, consisting of transverse and longitudinal jumpers (metal frame). Round tubes or a square profile are used as these jumpers. The dimensions of such a VAZ 2107 roof rack may differ from the standard ones, and they are selected depending on the parameters of the cargo being transported. The Zhigulevsk product is a classic representative of open-type luggage racks.

Closed-type devices look like a box made of plastic. This product has some advantages compared to the previous version - it is reliable protection of the transported cargo from bad weather and improved aerodynamics (less wind resistance), and therefore fuel economy. Typically, such luggage racks are used to transport things. It consists of a base and a lid, and has a fairly large capacity. Such devices are installed on the roof of the car when the whole family makes long trips.

The devices, which consist of two roof rails with crossbars, are used for transporting large building materials, as well as bicycles, etc. This option is also called a simplified version of open-type products, which has one significant advantage - it does not spoil the appearance of the car. Installing a roof rack allows you to do a little tuning of the car.

Installation of all of the above devices is carried out using special brackets that engage with the car's gutters. When choosing the devices in question, you need to know that they are adjustable, which allows you to install them on the roof of any classic VAZ, including the VAZ 2107.

How to install a roof rack on a VAZ 2107

Installation of the roof rack on the VAZ 2107 is carried out on special sides, which are called storm drains. These storm drains are places provided by the factory to protect door openings from the flow of precipitation from the roof. Installation of trunk mounts must be carried out at an equal distance from the front and rear windows of the car. This allows the load to be distributed evenly on the upper part of the body.

The fastenings are placed in such a way that there are no obstacles to opening and closing the doors. On the sevens on the interior side there are auxiliary marks indicating the location of the pillars. It is in the locations of these racks that the trunk must be installed. Installation of the selected roof rack on the roof of a VAZ 2107 car is carried out in the following sequence:

The VAZ 2107 roof rack must not only be installed correctly, but also properly operated. The maximum load should not be more than 60 kg. Moreover, it is important to take into account not only the weight of the cargo being transported, but also its dimensions. Transporting long items in the form of boards from 2-3 meters leads to the creation of additional load. It is formed due to the air flow, which acts on the front of the boards, trying to push them off the trunk. At the same time, fastenings on drains experience the heaviest load. In addition, transported long items must be marked with a red flag on the back.

Interior dimensions of the VAZ 2107

Overall dimensions of VAZ 2107 cars. Detailed data on the length, height and width of Lada (VAZ) 2107 cars, depending on the modification and year of manufacture. Standard ground clearance (clearance) of Lada (VAZ) 2107 cars.

Select the model and modification below:

Car modifications

The VAZ-2112 model during its production period underwent many changes and various modifications, not all of which were popular with consumers:

• 21120 – engine with the same number as the modification, with 16 valves according to the standard GLI luxury version of one and a half liters;
• 21121 – engine 21114, 1.6 liters with 8 valves;
• 21122 – engine 2111, volume one and a half liters, with 8 valves, budget version with 13 discs, without power windows, with non-ventilated brakes 2108;
• 21124 - with an engine of the same marking as the modification, but with 16 1.6 liter valves. It was produced until 2008. Despite the problem with valve bending, which was solved almost after the car was taken out of production. To achieve engine displacement from 1.5 to 1.6, the cylinder block changed significantly, becoming 2.3 mm higher, which accordingly affected the dimensions of the crankshaft parts;
• 21128 – 16 valves, engine with the maximum volume for this model (1.8 l). Luxury version from Super-auto JSC.

One of the versions of the VAZ-21123 was produced right up to 2009, but it was already a three-door and was produced in small series. The three-door hatchback had a 16-valve 1.6-liter engine in a luxury version. It was for this model that the term “coupe” was first used as a marketing ploy. But, besides this, this development had a body that was much stiffer and allowed the car to become more responsive on the road.

If you often transport medium-sized cargo, which includes products from your dacha, the VAZ-2112 car model will be the best option for you. The benefits of a large luggage compartment are obvious, and the ergonomic interior with folding rear seats doubles the cargo capacity.

home ⇒ equipment ⇒ luggage racks ⇒ vaz ⇒ vaz luggage racks The width of VAZ 2112 luggage racks for all modifications is . Years of production 1995 – 2008:

• Height: 680 mm;
• Diagonal: 1375 mm;
• Diagonal: 1375 mm.

Distinctive features of the “Seven” body

The body of the “seven” has a lot of advantages over the frame structure of cars. First of all, this has to do with reduced weight by 40-45 percent and lower production costs. The assembly itself also does not involve any particular difficulties: a cold-rolled steel sheet is used, usually 08KP, with the ability to draw and good weldability, as well as paintability.

The parts that are most susceptible to corrosion (underbody and its elements) are made from a special sheet of steel. Thus, in the VAZ 2107 of the last years of production, the number of galvanized parts exceeds in weight more than half of the entire body.

The most expensive part of any car is the body. Its production alone requires about half a ton of sheet metal (not cheap) and many other expensive materials.

As a result, the body has special requirements that it must meet:

• Have visibility in accordance with modern standards;
• Have a shape that is optimal in terms of aerodynamics and functionality;
• Seats must be securely fastened;
• Changes to the front and rear parts of the body should be within normal limits in case of unexpected accidents;
• The interior, engine and luggage compartments must have sufficient volume for a sedan;
• Compliance with all standards of painting, manufacturing, etc.;
• And finally, good maintainability.

Machine weight characteristics

For its time, the VAZ 2107 was an excellent car that was successfully sold, including outside our country. The machine's technical characteristics were not inferior to its analogues at a lower price; the design scheme used is highly reliable. The weight of the equipped vehicle is just over a ton, which allows it to demonstrate good power capacity.

The maximum permissible load is 400 kg, in other words the car can carry five adult passengers. If the quantity is smaller, luggage can be transported in a special compartment. A rational distribution of masses between the axles ensures good stability and controllability of the vehicle.

The small dimensions of the VAZ 2107 model, optimal weight for its size and a powerful engine provide the car with good dynamics and maneuverability. The successful design and low price predetermined the car's commercial success and, despite its advanced age, it still does not lose popularity.

VAZ 2107 is a rear-wheel drive car of group II of the small class of the AvtoVAZ company, produced from 1982 to 2012.

Body dimensions of VAZ 2107:

• VAZ 2107 2107 1.5 MT (72 hp): 4145x1620x1440 (mm).
• VAZ 2107 2107-20 1.5 MT (68 hp): 4145x1620x1440 (mm).

Dimensions are given in length/width/height format.

Note:

• VAZ 2107 body type: sedan (4 doors, 5 seats).
• Standard clearance size: 170 (mm).

Important: the wheelbase size of VAZ 2107 modifications is 2424 (mm)

The size of the luggage compartment in the VAZ-2111

Trunk volume on a VAZ 2114 in liters
Although many foreign cars are in fashion today, the VAZ-2111 still remains a workhorse, the advantages of which are that the car can be used in any conditions, as well as repaired with your own hands. Expensive brands of cars require ordering auto parts; often they need to wait for 2-3 months, which is extremely inconvenient - the car is idle, and the driver becomes a pedestrian.

This definitely won’t happen with the VAZ-2111 - the mechanics and manual controls allow even a beginner to quickly and easily deal with problems, because parts for the car can be bought at the first service station or a specialized auto parts store.

The luggage compartment of the VAZ-2111 has the following characteristics:

• if loaded to the ceiling, perhaps 575 liters;
• folded seat allows you to increase 1215 liters.

Now about the size of the trunk. Provision is made for the transportation of narrow cargo with a long format. The backrest of the rear seat, located in the middle, can be reclined completely, while those located on the sides recline, taking into account the smaller amplitude.

What quantities may also be useful:

1. Loading height of luggage compartment.
2. The length, if we focus on the cargo loading height level, is 965 mm.

The dimensions of the luggage compartment with the rear seat folded down on the VAZ-2111 are as follows:

• the entire length of the VAZ-2111 trunk is no more than 1630 mm;
• the pitch to the rear seats is approximately 1030 mm;
• as for the width of the compartment between the wheel arches, it reaches 930 mm;
• height is also 930 mm;
• If you measure the height of the rear door opening, it is 890 mm.

If cargo is being transported, the load capacity of the VAZ-2111 is 500 mm, and when loaded it is 1030 mm.