Improved connection of trunk lighting for Lada Granta, Kalina and Priora
When the trunk is opened, the light comes on only when the lights are on - this is a drawback of the standard connection of the trunk light of many AvtoVAZ cars (including Lada Granta, Priora, Kalina).
We offer you a method that will make the lighting in the luggage compartment independent. You will need : several meters of wire, a multimeter or test lamp, electrical tape.
In order for the backlight to turn on when the trunk lid is opened, regardless of the dimensions, it is necessary to lay a wire from the ceiling (navigator) lamp on the ceiling (where there is a constant + 12V) to the trunk light. It is not at all necessary to remove the roof trim, just bend it a little from the edge or move it out a little from the door seal.
one end of the wiring to the central wire of the interior lamp connector (for Lada Priora) or to the outer wire for Lada Kalina/Granta (white or white-red). The color of the wires may vary depending on the car model or its configuration, so first check it with a multimeter or test lamp. We hide the wire under the door seal and run it down to the lamp in the trunk.
The other end of the wiring goes to the light in the trunk. Two wires come to it, one of them is ground, and the other is + 12V from the dimensions (usually yellow-red or yellow). It is also recommended to check with the device first. Disconnect the second wire and isolate it. In its place we connect the wire from the navigation lamp. Ready!
Lada Priora front lamp diagram:
- far left (red) – “mass”
- central (white) – +12V
- far right (black) – ground (door switches)
Diagram of the front lamp of Lada Granta (pre-style) and Lada Kalina:
- far left (black) – “mass”
- central (green) – “ground” (door switches)
- far right (red) – +12V
Diagram of the front lamp with ERA-GLONASS for Lada Granta FL:
- 11 and 14 – +12V appears after turning on the main relay (turning on the ignition, opening the doors). The power goes out 2-5 minutes after removing the ignition key.
- 15 – “mass”.
- 17 – “ground” (door limit switches), which appears for a while when the doors are opened.
By the way, in the “Lux” configurations, the middle wire of the ceiling lamp has an auto-shut-off function after 10 minutes of inactivity, which is very convenient.
Let us remind you that constant +12V can be taken from other sources, for example:
- From the ignition switch (pin 50)
- ISO connector of the radio (A4 contact)
- Cigarette lighter (middle wire white-red or red-blue)
Have you made the trunk lighting independent of the dimensions? Perhaps you have thought about installing additional lighting in your doors?
Source: xn--80aal0a.xn--80asehdb
Installation of additional lighting in the trunk and trunk shelf of the Lada Priora
The content of the article:
Installation of additional trunk lighting of Lada Priora
Immediately after buying the car, I was depressed by the flashlight in the trunk. There was absolutely no sense in him. Replaced it with 6 powerful LEDs. There was much more light, but it was still not enough, because the entire luggage compartment is lined with black light-absorbing material and there is nothing there to reflect light. Some time ago I got hold of an LED strip at work. I carried it for a very long time and could not find a use for it. And so it came in handy for me. I bought male and female connectors like this
I cut a piece of tape of the required length and soldered one of the connectors to it
Then I decided that I would power this tape through a separate fuse, because I didn’t even know approximately how much it consumes. The second connector was also soldered.
Next, I tested the tape and it turned out that it consumes only 250 mA.
Without further ado, I attached the tape with four plastic clamps to the top crossbar of the Tekhnomaster body reinforcement. The tape went from the bottom of the crossbar.
Several times I had to remove this crossbar to transport large items. It is easy to remove - it takes about 10 minutes. Therefore, if in the future I need to remove it again, I will simply disconnect the connectors of the tape and remove the crossbar along with the tape.
I pulled out the connectors for clarity. In fact, they are hiding under the skin.
Well, the result of the work done. I took this photo specially without flash. Oh, yes, I powered the tape from the trunk light.
There is so much light that I can even give half of it to someone
Luggage shelf lighting for Lada Priora
Someone the other day was interested in how the trunk rack illumination would be implemented. Here is the report. It's simple. I bought a semi-luxury Priora lamp, installed bright LEDs in it instead of the standard incandescent lamp, and embedded this lamp into the plastic trim of the trunk door. I laid the wires inside the rear door through the standard rubber corrugation. That is, I simply added a couple of wires to those already there. I used fiberglass cable traction for these purposes.
The plastic is very soft and can be cut easily with a knife. By the way, it scratches just as well
