Scher-Khan Magicar 10: Instructions and manual in Russian

Manual …

Page 2

Image
Text

Manual

Vehicle alarm system STSTS

SCHER-KHAN MAGICAR 10 (hereinafter referred to as the system) complies with the mandatory

requirements in the GOST R certification system for devices

protection for a car: GOST R 41.97-99 (Uniform regulations regarding official

approval of vehicle alarm systems

(STSTS) and motor vehicles in relation to their systems

alarm system (STS)) GOST R 50009-2000 (Electromagnetic compatibility of technical equipment.

Technical means of security alarm. Requirements and Methods

tests)

Thank you for purchasing a two-way car security system.

SCHER-KHAN MAGICAR 10 systems

Our company's continuous research and development embodies

the most advanced ideas and serve to satisfy all needs

users of our systems. System SCHER-KHAN MAGICAR 10

is a complex electronic

vehicle equipment. From its functioning and correct

installation depends on the safety of your life, health and road

situation, the quality of work of nearby radio-electronic

equipment and communications. Trust the installation of the system only

specialized service stations. During operation

Periodically check that the system is functioning correctly.

Attention!

When purchasing, check that the warranty card is filled out correctly. The manufacturer and supplier of the system are not responsible

for any disregard of the installation manuals and

operation, as well as for errors made during installation. The manufacturer reserves the right to make changes to

system design in order to improve its consumer properties.

If problems arise with the operation of the system,

please contact the service center immediately

for diagnosis or consultation.

The engine started, but it doesn’t show on the key fob

If the car was started not from an additional key fob, but from the main one, and incorrect information is displayed on it, then you should look for an error made when installing the alarm system.

Check that each connector on the main module is connected correctly. If there is no malfunction, contact a specialist.

Author of the material: Dumchenkov Mikhail

Have questions about car repairs? Ask them in the consultation section, to do this, click on the link below.

auto mechanic

New cars 2020
New cars 2021
Test drives
Jeeps
Crossovers

Repair and maintenance Engine
Chassis
Electrical equipment

Alarms
Cigarette lighters
Car Reviews
Photo and video galleries
News
Tires
Celebrity cars

2020 Daciaclubmd.ru. If you do not agree with any provision of this Disclaimer, do not use this Site. Please read Disclaimer and Privacy Policy before use.

Source

is a car alarm with the ability to control...

Page 3

Image
Text

SCHER-KHAN MAGICAR 10

PURPOSE SCHER-KHAN MAGICAR 10

System SCHER-KHAN MAGICAR 10

is an automobile

alarm with the ability to control via radio channel via

key fob communicator with liquid crystal display. System

exchanges information between the key fob communicator and

processor unit at a distance of up to 2,000 m. The system is designed

for operation on vehicles with an on-board voltage of 12 V and

provides the ability to connect to the standard data bus

Vehicle CAN. Protection of the processor unit, shock sensor, sensor

call, the antenna unit is made according to the IP-40 standard and provides

installation inside the car. The siren is made according to the IP-65 standard

and can be installed in the engine compartment, away from the exhaust

collector and high-voltage systems. System SCHER-KHAN MAGICAR 10

equipped with built-in

car digital CAN bus adapter. The device is intended

for quick and correct installation of alarm systems on cars,

equipped with body CAN BUS buses. The adapter reads

vehicle CAN bus signals and generates the data necessary for

connection of the security system. The digital bus module allows for comprehensive

information about the main components of the machine. CAN adapter simplifies

complex procedure for installing a security system on a car: no

the need to search for signals from various electronic devices using

throughout the car, the number of connecting wires is reduced to a minimum,

you can install an alarm system in the most complex and inaccessible

areas of the car, which significantly increases anti-theft

properties of the security system due to the possibility of installing it to the maximum

secretly.

Manual …

Page 4

Image
Text

Manual

Content

PURPOSE OF SCHER-KHAN MAGICAR 10

…………………………… 3

DELIVERY SET …………………………………………………………………………………….. 6

LIST OF FUNCTIONS……………………………………………………………………………………….. 7

Functions of the key fob communicator……………………………………………………….. 7

Functions of the processor unit………………………………………………………………. 7

TECHNICAL PARAMETERS……………………………………………………………………… 9

DESCRIPTION OF KEY FOBS

PREPARING THE KEY FOB COMMUNICATOR FOR OPERATION………………………. eleven

SYMBOLS ON THE DISPLAY OF THE KEY FOB COMMUNICATOR………………………. eleven

PURPOSE OF KEY FOB COMMUNICATOR BUTTONS

AND AN ADDITIONAL KEY FOB……………………………………………………….. 13

CORRESPONDENCE OF MAIN BUTTONS

AND ADDITIONAL KEY FOBS……………………………………………………….. 14

KEY FOB COMMUNICATOR SETTINGS …………………………………………. 15

TURNING ON THE DISPLAY BACKLIGHT…………………………………………………… 17

PARKING TIMER FUNCTION ………………………………………………… 17

KEYBOARD LOCK……………………………………………………………… 17

ENERGY SAVING MODE “BATTERy SAvE MODE” …………………………. 18

DRIVING THE SECOND VEHICLE………………………………………………………………. 18

INDICATION OF FEEDBACK SIGNAL LEVEL …………………………… 19

SYSTEM OPERATION

ARMING ………………………………………………………………………………… 19

ARMING WITH THE ENGINE RUNNING……………….. 21

ARMING IN “PIt-StoP” MODE ……………………………….. 22

AUTOMATIC ARMING ……………………….. 25

ALARM MODE………………………………………………………………………………….. 26

REMINDER MODE FOR MISSED ALARMS……………………. 27

DISARMING ……………………………………………………………………………….. 28

AUTOMATIC RETURN TO SECURITY MODE………………………………. thirty

HANDS-FREE FUNCTION ……………………………………………………………. thirty

OPENING THE TRUNK …………………………………………………………………………………………. 32

CHECKING THE SYSTEM STATUS ………………………………………………………. 33

CALLING THE CAR OWNER ……………………………………………………… 35

PANIC MODE OR JACKStoP™ …………………………………………………….. 36

User manual

No more than three key fobs can be stored in the memory of the microprocessor unit; their programming is mandatory.

Pager Programming Guide:

With the security function disabled, turn the key in the lock to On and click the call sensor button and hold it for two seconds. The vehicle's optics should light up.
Within five seconds, you need to press the button again, but do not hold it down. The machine's lights will blink again, and the LED indicator will blink quickly.
Within four seconds after this event, you must press the call sensor button the number of times that corresponds to the first digit of the password. The interval between clicks should be no more than one and a half seconds. Four seconds after the last press, the machine's lights will blink once, which indicates successful acceptance of the first digit of the password. The LED indicator will flash quickly.
The previous paragraph is repeated for the remaining digits of the password.
Five seconds after entering the last digit of the code, the LED indicator will begin to light continuously.
Then, within five seconds, click on the fourth key on the remote control. The vehicle's lights will blink once. The remaining pagers are linked in the same way.

Setting up autorun

The motor is started on command by pressing the second key on the remote control for two seconds. The protective mode will be activated, the door locks will close and the engine will start. The pager screen will display the time remaining until the engine stops.

By time

Setting the timer to activate the function:

Briefly click on keys 2 and 4 of the pager. This will activate the option programming menu.
To enter the timed engine start mode, hold down the fourth key until the siren emits thirteen beeps.
Set the engine start time. To start, the fourth button is clicked every two hours, and the third button is clicked to start every four hours.
After setting the time, press buttons 2 and 4 again.

By temperature

Starting an internal combustion engine based on temperature:

In accordance with the service manual, connect mode 1-13.
Activate function 1-21, it is used to control the temperature parameter.
Use key number 4 to activate the temperature function. The siren of the security complex will emit 21 signals.
Specify the temperature that will be used for automatic start. To start when the temperature drops to -15 degrees, click on the second button, at -25 degrees - on the third, etc.
The next step is to press buttons 2 and 4.

Disabling the feature

To disable the option, deactivate the ignition and enter the programming menu by pressing keys 1 and 4 and holding them for two seconds. Briefly click on the third button. The car's lights will blink and the siren will sound three times. The option will be disabled.

Autostart does not work: troubleshooting

If the autostart stops working and the engine does not start, you need to figure out the reasons why the function may not work:

The motor has already started. In this case, the car's lights will blink once when you try to configure the option.
The car's ignition is activated. The car's lights will blink twice.
One or more doors are open. The warning light will blink three times.
The trunk door or hood is open. The vehicle's lights will blink four times.
The consumer has not configured the start reservation for the manual transmission. The car's lights will blink five times.
The handbrake lever is disengaged. The warning light will blink six times.
The brake pedal is depressed. Seven light signals will indicate this.
The engine does not start for other reasons - the lights will blink eight times. These reasons may be due to malfunctions in the operation of the unit, starter device or other elements of the ignition system. Problems in starting the internal combustion engine may be associated with a breakdown of the fuel pump or failure of the relay that protects its electrical circuit.

TURNING OFF SIREN SIGNALS……………………………..

Page 5

Image
Text

SCHER-KHAN MAGICAR 10

TURNING OFF SIREN SIGNALS…………………………………………………….. 37

SERVICE MODE vAlEt ………………………………………………………………………………… 38

TURNING THE SHOCK SENSOR ON AND OFF

AND AN ADDITIONAL SENSOR………………………………………………………. 40

POWER-ON CONTROL OF CENTRAL LOCKING

AND TURNING OFF THE IGNITION………………………………………………………………. 42

“TURBO” MODE ………………………………………………………………………………….. 42

CONTROL OF ADDITIONAL CHANNEL 1 …………………………………. 46

CONTROL OF ADDITIONAL CHANNEL 2 …………………………………. 48

DISARMING THE SYSTEM WITHOUT A KEY FOB

AND APPLICATION OF PERSONAL CODE …………………………………………… 50

DISARMING THE SYSTEM WITHOUT A KEY FOB

USING PIN 1 ………………………………………………………………………………….. 51

ACCESS TO THE CAR WITHOUT KEY FOB

USING PIN 2 ………………………………………………………………………………….. 53

WARNING ABOUT OUT OFF SIZES………………………. 55

BLOCKING THE STARTER OR IGNITION ………………………………………… 55

DOOR OPEN WARNING ………………………………………….. 56

ADDITIONAL LIGHTING WHEN STAGING

AND DISARMING ……………………………………………………………………………………… 56

SEARCHING FOR A CAR ………………………………………………………………………………….. 56

PROTECTION OF RADIO CHANNEL AGAINST CODE INTERCEPTION………………………………….. 56

ADJUSTING THE SENSITIVITY OF THE SHOCK SENSOR ……………………… 57

ADJUSTING THE SENSITIVITY OF THE OWNER CALL SENSOR ... 57

PROGRAMMING THE TACHOMETRIC SIGNAL ……………………. 57

KEY FOB PROGRAMMING ………………………………………………………. 58

PROGRAMMABLE FUNCTIONS………………………………………………………………. 59

Manual …

Page 8

Image
Text

Manual

• Personal code for disarming the system if the key fob is lost (PIN 1)

• Personal code for access to the car interior if the key is lost

(PIN 2)

• Two-step disabling of security (possible using

personal code)

• Vehicle security mode with the engine running

• Security mode without siren warning signals, without

siren alarms or hidden security (programmable

function)

• Hands-free function for automatic arming/unarming

from security when the owner moves away/approaches the car (two

mode)

• Power output for controlling the central locking of the vehicle

• Driver's door priority unlocking (programmable function)

• Power output for trunk release

• Power output for alarm control (two circuits)

• Two independent blocking relay control outputs (NC and NO)

• Two universal programmable control channels

additional devices with the ability to change

work algorithms

• Independent additional sensor input

• Accounting for interior light delay (programmable function)

• Possibility of connecting negative and positive sensors

doors

• Selecting the duration and number of door lock control pulses

• Locking and unlocking of doors when turning on and off

ignition

• Turbo timer mode with variable turbine cooling time

engine

• Monitoring the intensity of engine operation using the tachometer

signal

• Automatic arming (programmable function)

• Automatic return to security mode if the door is not opened

(programmable function)

• Door open alarm warning

(programmable function)

• Warning about side lights not turned off when parking

arm (programmable function)

• Panic or JackStop™ mode (programmable feature)

How to setup

It is not difficult to start the automatic alarm on Sherhan alarms. To do this, you should study the detailed car alarm manual and successively press the settings buttons.

To activate the mode and safely use autorun, you need to activate the protective functions and perform a number of preparatory steps:

First of all, with the engine running, the doors closed and the brake pedal lowered, you need to press the 3rd button of the key fob.
If the key is inserted into the ignition, it must be removed. In modern cars this element is missing - Start/Stop buttons are used instead.
After completing the above steps, you need to get out of the car and press the security buttons.

To configure autorun from the key fob, you must do the following:

Long press button 3 until a smoke indication appears on the pager monitor, indicating a successful start-up.
Wait for the countdown. To restart it and cancel the timer, just press the same button again.
To turn off the mode, you need to press the button from the first stage until the sound alert sounds.

Setting by interior temperature

To configure autostart based on the temperature inside the car, you must first activate the activation mode by time interval (1-13). After this, you need to go to the programming menu by long pressing buttons 1 and 2 on the key fob. Next you should perform the following steps:

Deactivate the timer (if it was enabled), following the previous instructions.
Press the 4th button 21 times until the final sound indicator sounds.
Select the optimal temperature range at which the option will start.
Restart the timer.

Setting by on-board voltage

The engine is started automatically on the Sherkhan based on the on-board voltage readings. It occurs when the battery level drops to 11.5 V. For the function to work properly, we configure autostart on the Sherkhan alarm system according to the following instructions:

We make 20 presses on button 4.
We are waiting for the siren to emit a similar number of sound notifications.
Activate the option with button 2.

How to set the warm-up interval

To select the desired time interval after which the engine will automatically start, set function 1-12 to position 2.

How to program the warm-up duration

The detailed guidance for performing this action is as follows:

First, the user needs to activate the programming mode by setting function 1-12. To do this, long press buttons 1 and 12 until the corresponding sound alert sounds.
Next, you should wait for a 12-fold response from the siren and select the optimal warm-up range. Using button 1 you can set a 5-minute interval, button 2 - 15 minutes, button 3 - 25 minutes, and button 4 - 45 minutes.