Wheels for Daewoo Nexia: size and parameters of alloy wheels for Daewoo Nexia

Designation and marking of wheels

The main difference between wheel bolt pattern is the marking of Daewoo Nexia wheels.
It is the same for both cast and stamped models. In most cases, it is marked as follows: 5.5Jx13 4/100 ET 49 for steel wheels, 5.5x14 4/100 ET 49, steel for Euro III, IV; 5.5Jx14 GLE. It is quite easy to understand such inscriptions. Factory wheels for Nexia, produced by the Uzbekistan Automobile Plant

The width of the disk is indicated by the very first character - in this case it is the number 5.5. Diameter – numbers 13 and 14. Both parameters, respectively, are measured in inches. The amount of offset, or overhang, of the product is designated “ET 49”. And here's a chat about

This is what you should pay special attention to: the number of bolts is indicated by the first digit, the diameter of the fasteners – by the second digit

The “ET30” value, which has already been mentioned, denotes the offset indicator, in this case equal to 30. Simply put, thirty millimeters is the distance between the center of the disk width and its mating plane. The mating plane is understood as that part of the product that is pressed directly against the hub.

The disk markings look like this

Installing a brake disc on the front of a Daewoo Nexia: step-by-step instructions

The procedure for installing brake discs on a Nexia will not be particularly difficult, even if you lack practical skills in car repair - the procedure algorithm is intuitive. To replace components, you will need no more than an hour of time on both wheels, as well as a set of wrenches, an automotive Torx, a long slotted screwdriver and a hammer. The replacement procedure is performed as follows:

• To begin with, we park the car on a level area and put the handbrake and first gear in;
• Next, jack up the wheel and remove the brake mechanism. We dismantle the pads by first unscrewing and bending the steering rack guides to the sides. When removing parts, it is important not to break the friction springs that stabilize the operation of the pads;
• Then we remove the brake caliper, after which we take out the brake disc. If difficulties arise while dismantling the caliper, it is necessary to pump out some brake fluid from the expansion tank under the hood of the car;
• After complete disassembly of the brake mechanism, we carry out maintenance of the entire system - if necessary, we change the dust-proof corrugations on the welding pads and the brake caliper, and also lubricate the guide axes and clean the surface of the new disc. In order for the disc to work effectively throughout its entire service life, it is necessary to wipe the surface with a cotton pad soaked in an alcohol solution;
• Now we assemble the brake mechanism. We mount a new disc, after which we install new pads, after squeezing the brake cylinder to the side until it stops with the tip of a slotted screwdriver;
• Next, screw the guides and put the wheel in place. When the replacement is complete, a similar procedure is performed with the second wheel of the car.

Note! It is recommended to change brake discs around the car or at least in pairs - that is, on both wheels of the axle. Otherwise, the wheels may grip unevenly when braking, which will lead to imbalance of the car on the road and increase the likelihood of an accident.

Daewoo Nexia GM T Restailing 2013 1.5i

Tire and wheel sizes for the 2014 Chevrolet Cruze
Generation: GM T Restailing Engine: I4, Gasoline Power: 84 hp
(62 kW) Wheel bolt pattern parameters

What wheel sizes does the manufacturer recommend to install?

The Daewoo Nexia GM T Restailing 2013 1.5i is equipped with 5.5Jx14 ET49 rims assembled with 185/60 R14 82T tires as standard. Where:

• 5.5J - rim width in inches;
• 14″ — tire diameter in inches;
• ET49 - disc offset in millimeters.

The vehicle tire marking 185/60 R14 is deciphered as follows:

• 185 — profile width (cross section of the tire) in millimeters;
• 60 - profile height as a percentage of its width;
• R - radial cord winding;
• 14 is the tire diameter in inches.

In addition, information about its load capacity and speed parameters can be printed on the rubber - load index and speed index. The load index is a two- or three-digit number; the speed index is indicated in Latin letters, for example 82T:

• 82 - maximum permissible tire load 475 kg;
• T — maximum permissible vehicle speed is 190 km/h.

Using the recommended tire sizes will help you avoid problems with handling, safety and other difficulties. What non-standard sizes can be supplied? Refer to the table; it indicates possible acceptable alternative sizes for tuning. Although there are other options that we have not described in the table. For example, wider discs of the same diameter. Or install wheels of the same width, but with a larger diameter, which is quite popular among car owners. The choice of discs is huge; you can find copies with the same parameters, but with an overhang 1-2 millimeters more or less. It is not possible to list all the options.

At the same time, the bolt pattern for all types of wheels is the same - 4x100. Thus, all disks are mounted with four bolts and the distance between them is exactly one hundred millimeters. The car's hub diameter is 56.6 mm.

Characteristics and parameters of wheel bolt pattern on Daewoo Nexia

The drilling parameter for absolutely all cars produced all over the world is designated PCD, which stands for Pitch Circle Diameter. The bolt pattern of Nexia wheels is 4x100. This applies to any car produced, regardless of where the plant is located and what year the model was released. In this case:

• The number 4 indicates how many bolts are used to secure the rim. In other brands and models, the value may be different, from three to six;
• 100 shows the diameter of the circle on which the mounting holes are located.

All data is extremely important when choosing a new set of disks.

Knowing the meaning of the bolt pattern, you can not rely on the knowledge of the sales consultant, but choose the wheels you like yourself. A fluctuation in diameter size of even a millimeter is unacceptable.

You might be interested in Wheels for Renault Kaptur - sizes and parameters

For the most accurate selection of wheels for the Daewoo Nexia, you need to know such parameters as the bolt pattern and the dimensions of the mounting holes. Having such information, there will be no problems with selection and purchase.

Before purchasing, it is also advisable to consult with the seller about the chosen model. It is possible that some wheels do not perform well during operation.

Important!

When choosing rims, you need to take into account the factor whether it is possible to buy tires of similar sizes.

The larger the wheel size, the better the quality of handling and behavior on the road. But you should also take into account the increased wear rate of suspension parts and the decreased level of driving comfort. In addition, the larger the size of the wheels themselves, the lower the profile of the tires themselves must be chosen. This will also not have the best effect on the wear of the wheels themselves, since the level of load on them will increase.

For the winter season, 14-inch wheels are most suitable for the Daewoo Nexia. They will give the car optimal performance in poor operating conditions and on rough roads.

In summer, it is recommended to install wheels with a diameter of 15 inches for maximum traction and best handling.

Tire parameters for Daewoo Nexia:

• Diameter (measured in inches) - from 14 to 16;
• Width (millimeters) - from 185 to 215;
• Tire profile (%) - from 40 to 60;
• The minimum tire size is 185/60 R14;
• The maximum tire size is 215/40 R16.

Disc parameters for Daewoo Nexia:

• Drilling (often referred to as bolting) - 4×100;
• Diameter (measured in inches) - from 14 to 16;
• Width (inches) - from 5.5 to 7
• Wheel offset ET (millimeters) - from 45 to 49;
• Center hole diameter (DIA) is 56.6.

Daewoo Nexia GM T Restailing 2011 1.5i

Tire and wheel sizes for a 2004 Chevrolet Niva

Generation: GM T Restailing Engine: I4, Gasoline Power: 84 hp
(62 kW) Wheel bolt pattern parameters

What wheel sizes does the manufacturer recommend to install?

The Daewoo Nexia GM T Restailing 2011 1.5i is equipped with 5.5Jx14 ET49 rims assembled with 185/60 R14 82T tires as standard. Where:

• 5.5J - rim width in inches;
• 14″ — tire diameter in inches;
• ET49 - disc offset in millimeters.

The vehicle tire marking 185/60 R14 is deciphered as follows:

• 185 — profile width (cross section of the tire) in millimeters;
• 60 - profile height as a percentage of its width;
• R - radial cord winding;
• 14 is the tire diameter in inches.

In addition, information about its load capacity and speed parameters can be printed on the rubber - load index and speed index. The load index is a two- or three-digit number; the speed index is indicated in Latin letters, for example 82T:

• 82 - maximum permissible tire load 475 kg;
• T — maximum permissible vehicle speed is 190 km/h.

Using the recommended tire sizes will help you avoid problems with handling, safety and other difficulties. What non-standard sizes can be supplied? Refer to the table; it indicates possible acceptable alternative sizes for tuning. Although there are other options that we have not described in the table. For example, wider discs of the same diameter. Or install wheels of the same width, but with a larger diameter, which is quite popular among car owners. The choice of discs is huge; you can find copies with the same parameters, but with an overhang 1-2 millimeters more or less. It is not possible to list all the options.

At the same time, the bolt pattern for all types of wheels is the same - 4x100. Thus, all disks are mounted with four bolts and the distance between them is exactly one hundred millimeters. The car's hub diameter is 56.6 mm.

Wheel bolt pattern Daewoo Nexia 2011 1.6 (109 hp, gasoline)

1. Razboltovka.ru
2. Daewoo
3. Nexia
4. 1.6 (109 hp, gasoline)
5. 2011

Find disk parameters for Daewoo Nexia 2011, 1.6 (109 hp, petrol).

Table of parameters and wheel bolt patterns for the Daewoo Nexia 1.6 model (109 hp, gasoline) - 2011.

Disc drilling parameters are usually called bolt pattern:

• LZ (number of holes)
• PCD (hole center circle diameter)
• ET (disc offset)
• DIA (hole diameter)

Save just in case so as not to lose! Make model modificationAuto Year of manufacture Wheel width Wheel diameter Bolt pattern LZ*PCD Offset ET DiameterDIA Installation type

razboltovka.ru

Designation and marking of wheels

Tire and wheel sizes for VAZ 2112 2004

The main difference between wheel bolt pattern is the marking of Daewoo Nexia wheels. It is the same for both cast and stamped models. In most cases, it is marked as follows: 5.5Jx13 4/100 ET 49 for steel wheels, 5.5x14 4/100 ET 49, steel for Euro III, IV; 5.5Jx14 GLE. It is quite easy to understand such inscriptions.

Factory wheels for Nexia, produced by the Uzbekistan Automobile Plant

The width of the disk is indicated by the very first character - in this case it is the number 5.5. Diameter – numbers 13 and 14. Both parameters, respectively, are measured in inches. The amount of offset, or overhang, of the product is designated “ET 49”. And here's a chat about

This is what you should pay special attention to: the number of bolts is indicated by the first digit, the diameter of the fasteners – by the second digit

The “ET30” value, which has already been mentioned, denotes the offset indicator, in this case equal to 30. Simply put, thirty millimeters is the distance between the center of the disk width and its mating plane. The mating plane is understood as that part of the product that is pressed directly against the hub.

The disk markings look like this

Brake discs for Daewoo Nexia

The brake system is an important structural unit that is responsible for the safe operation of the vehicle. One of the most important components that require timely maintenance and repair is the brake disc, which is recommended to be changed every 60-70,000 km.

The Daewoo Nexia is equipped with double-sided brake discs from the factory with a total design height of 41 mm and a thickness of 18-20 mm. The outer diameter of the brake disc must correspond to 236.50 mm with 6 centering holes for mounting. If you purchase an atypical brake disc, the part must be identified by article number and compatibility determined.

Also, when choosing brake discs, it is recommended to look for models with a ventilated surface, which will create an additional cooling effect and prevent the brakes from overheating in the event of an emergency stop.

It is important to know! When purchasing components, it is advisable to check the part numbers with the VIN number of the vehicle for compatibility - if the kit is unsuitable for your car, it is advisable to refuse the purchase. The best option for Nexia would be to install a stock kit recommended by the manufacturer or install parts from well-known brand companies.

Designation and marking of wheels

The main difference between wheel bolt pattern is the marking of Daewoo Nexia wheels. It is the same for both cast and stamped models. In most cases, it is marked as follows: 5.5Jx13 4/100 ET 49 for steel wheels, 5.5x14 4/100 ET 49, steel for Euro III, IV; 5.5Jx14 GLE. It is quite easy to understand such inscriptions.

The width of the disk is indicated by the very first character - in this case it is the number 5.5. Diameter – numbers 13 and 14. Both parameters, respectively, are measured in inches. The amount of offset, or overhang, of the product is designated “ET 49”. And here's a chat about

This is what you should pay special attention to: the number of bolts is indicated by the first digit, the diameter of the fasteners – by the second digit

The “ET30” value, which has already been mentioned, denotes the offset indicator, in this case equal to 30. Simply put, thirty millimeters is the distance between the center of the disk width and its mating plane. The mating plane is understood as that part of the product that is pressed directly against the hub.

How to replace discs on the rear axle of a Nexia: step-by-step instructions for beginners

The installation of a new set of brake discs on the rear axle of the Daewoo Nexia is carried out in a similar way, but has a couple of features due to the difference in the wheelbase design. To replace the disks, you will also need up to an hour of free time and a set of wrenches and sockets, a jack, a slotted screwdriver or a small crowbar for beading the wheel and a wheel wrench. The replacement procedure is as follows:

• First you need to park the car on a level surface, then move the gearbox selector to the first or reverse gear position;
• Next in the cabin, under the rear seats, you need to find a small hatch that will provide access to the handbrake cable system. On each power element it is required to loosen the tension as much as possible;
• Now lift the rear of the vehicle and remove the wheel. Afterwards, we disassemble the brake mechanism, unscrew the housing and take out the brake pads, having previously disconnected the hook adjacent to the cable from the handbrake from the top. Now you will have access to the brake disc, which we also remove by unscrewing all the fixing fasteners;
• We wipe the new disc with alcohol and put it in place, after which we install a new set of brake pads. To complete the procedure, put the wheel in place and repeat similar operations on the other side of the car.

It is important to know! After installing new brake discs on a car, it is recommended to run-in the components - within 200 km after repair, it is not advisable to resort to emergency or prolonged braking.

Otherwise, an abrasive groove may form on the unlapped surface of the brake disc, significantly reducing the service life of the part. Properly carried out running-in will extend the life of both the brake mechanism and other vehicle systems, and will also ensure maximum safety for the driver and passengers in the cabin while driving.

Pay attention to the table and compare the results

To be confident in the data obtained from independent measurements, you should check the information with the tabulated values. If you have, for example, a Mercedes, and the parameters you obtained are 111 millimeters, use the tabular numbers (112 millimeters), since the German Mercedes does not produce wheels with a bolt pattern of 110 or 111 mm. The domestic auto industry also has its own values ​​regarding these parameters. For example, the bolt pattern of VAZ wheel rims is 4x98 millimeters. That is, if during independent measurements you come up with a value of 99 or 97, we focus primarily on the tabular data. But not all VAZs have such a bolt pattern. For example, on the Niva 2121 series this parameter is 5×139.7.

By the way, on most European foreign cars this value is the same (it is one hundred millimeters) regardless of body type, year of manufacture, generation and engine size.

VAZ, Chevrolet Cruze, Daewoo Nexia, Hyundai Accent... :: SYL.ru

Every car owner sooner or later thinks about changing the appearance of his vehicle. Of course, high-quality tuning of the car will be considerable pleasure for the driver, considering that it includes installing various body kits and changing the technical characteristics of the engine. But you can also partially transform the car, for example, by equipping it with new alloy wheels. However, when choosing, it is worth considering not only the offset, width and diameter, but also such a parameter as the disc bolt pattern. We'll talk about it today.

What it is? Characteristics of the bolt pattern

The bolt pattern of the wheel rims is the diameter of the holes intended for the bolts. Abroad, this characteristic is designated by the abbreviation PCD. Why is this parameter important for a car? If the bolt pattern of the wheel rims does not match the specific car model, they will be installed off-axis. Of course, this will not affect the appearance of the vehicle in any way, but the technical part will suffer to the fullest. When the car moves, discs mounted off-axis destroy elements of the steering mechanism and suspension. Neglecting this parameter can lead to the wheel turning loose while driving, which will certainly lead to a traffic accident.

Wheel marking and encryption

Speaking about the features of the bolt pattern, it is impossible not to note the markings of the disks. Most often, it is the same for both cast and simple stamped products. This factor is designated approximately this way: 6Jx17h3 ET30 PCD: 5/112 d 66.6. What does it mean? Let's look at everything in order.

Factor 1

The first character "6" indicates the width of the disk. The next number, seventeen, indicates its diameter. Both values ​​are measured in inches. “ET30” is an indicator of disc offset or offset. “5/112” is the bolt pattern itself. Particular attention should be paid to the last point. What does the bolt pattern 5/112 tell us? The first number indicates the number of mounting bolts required. The symbol “112” indicates the diameter of these bolts.

Factor 2

Another nuance is the value “ET30”. In our case, this indicates an overhang indicator that is equal to 30. That is, the gap between the mating plane of the disk and the center of its width is thirty millimeters. The mating plane is the part of the product area where the disk is pressed against the hub itself.

Positive, negative and zero offset of car rims

In what case will the disk have such performance indicators? The wheel receives zero offset only if the center of the width and the mating plane completely coincide with each other. Positive offset is achieved when there are no points of intersection of the two above planes on the product. Well, if the transfer plane goes beyond the center of the width, this overhang is called negative (see photo).

Is ET the only value used to mark modern cars?

It is also worth noting that only German manufacturers use the abbreviation ET to mark disc offset. By the way, if the offset parameter is negative, a hyphen is placed before the company number, and in our case the marking will be as follows: ET-30. If this is a positive departure, instead of ET the company writes YT. France marks departures with the word “DEPORT”. The offset and bolt pattern of the rims of the Hyundai Accent and many other cars on the world market is designated as “OFFSET”.

Why is the offset parameter so important for a car?

Its essence lies in the fact that if the offset does not match, the disc simply cannot be installed on the car - some elements and parts of the suspension prevent this. When the offset is negative, the risk of the wheel coming out beyond the wheel arches of the car increases. Conversely, if this value is positive, the tire will “hide” behind the arches.

How is wheel bolt pattern measured?

This is not very difficult to do - just study a special table that contains data on the bolt pattern of specific car brands. However, it does not always contain the required information, so sometimes you have to measure the data yourself. Below we will look at how to do this. It will be easiest for us with the first indicator (the one after the fraction). It can be determined with the naked eye - you just need to count the number of bolts and remember this value. It will be more difficult later. Since the bolt pattern of wheel rims (Chevrolet Cruze included) includes the parameter of the diameter of the bolt placement circle, we will need to use a special formula when calculating. It is different for all wheels. So, for example, for disks with three bolt holes, you need to apply the formula B = Ax1.155. In this case, the value A is the distance between adjacent holes. For four holes – B=Ax1, 414; for five – B=Ax1.701. When measuring the distances between adjacent bolts, it is impossible not to do without a special device - a caliper. Add the diameter value to the data obtained. As a result, you will know the diameter of the circle where the bolts are located, that is, the value B.

Don't forget to check the information

It is very important to pay attention to the accuracy of the measured data. The bolt pattern of wheel rims (Daewoo Nexia as well) must contain extremely accurate information. And since in this aspect there are very close values ​​(110, 112, 114), the risk of confusing them is extremely high. But even the slightest discrepancy in the bolt pattern can ruin the chassis system and steering!

Additional Information

In order to find out the diameter of the hole for the hub, you need to use a ruler to measure the adapter ring with which it is centered. But it is not necessary to measure all of these data yourself - some of them are already written in the technical passport of the car. The disc bolt pattern can also be indicated on the spare wheel on the inside of the stamped disc. But manufacturers do this only with a spare wheel - even on branded steel elements the company does not indicate the bolt pattern parameter. Most often, the surface of stamped discs indicates the month and year of their production, as well as the emblem or inscription of the manufacturer. There are no symbols on the inside at all. In this case, you can contact an official dealer and find out from him the exact bolt pattern parameters for a specific car make.

Pay attention to the table and compare the results

To be confident in the data obtained from independent measurements, you should check the information with the tabulated values. If you have, for example, a Mercedes, and the parameters you obtained are 111 millimeters, use the tabular numbers (112 millimeters), since the German Mercedes does not produce wheels with a bolt pattern of 110 or 111 mm. The domestic auto industry also has its own values ​​regarding these parameters. For example, the bolt pattern of VAZ wheel rims is 4x98 millimeters. That is, if during independent measurements you come up with a value of 99 or 97, we focus primarily on the tabular data. But not all VAZs have such a bolt pattern. For example, on the Niva 2121 series this parameter is 5×139.7. By the way, on most European foreign cars this value is the same (it is one hundred millimeters) regardless of body type, year of manufacture, generation and engine size.

Is a slight deviation acceptable for cars and SUVs?

Regarding the wheel bolt pattern, we can say that deviations between the values ​​can be acceptable, but within no more than one or two millimeters. Thus, it is quite safe to install a disk with a diameter for mounting bolts of 100 millimeters on passenger VAZs (but no more than that!). If this figure is already 101 millimeters, no one can guarantee your driving safety, and the chassis system will be subject to heavy loads. Therefore, try to select products that are as similar as possible in this parameter to the factory ones.

Conclusion

So, we found out what wheel rim looseness is and what importance it has for a car. Now you understand the consequences of choosing wheels with the wrong offset, as well as how to measure these parameters yourself. Knowing all the basic parameters of the markings and their explanation set out in this article, you can easily select auto wheels (cast and forged) specifically for your vehicle model, regardless of whether it is an SUV or a passenger car.

General background information

Ranges of possible values ​​for tires and wheels Daewoo Nexia 2004.
Tires

Wheel disks

Photo

Expert advice

When choosing tires for a car, you must first follow the manufacturer's instructions. Ask yourself a few questions.

• On what roads will the car be primarily used?
• Do you need increased cross-country ability?
• How much of the route will be city roads and how much will be highways?
• Will the vehicle carry heavy loads?

The answers to these and similar questions will help determine which tire parameters you need to pay special attention to.

How to choose the right wheels for Daewoo Nexia 2004?

3 types of rims:

• Stamped (economical price category) - made from a sheet of iron by stamping on a press.
• Light alloy - manufactured by casting (more reliable than stamped ones).
• Forged (the highest quality and more expensive than the previous ones) - made from light alloys by stamping at high temperatures.

The choice depends on financial capabilities. However, it should be borne in mind that the quality of the road surface on which you have to drive every day must also be taken into account.

So, if it gets into a hole, a stamped disk will bend and will not cause harm to the tire, but a forged or cast one can cut it. There is a possibility that the cast disc may burst or crack.

It should also be noted that repairing “stamping” wheels is cheaper than repairing cast or forged wheels. But wheels with high-quality cast and forged disks kill the suspension less, because lighter and have more perfect geometry (better balanced).

The same wheels may or may not rub with tires on the same car - wheel alignment adjustment will help here.

What is the tire pressure?

It is the driver's responsibility to constantly monitor tire pressure. This will avoid standard problems associated with vehicle operation. An abnormal pressure value often causes:

• deterioration of management;
• uneven tread wear.

Often the car owner independently reduces the pressure in the wheels of his own vehicle. This reduces the load on the suspension, and the car “passes” various road irregularities an order of magnitude easier. But it is worth noting: a decrease in pressure even by 0.1 MPa leads to serious problems. The main ones include:

• increased fuel consumption;
• rapid wear of the outer tread segments;
• the car becomes less maneuverable.

An overinflated wheel causes no less problems. The central part of the cylinder begins to wear off quickly. In addition, at ambient temperatures of more than 60 degrees Celsius, the tire may simply explode. Which will lead to driving into the oncoming lane.

Tires and wheels for Ravon R3 Nexia

Wheels are an integral part of any car, and sooner or later they have to be replaced, most often it’s just the tires, as they gradually wear out, but sometimes you have to buy wheels, as they can be deformed. In addition, in our country you need to change tires according to the season, i.e. for summer these should be summer ones, and for winter - winter ones, studded or so-called “Velcro”. It’s most convenient to have a set of wheels so that when the next season comes you can quickly change them, literally in half an hour.

To purchase wheels for your Ravon P3, you will need to know certain parameters so that they fit the car and perform their functions correctly.

Size of standard Ravon R3 wheels and tires

Depending on the configuration, two types of rims are installed on the Nexia:

• Stamped (R14 and R15);
• Light alloy (R15);

General characteristics:

• Bolt pattern: 4x100 ;
• Size: CO: 56,59;
• Nut dimensions: M12x1.5 ;
• Reach: 45 mm (+/- 1) ;

The basic version of the R3 is equipped with steel wheels with a diameter of 14 inches, the rim width of which is 5.5 inches, with 185/60 tires.

The average “Optimum” configuration also has the usual steel “stampings”, but their diameter is increased to 15, and the rim width is up to 6 inches. The tires are the same in width - 180mm, but the profile height is slightly less - 55%. The kit also comes with a set of hubcaps, thanks to which the appearance of the wheels is slightly transformed.

The most beautiful wheels with alloy wheels made of aluminum are presented in the most complete version “Elegant”, they have the same size as the previous ones, i.e. 185/55/R15.

As a result, we get two standard sizes for Ravon P3, which are provided by the manufacturer:

Discs

Appearance of the sedan on steel wheels:

Photo with factory alloy wheels 185/55/R15

Non-standard wheel sizes for Ravon P3

ATTENTION! When installing wheels or tires of a non-standard size, you do so “at your own peril and risk.” It is difficult to predict how the car’s characteristics will change, since the model was initially tested exclusively with standard sizes.

The Ravon R3, as you know, is built on the basis of the Chevrolet Aveo T250, which had a greater variety of sizes; in addition, many car enthusiasts have already tested this car with a wide variety of tire and wheel parameters; you can read reviews about them on specialized forums. Below we have collected the most popular options that car owners install on their Ravona.

• 6.5Jx14ET42
• 6.5Jx15ET42
• 7Jx15 ET38
• 7Jx16 ET38
• 7.5Jx16ET35

• 205/55R14
• 205/50R15
• 215/45R15
• 215/40R16
• 225/40ZR16

The main thing is to check the bolt pattern (PCD), it should be 4x100, if it is different, then you simply will not be able to tighten the bolts, since it will not coincide with the holes on the hub.

If possible, also try to choose wheels so that the size of their central hole is also standard - 56.59mm. But if you cannot find the same one, then you will definitely need centering (spacer) rings that can level out the difference.

Source: https://nexia-ravon.ru/shinyi-i-diski-na-ravon-r3-nexia/

Minimum and maximum tire sizes for Daewoo Nexia

The minimum possible installation, according to the manufacturer's recommendations, is diameter R14. If necessary, products R15 and R16 can be installed without problems. You can operate a car on enlarged wheels without any problems, this is confirmed by many years of experience of a huge number of fans of the brand

When increasing the diameter of the rim, it is important to reduce the height of the tire profile and measure so that there is no contact or friction with the wheel arch structure

Of course, this will not improve the ride comfort and dynamics of the car, but it will definitely improve the appearance. With such products it is advisable to install tires with dimensions 205/40 R17. The car will become more stable on the road and gain improved handling. This will also improve fuel consumption.

You can select high-quality wheels for a Daewoo Nexia only taking into account the drilling parameters for it, which is 4x100. There are a huge number of products with such data on the Russian market.

Video about choosing wheels for Daewoo Nexia

Every car owner often thinks about changing the appearance of his own car. High-quality tuning implies the installation of body kits and a significant change in engine characteristics.

However, you cannot completely change the appearance of the car - for example, you can only replace the rims. When choosing such a part, you should pay attention not only to their diameter, width and offset, but also to such auto characteristics as bolt pattern.

What does the bolt pattern look like in the diagram?

How is the wheel bolt pattern measured on Daewoo cars?

When you have to select and purchase new wheels for the Nexia, you need to know the drilling parameters on the car in advance. The most accessible way to determine it for any car brand is to use a special table that can be found on the Internet. It contains, depending on the year of manufacture and engine size, all the necessary parameters and dimensions.

The third method is the least accurate and most labor-intensive. In this case, you can independently measure all the required dimensions. To determine the bolt pattern depending on the number of fasteners, you will need to apply the following formulas:

• B=A×1.155 - used for three holes;
• B=A×1.414 - calculated for four holes;
• B=A×1.701 - for five holes.

Having received the value of the required value, you can easily calculate the required diameter size, which is designated as B.

Comparison of the results obtained with the table

It is advisable to compare the data obtained as a result of measurements with the values ​​​​indicated in a special table. For example, for a Mercedes car, the obtained results of 111 millimeters increase to 112 - the German concern simply does not produce wheels with a bolt pattern of 111 millimeters. Domestic automakers also adhere to certain values ​​for these parameters. In the case of a VAZ, the value is 4x98 mm. Regardless of the data obtained as a result of measurements, you need to focus on the table. However, such precise parameters are not found in all cars: for example, for the Niva the bolt pattern is 5x139.7. In addition, for many foreign-made vehicles the indicator is the same, regardless of the make, model, engine size or year of manufacture.

Possibility of deviation of values

As for the disc bolt pattern, there may be deviations in size, but provided that they do not exceed one or two millimeters. For example, it is quite possible to install rims with bolt diameters of 100 millimeters on domestically produced passenger cars. 101 millimeters is already a serious cause for concern and a reason for a significant reduction in travel safety and increased load on the vehicle’s chassis system. For this reason, it is advisable to select those products whose bolt pattern characteristics will be as close as possible to their factory counterparts.

Bolt pattern of Nexia rims

The production of this model of the South Korean brand began in 1994. The Opel Cadet car was taken as a basis, slightly modernized and adapted to modern realities. Subsequently released in countries such as Vietnam, Egypt, Romania and Uzbekistan. In the latter case, the production of these machines was finally stopped in 2021.

Selecting and purchasing high-quality wheels for the Daewoo Nexia is not difficult. Many brands on the market are suitable for this car model. You can choose products to suit every taste and budget. The most common are stamped wheels, but cast ones can also be purchased if desired. Products of any design, color and shape are presented.

The size of the wheels for the Daewoo Nexia from the factory can be in three designs, with diameters from 13 to 15 inches. But if necessary, it is common among tuning enthusiasts to install even R16 wheels. For this, special spacers are used. Regardless of the country of manufacture and year of manufacture, the wheel bolt pattern for Daewoo Nexia is the same and equal to 4x100.

Almost all cars were equipped with stamped wheels from the factory. Some of the most expensive versions came with R15 alloy wheels.

Tire and spare parts stores offer a huge number of different products for tuning this car. You can replace certain components and install improved ones that are sporty and visually attractive. The main criterion on which the appearance of a vehicle depends is the wheels. Wheels are replaced with ones that are larger in size and improved in quality.

However, it is important that wheels of increased diameter do not reduce the performance of the machine

A new set of products must comply with all factory parameters and characteristics. The wheel bolt pattern for Nexia must be taken into account as the most important indicator when selecting new products. It is also necessary to select and install the right tires, because even on the highest quality wheels, cheap tires will ruin everything, and the benefit will not be felt at all. The bolt pattern parameter also determines whether it is possible to install a certain model of wheel rims on a car. If the parameter is not suitable, then special adapter rings should be installed.

Extra options

To install a wheel of a different bolt pattern, special “adapters” are used - spacers.
The diameter of the hole for the hub is measured by measuring the adapter ring. It is not necessary to run around the car with a ruler - almost all the data is indicated in the technical passport. The disc bolt pattern, for example, can be indicated on the inside of the product. However, manufacturers indicate it this way only on the spare wheel.

In most cases, the marking of stamped discs includes the manufacturer, its emblem and the date of manufacture of the product. As an option, you can contact an authorized dealer for the relevant information and find out the bolt pattern parameters for a specific make and model of the car.

What is disc bolt pattern?

The bolt pattern determines whether the disc can be installed on a car.

Each wheel rim is characterized by a mass of geometric values, which many have no idea about. In vain, because it is absolutely not enough to know the number of holes for bolts and the diameter of the disk. A bunch of other parameters affect both safety and the service life of the car’s chassis, suspension and tires. And here every fraction of a millimeter is important.

Basic parameters of the wheel rim.

1. The seat width of the wheel is measured in inches.
2. Landing diameter. Also measured in inches.
3. The distance from the mounting surface of the disk to the center of the tire. Designated ET.
4. The number of holes for fasteners and the diameter at which their centers are located. Most often, this parameter is called a bolt pattern, but this is not entirely true. The parameter is designated as Pitch Circle Diameter or PCD.
5. The diameter of the disk mounting hole, the one that fits on the hub. It is designated DIA and measured in millimeters.

The PCD parameter depends on the distance between the centers of adjacent holes and on their number.

What kind of chatter does the Daewoo Nexia have?

To understand this whole geometric compote, let’s look at examples with disks for Nexia. As a rule, Nexias of different years of production are equipped with wheels with a diameter of 13 and 14 inches. Here are their parameters:

• 13/5J PCD 4×100 ET 49 DIA 56.6
• 13/5.5J PCD 4×100 ET 49 DIA 56.6;
• 14/5.5J PCD 4×100 ET 49 DIA 56.6.

Stamped standard 13-inch wheel for Nexia.

Now the markings of a standard Nexia disk become clear:

1. 13 and 14 are the diameter of the disc, measured in inches.
2. 5.5J (5J) or simply 5.5 (5) is the width of the rim in inches.
3. PCD 4×100 - four holes, the centers of which are located along a diameter of 100 mm.
4. ET 49 - the distance from the mounting surface of the disk to the center of the tire is 49 millimeters.
5. The landing diameter of the hub hole is 56.6 mm.

A set of 14-inch wheels for the Daewoo Nexia with a standard bolt pattern.

Alternative options

This is a standard bolt pattern for Nexia with 13 and 14 discs. If desired, you can also install 15-inch wheels if their parameters are as follows: 15/6.0J PCD 4×100 ET 40 DIA 56.6.

It is clear that the ride on such wheels will not be comfortable, but it looks very impressive. Note that in any case the PCD and DIA parameters remain unchanged. The issue with offset is complicated, since the parameter cannot but take into account the width of the disk. If the offset is too large with a large diameter and large width, the rubber will inevitably reach the fender liners and wheel arches. And vice versa - if the offset is insufficient, but the wheels are wide and large in diameter, when turning we will scratch the tires against the suspension parts.

Proven replacements

Alloy wheel for Daewoo Nexia GM12 (copy of the original disk).

Proven options for replacing factory disks:

• 6Jx14 4×100 ET45;
• 6Jx15 4×100 ET45;
• 5Jx15 4×100 ET45;
• 5Jx16 4×100 ET45;
• 7Jx15 4×100 ET45;
• 7Jx16 4x100 ET45.

Theoretically, it is possible to install disks of a different bolt pattern using adapters, but is it worth doing?

Wheel bolt pattern Daewoo Nexia 2009 1.6 (109 hp, gasoline)

1. Razboltovka.ru
2. Daewoo
3. Nexia
4. 1.6 (109 hp, gasoline)
5. 2009

Find disk parameters for Daewoo Nexia 2009, 1.6 (109 hp, petrol).

Table of parameters and wheel bolt patterns of the Daewoo Nexia 1.6 model (109 hp, gasoline) - 2009.

Disc drilling parameters are usually called bolt pattern:

• LZ (number of holes)
• PCD (hole center circle diameter)
• ET (disc offset)
• DIA (hole diameter)

Save just in case so as not to lose! Make model modificationAuto Year of manufacture Wheel width Wheel diameter Bolt pattern LZ*PCD Offset ET DiameterDIA Installation type

razboltovka.ru

What is disc bolt pattern?

The bolt pattern determines whether the disc can be installed on a car.

Each wheel rim is characterized by a mass of geometric values, which many have no idea about. In vain, because it is absolutely not enough to know the number of holes for bolts and the diameter of the disk. A bunch of other parameters affect both safety and the service life of the car’s chassis, suspension and tires. And here every fraction of a millimeter is important.

Basic parameters of the wheel rim.

• The seat width of the wheel is measured in inches.
• Landing diameter. Also measured in inches.
• The distance from the mounting surface of the disk to the center of the tire. Designated ET.
• The number of holes for fasteners and the diameter at which their centers are located. Most often, this parameter is called a bolt pattern, but this is not entirely true. The parameter is designated as Pitch Circle Diameter or PCD.
• The diameter of the disk mounting hole, the one that fits on the hub. It is designated DIA and measured in millimeters.

The PCD parameter depends on the distance between the centers of adjacent holes and on their number.

What kind of chatter does the Daewoo Nexia have?

To understand this whole geometric compote, let’s look at examples with disks for Nexia. As a rule, Nexias of different years of production are equipped with wheels with a diameter of 13 and 14 inches. Here are their parameters:

• 13/5J PCD 4×100 ET 49 DIA 56.6
• 13/5.5J PCD 4×100 ET 49 DIA 56.6;
• 14/5.5J PCD 4×100 ET 49 DIA 56.6.

Stamped standard 13-inch wheel for Nexia.

Now the markings of a standard Nexia disk become clear:

• 13 and 14 are the diameter of the disc, measured in inches.
• 5.5J (5J) or simply 5.5 (5) is the width of the rim in inches.
• PCD 4×100 - four holes, the centers of which are located along a diameter of 100 mm.
• ET 49 - the distance from the mounting surface of the disk to the center of the tire is 49 millimeters.
• The landing diameter of the hub hole is 56.6 mm.

A set of 14-inch wheels for the Daewoo Nexia with a standard bolt pattern.

Alternative options

This is a standard bolt pattern for Nexia with 13 and 14 discs. If desired, you can also install 15-inch wheels if their parameters are as follows: 15/6.0J PCD 4×100 ET 40 DIA 56.6.

It is clear that the ride on such wheels will not be comfortable, but it looks very impressive. Note that in any case the PCD and DIA parameters remain unchanged. The issue with offset is complicated, since the parameter cannot but take into account the width of the disk. If the offset is too large with a large diameter and large width, the rubber will inevitably reach the fender liners and wheel arches. And vice versa - if the offset is insufficient, but the wheels are wide and large in diameter, when turning we will scratch the tires against the suspension parts.

Proven replacements

Alloy wheel for Daewoo Nexia GM12 (copy of the original disk).

Proven options for replacing factory disks:

• 6Jx14 4×100 ET45;
• 6Jx15 4×100 ET45;
• 5Jx15 4×100 ET45;
• 5Jx16 4×100 ET45;
• 7Jx15 4×100 ET45;
• 7Jx16 4x100 ET45.

Theoretically, it is possible to install disks of a different bolt pattern using adapters, but is it worth doing?

Wheel bolt pattern Daewoo Nexia 2010 1.5 (80 hp, gasoline)

1. Razboltovka.ru
2. Daewoo
3. Nexia
4. 1.5 (80 hp, gasoline)
5. 2010

Find disk parameters for Daewoo Nexia 2010, 1.5 (80 hp, petrol).

Table of parameters and wheel bolt patterns of the Daewoo Nexia 1.5 model (80 hp, gasoline) - 2010.

Disc drilling parameters are usually called bolt pattern:

• LZ (number of holes)
• PCD (hole center circle diameter)
• ET (disc offset)
• DIA (hole diameter)

Save just in case so as not to lose! Make model modificationAuto Year of manufacture Wheel width Wheel diameter Bolt pattern LZ*PCD Offset ET DiameterDIA Installation type

razboltovka.ru

What it is? Characteristics of the bolt pattern

The wheel bolt pattern is the diameter of the holes intended for the bolts. Abroad, this characteristic is designated by the abbreviation PCD. Why is this parameter important for a car? If the bolt pattern of the wheel rims does not match the specific car model, they will be installed off-axis. Of course, this will not affect the appearance of the vehicle in any way, but the technical part will suffer to the fullest. When the car moves, discs mounted off-axis destroy elements of the steering mechanism and suspension. Neglecting this parameter can lead to the wheel turning loose while driving, which will certainly lead to a traffic accident.

Characteristics

Let's look at the wheel bolt pattern for the Daewoo Nexia according to the manufacturer's data by year of manufacture and generation:

Alloy wheels are beautiful, impressive and original. This is not to say that this is very practical on our roads, although many owners of mass-produced cars are thinking about investing a tidy sum in alloy wheels for their one and only. It’s tempting, but before that you need to weigh and calculate everything. The wheel bolt pattern for our Daewoo Nexia is the number one issue in this case. First the bolt pattern, and then the design.

How is the wheel bolt pattern measured on Daewoo cars?

When you have to select and purchase new wheels for the Nexia, you need to know the drilling parameters on the car in advance. The most accessible way to determine it for any car brand is to use a special table that can be found on the Internet. It contains, depending on the year of manufacture and engine size, all the necessary parameters and dimensions.

The second method, which is both the most correct and accurate, can be called taking data from the car’s instructions or other technical documentation that comes with the kit.

The third method is the least accurate and most labor-intensive. In this case, you can independently measure all the required dimensions. To determine the bolt pattern depending on the number of fasteners, you will need to apply the following formulas:

• B=A×1.155 - used for three holes;
• B=A×1.414 - calculated for four holes;
• B=A×1.701 - for five holes.

Having received the value of the required value, you can easily calculate the required diameter size, which is designated as B.

Choosing wheels for Nexia

All car enthusiasts know that with the arrival of a new season, tires require mandatory replacement, but as for the rule that each type of tire corresponds to a certain type of wheel, a slightly smaller number of drivers are familiar with it. This attitude can lead to the tires deteriorating after the first visit to the tire shop.

Sometimes vehicle owners assume that different types of wheels differ from each other only in price and diameter. However, this is not true, because the size of disks on Nexia is not the most important indicator.

Discs must be durable not only when driving on asphalt, but also in the event of any kind of load.

In addition, they must have a reduced weight, since the smoothness of the ride, dynamism, vehicle controllability and other indicators directly depend on it.

Disk parameters for Nexia

To make the right decision, you should study the required disk parameters before making a choice. Then you will understand which type of wheels you will choose: alloy, stamped or forged.

In order to make the process of choosing wheels for Daewoo Nexia more convenient, below is a table that shows what positive and negative qualities Replica wheels have, depending on the materials and method of their manufacture.

After you decide which wheels to buy for the Nexia: alloy, forged or stamped, you will need to figure out one more thing - the size of their rims. Its width should be no more than 30 percent of the tire profile.

In addition, it is worth noting that it is undesirable to use too wide or, conversely, very narrow rims, since there is a high probability of violating the designed tire profile. And this, as is known, can lead to a deterioration in the driving performance of the car.

When choosing wheels for the Nexia, do not forget that certain brands of tires are also preferable for it, for example, Dunlop tires. Their distinctive feature is ensuring maximum comfort, reduced noise levels, durability and excellent handling.

In addition to Dunlop tires, Daewoo Nexia is also suitable for tires from other manufacturers. For example, it won’t be difficult to buy Cooper tires from you, since among the wide variety of winter, summer and off-season tire models from this manufacturer, there are brands that are ideal for Daewoo Nexia.

Source: https://pieman.ru/vibiraem_diski_na_neksiyu

How to choose original wheels

First you need to decide on seasonality. For winter, it is recommended to buy wheels one or two inches smaller than for summer.

Maximum safety while driving will be provided only by original rims. A good level of safety is also ensured by products from proven quality brands. It is not advisable to experiment with replicas or used wheels.

For Daewoo Nexia of any year of manufacture there are no problems with the selection of wheel rims of any size. Both cast and stamped products can be installed.

Parameters of alloy wheels

PCD (Pitch Circle Diameter) diameter and the number of these holes.

For example, PCD100/4 - 4 holes with a diameter of 100 mm.

• 
  Parameters of stamped wheels for a VAZ 2114 car

Since the mounting holes are made with a significant tolerance plus in diameter, you can make a mistake in choosing a PCD if it differs from the standard one by a couple of millimeters. For example, a PCD98/4 wheel is often put on a hub with PCD100/4 (98 mm from 100 cannot be distinguished by eye). It is unacceptable. In this case, of all the nuts (or bolts), only one will be fully tightened; the remaining holes will “lead away” and the fasteners will remain untightened or tightened skewed - the fit of the wheel on the hub will be incomplete. While driving, such a wheel will “beat”, in addition, not fully tightened nuts will unscrew by themselves.

Determining PCD by distance between bolt holes

DIA - diameter of the central hole for the hub or the central hole of the disk

ET - offset (or offset) of the disk (measured in mm).

This is the distance between the longitudinal plane of symmetry of the disk and the plane of the hub. The offset can be zero (the plane of symmetry of the disk coincides with the plane of the machine hub), positive (the plane of symmetry of the disk is closer to the center of the machine than the plane of the hub - as in the figure) and negative (further). For each car model, the offset is calculated by the manufacturer to ensure optimal stability and controllability of the car, as well as the least load on the hub bearings. The Germans designate the offset ET (for example, ET30 (mm), if its value is positive, or ET-30, if negative), the French - DEPORT, manufacturers from other countries usually use the English OFFSET. The desire to install wider low-profile tires that have appeared in recent years (sometimes on larger R-size wheels) leads to the need to select a wheel with a reduced ET (i.e. the tire has become wider - you need to move it outward from the body - otherwise it will start to touch it ) . Reducing ET makes the wheel track wider; - this increases the stability of the car and gives it a stylish racing look. An excessive decrease in ET is undesirable, because may result in increased load on the wheel bearings. Increase the reach, i.e. It is usually impossible to narrow the track - the disc will rest against the brake caliper.

More details about bolt pattern

There are not so many PCD sizes: about a dozen popular ones, on European and Asian cars, and a few more rare ones, which are found mainly on American cars.

There is very little difference between some of them: 98 and 100, or 112 and 114.3. Visually, it is almost invisible, and when they see a wheel model they like, car owners sometimes think that one option can be replaced with another.

This is an erroneous opinion, and such a decision will result in a poor fit of the disk to the hub or its misalignment. Problems will not keep you waiting.

Let's consider what options for placing mounting holes are found on certain cars: