We remove the vacuum brake booster on a VAZ-2110 with our own hands for replacement

Troubleshooting the vacuum booster

Devices from different manufacturers may vary in characteristics and quality, and the price of the VAZ 2110 vacuum amplifier may also vary. Since the functioning of its mechanism affects the operation of other parts and components, and above all the car engine, it is worth not saving and carefully monitoring its serviceability.

If there is a hissing sound from under the hood, a burnt smell of oil is felt in the cabin, and the brake works like a stopped car only after repeatedly pumping the brake pedal with your foot, then you should immediately contact a car service center for diagnostics and, if necessary, replacement of this device.

You can test the “tens” vacuum brake booster for proper operation yourself. To do this, press the brake pedal repeatedly with the engine off. This method checks the uniformity of pressure in the cavities. Everything is fine as long as the valve body does not jam.

Then, when you hold your foot on the brake pedal, the engine starts. If the pedal is moved forward simultaneously with the foot, then the amplifier is operational. Otherwise, you need to make sure that the problem is this and not a problem with the tip flange or its fastening.

The pedal may still not function properly due to a faulty connection of the fitting on the engine exhaust pipe to the hose. This also has a detrimental effect on the performance of the braking system and its effectiveness.

Diagnostics

In fact, the failure of the vacuum brake booster is not very harmless. Especially if the failure occurs unexpectedly. The first sign of a breakdown is the brake pedal becoming sticky. If this pedal has become much harder than it was before, then it makes sense to check the amplifier. Most likely, he simply cannot cope with his responsibilities. Often, when you press the brake, you can hear a hissing sound.

Diagnosing such a malfunction is very simple. To do this, with the engine turned off, press the brake pedal 5-6 times and leave it pressed. After this, we start the engine. The pedal should go down a little, this indicates that the brake vacuum is fully operational. If the brake pedal does not go away, then most likely there is a problem with the booster. First, check all hoses and fittings for air leaks. After that, run the diagnostics again. If nothing has changed, then it makes sense to replace the entire amplifier.

Article on the topic “How to check the vacuum brake booster?”

VUT and GTZ Priora on VAZ 2110

You can improve the standard brakes of a VAZ 2110 in various ways, and in this photo report we will look at how to install a Vacuum Brake Booster (VUT) and a Brake Master Cylinder (MCC) from a Lada Priora or Kalina on a “top ten” with your own hands. Required:

1. VUT and GTZ Priora or Kalina
2. 2 tees from classics
3. 4 nuts x 8 for attaching the GTZ and pedal assembly to the VUT (the old ones are not suitable, they are larger)
4. One-face brake bleeding device.
5. 2 tubes from Priora with fittings 12x1 and 10x1 on the GTZ side, and 10x1.25 on the tee side.
6. Brake fluid.

The photo shows:

1. On the left is the Prirovskaya tube 12x1.0, and on the right is the “tens” 10x1.25
2. On the left is a VAZ 2110 10x1.25, and on the right is a Prirovskaya 10x1.0
3. General view of both tubes

If you want the replacement to take place with minimal alterations, then it is better to buy the VUT, GTZ and pedal assembly from the Priora. We dismantle the frill and remove the right half of the sound insulation of the engine compartment, the left one can simply be bent. Drain the brake fluid and unscrew the brake pipes.

In the cabin, remove the terminals from the brake light end switch and unscrew the 4 nuts securing the VUT to the body. Now you can easily remove the VUT and GTZ. If you couldn’t buy a prefabricated kit, then you need to install the pedal from the old VUT into the new one. Next, we assemble the VUT and GTZ into one unit and see that the pedal with standard mounting holes for the VUT will be rotated 90 degrees relative to the vertical position of the brake fluid reservoir.

To rotate the pedal to its normal position, you need to re-drill the mounting holes in the pedal assembly. We apply the pedal to the VUT and carefully mark where new holes need to be made. We try on and, if necessary, correct the resulting holes with a drill or file. The fastening nut is circled in red in the top photo. We screw the pedal assembly to the VUT. A few photos of the process:

1. VUT and GTZ and pedal assembly
2. Attaching the pedal to the VUT, the nut is inside, it is not easy to tighten
3. The other side of the pedal was much easier
4. VUT and GTZ assembled

We recommend: Should you change the engine oil if it turns black?

The resulting structure is installed in the car. There was no need to cut the frill, everything was installed as original. We install the tees. We screw the Priorov tubes to the GTZ and tees. We fasten the tees to each other with a pin, preferably 5. We replace the “sorcerer” (brake force regulator) using a pit. We unscrew the brake pipes from it, remembering where they were, and remove it by unscrewing 2 bolts.

We install a new “sorcerer” instead of the old one and screw on all the pipes. We insert a screwdriver into it in advance and return to the brake pipes. We fill the brake fluid into the reservoir. To remove air from the brake system, you need to tighten the tubes in the tees not completely (leaving a gap). We blow something into the brake fluid reservoir and wait until air stops coming out of the cracks between the tubes and tees. Then we tighten it. Don't forget to bleed the brakes and adjust the sorcerer. Immediately adjust the VUT rod.

After installing the Priorovsky VUT and GTZ on a car of the tenth family, at first you will have to get used to the new brakes (much less force on the pedal is required than before), but you will quickly get used to the good ones. For the result obtained, it is desirable to have good brake discs for 14 or 15 and brake pads. By the way, you can get a similar result by modifying the standard VUT.

The process of replacing the vacuum booster on a VAZ-2110

Vacuum brake booster.

To replace a vacuum brake booster, you must have some knowledge of vehicle design. On a VAZ-2110 it is not so difficult to replace a part with your own hands.

You need to stock up on a set of tools - keys and screwdrivers and you can begin the procedure. Let's consider, step by step, the process of replacing the vacuum brake booster of the VAZ-2110:

1. Remove the negative terminal from the battery.
2. Disconnect the wire block on the brake fluid level sensor.

   Disconnect the power from the brake fluid level sensor.

3. We hold the vacuum booster return valve and with the other hand remove the hose from it.

   Unscrew the hose from the check valve.

4. Remove the master brake cylinder. There are only two nuts, but they can stick.

   In the engine compartment, you need to unscrew the two fastening nuts of the brake master cylinder.

5. Without disassembling the brake, namely, without disconnecting the brake pipes, we move the master brake cylinder to the side.

   We remove the cylinder with tubes from the amplifier.

6. From the interior side, unscrew the four nuts securing the brake pedal bracket.

   We remove the vacuum booster mounts from the passenger compartment.

7. After this, you can dismantle the vacuum booster.
8. Using a screwdriver, remove the locking plate of the pin. We push out the finger and disconnect the vacuum booster pusher from the pedal.

   Remove the locking plate with the finger.

   Read also:  VAZ 2103-06: Working brake system. Vacuum booster
9. Next, we are interested in the two nuts securing the amplifier to the plate, unscrew it, most likely you will have to use wd-40. We dismantle the bracket.

   After unscrewing the fasteners, remove the bracket.

10. Assembly is carried out in the reverse order of disassembly.

This is what the engine compartment looks like without an amplifier!

Part selection

Amplifier Torgmash.

The original catalog number of the VAZ-2110 vacuum brake booster is 21103510010.

The price of this part is 4000 rubles. In addition, there are a number of analogues that can be used. Thus, the automotive market offers the following non-original parts:

• Pekar 2110-3510010 with an average cost of 2500 rubles.

  Pekar 2110-3510010 is an amplifier with a sporty twist.

• DK 2110-3510010 - low quality and cost around 2000 rubles.
• Master-sport 2110-3510010 is an expensive but high-quality product.

  Vacuum brake booster master-Sport

Symptoms of malfunction (check options)

There are several signs of a malfunction of the vacuum brake booster, and, accordingly, diagnostics of performance. Let's consider each of the options:

1. We start the engine and let it run for a few minutes, after which it is necessary to turn it off. Press the brake pedal several times. During normal operation of the amplifier, the pedal will be depressed the first time, but subsequent times the stroke will be less and less. If the pedal stroke does not decrease the second and subsequent times, then there is a breakdown in the system and the part is not sealed. This means that the vacuum booster needs to be replaced.
2. The second option assumes that the first option did not produce any results, and doubts have crept in. Depress the brake pedal and start the engine. With this turn of events, after starting the power unit, the pedal should go all the way down. If this does not happen, then there is an air leak and the amplifier does not work.
3. With the engine running, hold down the brake pedal and then turn off the engine. Hold the pedal for another 1.5-2 minutes without releasing it. If there are malfunctions, the pedal will rise.

The amplifier has gaskets and O-rings, and these are the ones that most often fail.

We recommend: How to make a heated steering wheel with your own hands?

Which vacuum cleaner to buy

Brakes are the most important system in a car. Repairs should be approached responsibly. The vacuum booster is an expensive unit. Therefore, the owner may have the idea of ​​buying a used spare part. In this case, you can really save money. But, the old vacuum seal can fail at any minute, which means the money was wasted. In addition, disassembling the VAZ 2110 and then replacing the vacuum seal may be in vain.

Consumer choice

Troubleshooting

When the identified signs indicate a malfunction of the VAZ 2110 vacuum brake booster, you can try to provide first aid to your car yourself. In normal condition, the braking system should hold it in place at an inclination of 25º to a horizontal surface. If it doesn’t cope well, you should loosen the locknut and tighten the cable.

Then you need to check the full lever stroke, it is necessary that it is approximately 2-4 teeth. After tightening the locknut tightly, it is worth performing a series of safety brakes while simultaneously monitoring the stroke of the lever. Moreover, the rotation of the wheels when the lever is lowered to the end should be free, without force. If such a test reveals the inability of the amplifier to cope with braking, this indicates the need to replace it.

Many car services provide such a relevant service today as tuning the brake system of the VAZ 2110; the price of the unit in case of replacement is still higher than its improvement. It also affects the rear brake discs, in addition to the booster, which is upgraded by installing a special washer. This seemingly insignificant detail can significantly influence the operation of the amplifier and the braking process as a whole.

When the driver presses the brake pedal, the rod passing through the washer begins to exert pressure on the brake master cylinder. Because of this, the operation of the bypass valves begins a little later. Thus, installing a washer makes braking smoother, the pedal is softer, and its reaction in case of a sudden stop does not change.

But if a hiss has already appeared, the engine stalls when the brake pedal is pressed, or it has become very tight, it is necessary to replace the mechanism. Otherwise, driving such a car becomes unsafe for yourself and others. In preparation for replacing this unit, the rear of the engine compartment must be disassembled and the elastic seal, trim and frill removed.

The process begins by disconnecting the pad wiring from the sensor indicating the brake fluid level. While supporting the check valve, disconnect the hose from the amplifier. Next, unscrew both fastening nuts of the master cylinder of the braking system. It is smoothly turned away from the amplifier to the distance required to remove the latter, and this is done without removing the brake pipes.

Under the instrument panel located in the passenger compartment, you should unscrew all four fastening nuts of the brake pedal bracket, which is quite difficult due to their inconvenient location. Then the wires, bracket and amplifier itself are removed in the engine compartment at the same time as the brake pedal assembly.

Having disconnected the two fastening nuts, use a screwdriver to remove the locking plate of the mounting pin and, pushing it out, separate the amplifier pusher from the pedal. Having unscrewed the damaged amplifier from the pedal assembly, a new one is placed in its place. Moreover, it is necessary to ensure that its location is correct: the pedal should be at the bottom and the hose fitting at the top. After this, all previously performed operations are performed in the order opposite to removal.

Master brake cylinder

Now let's talk about the master brake cylinder on a VAZ 2110 car. If you do not want to allow the brakes to fail while driving, they should be checked periodically, and if problems arise, take appropriate action immediately.

A common reason for replacing the master brake cylinder of a VAZ 2110 is precisely the fact that the brakes are lost.

Symptoms of a problem

Of course, brakes can completely lose their effectiveness for various reasons, but now we are talking specifically about the master cylinder. If the reason lies therein, then it can be determined by the following signs:

• The master cylinder shows signs of brake fluid leakage;
• The pedal has an idle motion, that is, when it is pressed, no force is created;
• The brake pedal simply won't press.

To repair the master brake cylinder of a VAZ 2110, you will need to first disassemble it and then install a new element.

The most difficult process is disassembly. Therefore, let's talk about it in more detail.

1. Carefully disconnect the master cylinder from the pipeline.
2. Disconnect the block, which is equipped with wiring, from the emergency brake fluid indicator. The connection to the “ten” is made by terminals.
3. Cover the pipe and assembly openings with something to prevent brake fluid from leaking. It will pollute the interior space, which is undesirable.
4. Now remove the cylinder along with the reservoir. To do this, simply unscrew the fastening nuts that connect the element to the vacuum booster.
5. After removing the brake fluid level sensor, drain the brake fluid present from the cylinder and the cylinder itself.
6. If there is no serious need, you should not remove the tank. But for complete assembly, the tank is removed and then installed in place in strict order.
7. Before reassembly, each element is washed with purified brake fluid. A good alternative is isopropyl alcohol.
8. Do not forget to dry the parts with a compressor and wipe with a clean, dry cloth.
9. Carefully avoid contact of the main cylinder with fuel or kerosene.
10. Pay special attention to the O-rings. If you wash them with special alcohol, do not keep the rings in this liquid for more than 20 seconds. After processing, immediately dry and wipe the seals.
11. Treat the surface of the piston and mirror to remove all rust.
12. When replacing the master cylinder, new O-rings must be installed, regardless of their current condition.
13. Check the elasticity of the piston springs under load. Refer to the VAZ 2110 repair manual, which indicates the appropriate loads and forces for testing.
14. When free, the length of the spring should be 59.8 millimeters. If the indicator deviates from the norm, be sure to replace the springs.

If you think that after replacing the brake master cylinder you can safely go out on the roads, then you are mistaken. In fact, a complete repair of brake cylinders on a VAZ 2110 includes bleeding.

Proper bleeding will ensure the efficiency of the newly installed master cylinder.

The procedure is not complicated, but requires following the instructions.

• Find someone who will help you in this matter. One will be near the car, and the second will be directly in the cabin.
• Inflate the brake pedal by pressing it several times.
• The assistant presses the pedal, and meanwhile you slightly unscrew the fitting on one of the brake system pipes.
• This should release air, as well as a small amount of brake fluid. Don't be alarmed by leaks, this is completely normal.
• Retighten the fitting using the same wrench as when unscrewing - 10.
• Command your assistant to lower the part.
• The procedure is repeated until air bubbles begin to come out when unscrewing the fitting.
• Each of the four circuits is pumped using similar actions.
• First make sure that the brake fluid in the expansion tank is filled to the required level.

How to replace the vacuum brake booster on a VAZ 2110-VAZ 2112?

Removal: 1) First, unscrew all the screws that secure the soundproofing material (Most of the nuts are indicated by red arrows), then unfasten the belt securing the expansion tank of the cooling system (the tank is indicated by a blue arrow) and slightly lifting it up, remove it from the place where it is located.

We recommend: How to remove the window regulator on a Priora

The hoses are connected to it, do not disconnect them under any circumstances, otherwise liquid will flow out, which will stain your car. Of course, you can put some kind of container and drain all the liquid from the expansion tank, but why do this if you can do without it and the work will go much faster, then carefully place the tank somewhere and fix it and then take out the left (look in the direction of the car) part of the soundproofing material and put it aside.

Note! The same thing will need to be done with the right side, in order to remove it, you first need to move the rear window washer reservoir to the side (On VAZ 2110 cars, this reservoir is not present, it is only present on the VAZ 2111 and VAZ 2112), to do this, disconnect the two wires that fit it (see photo 3), unfasten the belt that holds it (see photo 4) and carefully remove it

If there is a lot of liquid in the tank, then you don’t have to remove it, just carefully place it on the fender, but if there is none or you have pumped it all out, then disconnect all the tubes remaining from the tank and after that, remove it completely from the car and finally remove the right parts of the noise-insulating material, with a 10 mm socket wrench, unscrew the two nuts (see photo 1) and with a thin flat screwdriver, pry up the brake booster hose holder (see photo 2) and disconnect it too, and that’s it, you can take out the sound-proofing material material so that it does not interfere with the removal of the brake booster from the vehicle!

2) Now that the soundproofing material is removed, disconnect the wiring block from the brake reservoir cap (Indicated by a red arrow), then disconnect the hose from the check valve of the vacuum brake booster (Hose indicated by a green arrow) and unscrew the two nuts (Indicated by blue arrows) securing the Brake Master Cylinder to the brake booster, then carefully move the GTZ to the side, but just be careful, make sure that the brake pipes do not burst, otherwise you will have to change them.

3) After the operation has been completed, move to the salon and there unscrew the four nuts that secure the vacuum booster bracket to the body (Indicated by red arrows), and also disconnect the wire blocks (Indicated by blue arrows) from the brake light switch (Indicated by green arrow), when everything is done done, you can move again to the engine compartment of the car and, once there, pull out the vacuum booster assembly with the bracket.

4) Having placed the vacuum seal on the ground or secured it in a vice, first of all, pull out the metal stopper with small pliers (Indicated by the red arrow), then carefully knock out the rod (see small photo, it is metal and comes out very easily), pressing on it from above or vice versa from below .

5) And finally, unscrew both nuts that secure the vacuum seal to the bracket and remove it, this completes the operation of removing the brake booster.

Installation: Install a new brake booster in the reverse order of removal, during installation, do not make a mistake and do everything exactly the same as before, when it is installed, do not wear soundproofing material, but try how it works (How to check the brake booster, we have already wrote above), if everything is fine, complete the installation of all parts as they were previously.