Replacement of Lada Granta door handles

Often, after time has elapsed on a Lada Granta car, the doors begin to open and close with some effort. To fix the problem in question with this car produced by AvtoVAZ, you have to contact a service station. In this case, you need to purchase door closers and door stops for Lada Granta.

Sometimes the owners of the Lada Granta Liftback, produced by the famous AvtoVAZ company, have to deal with various modifications after purchasing the vehicle. This happens for the reason that after even a short mileage, minor breakdowns or problems often appear at first, and if they are not eliminated in time, they develop into more serious ones. Many owners consider the most common defect to be the fact that the front door locks do not function well and open with great difficulty.

You can, of course, buy Lada door closers and door stops and make repairs in accordance with the instructions. But this operation can be performed in a more productive way. To carry it out you need:

A common symptom of a broken lock is that a loud sound appears before the door opens/closes. The design of the front door lock is made in such a way that the metal can sometimes rattle. In order to eliminate this problem, you need to remove the lock itself and put rubber tubes of the required size on the levers. Immediately all sounds coming from ahead will disappear. When closing the doors, only a bang will be heard, and all sharp and loud sounds will be a thing of the past.

If jamming and play are observed, they should be eliminated. Moreover, all this must be done at once. You can also buy limiters for the trunk lock. Before purchasing Lada door closers or door stops, you should first consult with a specialist. Having received the necessary and important information, you can choose the highest quality limiters. Problems with the operation of the lock can be solved by making a quality adjustment. To do this, certain actions must be taken.

Most often, the reason for poor lock performance is the difference in the radius of curvature of the upper door frame. If you look at it in detail, you can see that when simultaneously adjusting the locks at the rear of the car, they always touch the top of the sealing rubber differently. Tight opening compresses it much more in the closed position. To adjust the locks, you can use the following method.

Adjustment process

If the gap is smaller, lower the glass all the way down. Then close it with one click, take it by the top edge and push it towards you a couple of times with a little effort. And if the gap on the front door turns out to be wider, then you need to open it with the window down and, resting your foot on the trim, pull the door to the inside several times. Then it will be possible to move on to the main problem associated with the poor functioning of the lock.

• special screwdriver;
• Silicone Grease;
• limiters.

When there is a slight bulging outward, you need to put a soft and durable gasket in the opening and on the central post, in the place where the hinges are, and then try to close the door. If the door is slightly recessed relative to the body itself, then you need to support the outside with your knee in the hinge area and pull the open door towards you. By making such adjustments to the rear doors, you can achieve soft operation without various side effects.

You can install them either on the opening or on the door itself. Due to the presence of springs, closing/opening will be smooth and the sound will not be too loud. Basically, those who are faced with a similar problem most often try to solve it with the help of lubricant. In a way it helps, but only for a short time. And it can only get worse in the future.

Lada Granta sold › Logbook › #25 Installing door handles in the color of Granta Kalina 2

Hello friends, subscribers and those who just happened to be there)!

Your frequently asked questions will be as follows

1)

How much does revenge cost?
— 1000+300 delivery (Krasnodar-Samara) 2)
Will you choose the color?
— Yes, the shade differs little 3)
Where did you get it?
website Avtostolitsa63 4)
How is the quality?
Edges with chipped paint (Not critical). They could have made bigger holes for the gaskets 5)
Is it difficult to install?
No, it’s rather difficult to transfer the mechanism from the old handle. you will see in the description 5)
How long did the installation take?
5 hours leisurely 6)
Any nuances?
There are rods to avoid the effect on the handles that it is slightly open, I will describe it in the description 7)
Do you need any special tool?
No
Photo of the unpacking as they arrived

How to remove handles, watch this video, but since in that video the handles are not from Tune Auto, but the real original, which is not available for sale, I will show the nuances on the handles from Tune Auto, but the disassembly itself is no different

The first nuances when you have a pen on the table. It may seem to you that they need to be unpinned, but this is not necessary.

It will be difficult to install the mechanism on a new handle in the same place. On my driver’s door, this hook didn’t fit at all, I had to take a file and sharpen it (as you work, you’ll understand what exactly you need to file)

As for the front passenger door and the lack of a hole in it for the lock cylinder, here is the solution below

You can deal with the larva as follows: insert a spare key and put it aside

As for the rods, there is nothing complicated, but if you have the effect of a large gap in the handle, which makes it visually open, you need to experiment with the rod latch at what level of the rod to latch it, you will see in the pictures

1)

This is the most ideal option when the door opens with a light touch of the little finger, like in a Rolls Royce, but you need to test it, maybe it will open on bumps)
2)
It was like that at the factory with factory handles
3)
It’s better not to do that. The picture shows these 3 options and the thrust from front doors, it is the rod that comes with notches at the end, there are just 2 of them on the handle, a rod when closing with a key and just an opening rod on one handle, well, on the right door you will remove the key rod as unnecessary

1)

Don’t be afraid to unscrew the door lock, the adjustment will not get lost, the adjustment is made by the mating part of the lock, which is located on the counter, and you don’t need to touch it
2)
Push the rods not from the mechanism onto the handles, but from the lock, it’s easier to latch them back there
3)
Place the handle first, then return the lock, screw it on and then just fasten the rods to the lock
4)
For the front doors, if you have one, you can prepare a larger extension cord with an 8 head; you will unscrew the handle with the bolt located inside the door, you can also use a regular open-end key, so this is just a convenience
5)
Don’t forget during work to try to close the door and didn’t collect the door card, put it on and realized that the door won’t close and let’s take it apart again
6)
Who has grants older than 2014 in the video which is indicated in the description as a disassembly guide, there is information on how you need to redo the mechanism with the rear doors, My car was 15 years old and I didn’t have to do this.
7)
As I haven’t read about replacing handles, it’s very difficult to write everywhere, all the guys change well, especially since I sketched out some nuances for you and will quickly answer your questions in the comments.

Perhaps somewhere your paint may have chipped or rubbed off from an old pen, buy a bottle of tinting paint with a brush for 100 rubles at an auto store so you don’t have to run around later. 9) There is no need to remove the lock cylinder from the driver's handle! Only from the passenger side and get it WITH THE KEY INSERTED

Sequence of actions when replacing the front door handle on a Lada Grant

1. We place the car within the perimeter of the repair area and provide priority safety measures.
2. Open the front driver's door and raise the window to the top position.

1. Unscrew the three screws that secure the upholstery at the bottom.

1. We carry out dismantling on the right side by analogy.

1. We unscrew the little soldier - the door lock lever.

1. Use a screwdriver to pry off the plastic plug.

1. Additionally, we unscrew the screw that secures the upholstery in the middle part of the door card.

1. We unscrew the screws in the armrest niche.

1. Unscrew the handle fastening (two self-tapping screws).
2. We insert a flat-head screwdriver between the metal body and the plastic upholstery.
3. Squeeze out the plastic.
4. We remove the card from the seat.

1. Disconnect the block with wires from the locking lever.

1. By analogy, we disconnect the contacts from the electric window drive.

1. We remove the upholstery.

1. Use a screwdriver to pry up the power window control unit and remove the switches.

Replacement of Lada Granta door handles

Door handles on modern Lada cars are quite reliable. However, there are cases when, in severe frost or when excessive force is used, the handle mechanism breaks and fails. In this case, it needs to be replaced. The reason for the replacement may also be the desire of the car owner to switch to the handles from the Luxury package, which are painted in the color of the body and are more pleasant to use. Regardless of your motivation, the work will be almost identical.

Before starting the work process, prepare the following tools: an “8” socket or an open-end wrench of a similar size, an extension, a ratchet, a Phillips and slotted screwdriver, plastic spatulas for working with interior plastic, penetrating lubricant in aerosols. Before starting work, disconnect the negative terminal from the battery to avoid a short circuit.

To replace the outer handle of the Lada Granta door opening, we will need to remove the door card to gain access to the inner nut securing the handle. On the front doors, unscrew the screws in the indicated places with a Phillips screwdriver, unscrew the plastic cover of the door lock button and, using a plastic spatula, unclip the door card from the body element. On the rear door, the fastening screws are located under the plastic cover of the door handle; by snapping it off we will gain access to them.

We advise you to use specialized spatulas for working with plastic; such a tool will avoid damage to the plastic and worsen the appearance of the car interior.

After the door card is released, disconnect the power wiring for the power window buttons, if your vehicle has them.

To remove the external rear door opening handles, you will need to use a socket with an “8” extension or an open-end wrench of a similar size to unscrew the two attachment points of the external door opening handle. One nut is on the inside of the door, the second bolt is on the outside.

Further actions will depend on the year of manufacture of the car. If you have a Lada Granta Liftback, or a Lada Granta Sedan / Lada Kalina released later than the fall of 2014, then in your case a rod is used in the rear door opening drive. You will need to additionally release the metal rod retainer from the door lock. If you have a car manufactured earlier than the fall of 2014, then no additional actions will be required.

After releasing the fastening points, we move the handle in the direction of travel of the car and, simulating the opening of the outer door handle, rocking it, remove it from its seat.

Considering that since 2014 AvtoVAZ has changed the type of rear door lock drive from the external opening handle, it is possible that the mechanism on the handle does not correspond to the lock mechanism. If this happens in your case, you will need to move the door lock drive from the old handle to the new one. To do this, you will need to loosen the tension of the return spring and knock out the pin holding the drive. Use a slotted screwdriver to pry up the edge of the return spring and remove it from the seat.

Having placed the chisel on the base of the pin, lightly knock out the retaining pin with light blows of a hammer.

We repeat the same procedure with the donor handle and install the old mechanism on the new door handle, returning the pin to its place and restoring the tension of the return spring.

Reinstall the outside rear door handle in the reverse order of removal. We also recommend lubricating all working mechanisms of the door handle with penetrating lubricant to facilitate their operation.

Let's also consider the process of removing and replacing the front outside door handle , as well as the process of replacing the door lock cylinder .

Similarly to the rear door, unscrew the inner nut securing the door handle, as well as the bolt of the outer fastening point. Unlike the rear door, the window lifter frame will interfere with unscrewing the inner fastening nut in the front door. To avoid the process of dismantling the glass lifting mechanism, use a cardan for the extension.

Then you will need to disconnect the door lock drive rods coming from the outer handle and the lock cylinder. By squeezing the plastic and metal clamps of the rods, we disengage them.

Thanks for subscribing!

Then, simulating the opening of the door handle and swinging it from side to side, we remove it from its seat in the same way as the back door. If it is necessary to replace the lock cylinder or move it to a new handle, using a thin metal object, press the locking tab of the door lock cylinder and take it out.

Attention! Before starting the process of replacing the door lock cylinder, be sure to insert a working key into it, otherwise, when you remove the cylinder, its pins will scatter in different directions under the influence of the springs and it will not be possible to put it back into working order.

To install a working door lock cylinder, simply snap it in the reverse order of removal. Do not forget to take into account the fact that the tide on the outer part of the body must “look” towards the trunk of the car, otherwise the door lock mechanism will be upside down and will not work correctly.

Not forgetting to move the door lock rods from the old handle to the new one, install everything in the reverse order and enjoy the work of the new outside handle.

Let's proceed to the second stage: dismantling the side view mirror

1. Using a screwdriver, unscrew the three screws that secure the mirror frame to the body.

1. Using pliers, remove the locking bracket.

1. We remove the mirror and remove the hinges through the diagnostic hole.

1. Using an “8” socket, unscrew the bolt that secures the outer handle to the end of the door.
2. In the inner tunnel, unscrew the second bolt holding the handle.
3. Using a screwdriver, carefully pry up and remove the rods from the lock.
4. We remove the handle from its seat, turning it slightly from side to side.

Front door lock device of Lada Granta

In conclusion, we carry out troubleshooting, inspect adjacent parts and mechanisms, and replace them with new ones as necessary. Replacing the front door handle on the Lada Grant is completed.

Review of spare parts prices

*prices are current as of November 27, 2018.

Recommendations for choosing and replacing door handles

When choosing spare parts, always give preference to original ones. Good, high-quality parts are always 10 - 15% more expensive than analogues. At the same time, by purchasing a factory part, you can count on a long service life of the mechanism.

A cheap counterfeit does not provide even a third of the required resource. The final choice is up to the owner of the technical device. The deciding factor is the budget.

Repair kit

Repair kits for the Lada Granta car have the following articles and prices:

• rear right DAAZ – 1118-6205150, price – 450 rubles.
• rear left DAAZ - 1118-6205151, price - 450 rubles.
• front left DAAZ – 1118-6105151, price – 505 rub.
• front right DAAZ - 1118-6105150, price - 505 rub.

• rear left LADA – 2190-6205181, price – 145 rubles.
• rear right LADA – 2190-6205180, price – 145 rubles.

In addition to original repair kits, you can use spare parts from similar models of the VAZ line, caps, levers, fasteners, clamps, rods, lock cylinders.

source

Adjusting the front left (right) door lock on the Lada Granta

In the process of systematic use of the door, its frequent opening and closing, the lock and adjacent elements wear out. As a result, the door closes with a distinct knocking sound.

Often knocking occurs after an accident due to changes in body geometry. The functionality of the lock can be restored by partially repairing it, and in case of deformation, by completely replacing it with a new one.

• screwdrivers, set of auto tools;
• lubricant;
• liquid WD-40.

Sequencing

1. We inspect the gaps around the entire perimeter of the door. We mark areas with deviations. The factory standard is 2–3 mm, anything higher or lower is a defect.
2. Using a screwdriver, unscrew the screws securing the hinge to the body. If necessary, use an impact screwdriver.
3. Move the hinge a few millimeters up and down and check the tight fit of the door to the body. If you hear a rumble when closing, lower the hinge; if you hear a dull knock, raise it.
4. We carry out a control measurement and tighten the bolts.

By analogy, we adjust the lock on the opposite side.

Reviews

Conclusion If the need arises, you can replace the door handle on the Lada Grant yourself. The process is not complicated, and the principle of operation is intuitive.

When selecting and purchasing consumables, give preference to parts with factory catalog numbers. When contacting a service station, request a quality guarantee for the work performed.