Length of VAZ 2110 - body and overall dimensions

The graphs show the dimensions of the VAZ 2110 car - width, length and height. Data is shown for all available modifications, including, for some, the overall width with mirrors.

The smallest cars are marked in green, and the largest in red.

Below is a summary table of overall dimensions for all modifications of the VAZ 2110.

Overall dimensions of VAZ-2110 cars, 2111, 2112

VAZ-2110 is a front-wheel drive passenger car with a transverse power unit, designed for use on paved roads.

The body is all-metal, monocoque, four-door, sedan type. To transport large and long cargo, the rear seat can be folded, thereby increasing the trunk volume.

Engines are four-cylinder, carburetor or with various fuel injection systems, with a displacement of 1.5 liters. Thanks to the front-wheel drive layout, the car has improved handling characteristics compared to rear-wheel drive VAZ models, especially on slippery roads and when cornering.

It is possible to equip the car with fog lights, heated front seats, electric windows, an on-board computer, a catalytic converter in the exhaust system, electric exterior mirrors, an electronic anti-theft system, air conditioning, anti-lock brakes, an airbag, and a sunroof.

The VAZ 2110 car was produced from 1995 to 2007. This sedan was created on the basis of the Lada 2108 hatchback. The dimensions of the VAZ 2110 differ slightly from the overall dimensions of the 21099 model. In particular, the length of the VAZ 2110 is only 6 cm longer than the length of the only sedan from the Lada Samara model range.

The length of the wheelbase is 3.2 cm longer, the height of the car is 1.8 cm, and the ground clearance of the loaded “ten” is 5 cm higher than that of the ninety-ninth. The front and rear wheel tracks of these sedans are the same. The same engines and gearboxes were installed on both cars.

Length

The geometry of the VAZ 2110 body is described in the operating instructions. The main parameters for checking body geometry are as follows:

1. There should be 4.265 meters between the extreme points of the front bumper and the rear bumper.
2. The distance between the center of the front wheel and the center of the corresponding rear wheel is 2.492 meters.
3. The distance from the center of the front wheel to the end point of the front bumper is 0.829 meters.
4. The distance from the center of the rear wheel to the end point of the rear bumper should be 0.944 meters.

The height of the car is always stationary - 1420 mm

You should try to avoid welding and other work that involves thermal heating of the metal.

Subtleties of body repair

Body repairs are most often carried out after an accident, but also if some parts are rusty. But you should still try to avoid welding and other work that involves thermal heating of the metal.

Small scratches and chips can become a source of corrosion in the future. In order to avoid this, it is best to tint small defects. Details: https://vazweb.ru/desyatka/obschee/kak-podkrasit-skolyi-na-mashine-samomu.html

If possible, try not to remove bezels. This can also lead to changes in body geometry. And after any repair work related to the body, be sure to check its linear dimensions.

A significant part of the repair work on cars, especially those arriving after road accidents, falls on body repairs. In most cases, when repairing a body, it is necessary to check the geometry of the attachment points of components and assemblies of the vehicle chassis. Geometry of the body and engine compartment of the VAZ 2110-12 in the diagrams:

If the body is heavily damaged, it is recommended that all interior trim be removed to facilitate measurement, inspection, and installation of hydraulic and screw jacks to correct distortion and damage to the body. Protrusion of the front surfaces and removable parts relative to adjacent panels is eliminated by fitting and adjusting them.

Specifications

Fiat albea, review, modifications, characteristics
Technical characteristics of the VAZ-2112-37

Curb and gross vehicle weight

We present to your attention a table that shows the weight of the car by brand.

Thus, it turns out that if we take, so to speak, “in general for the hospital,” then the average weight of a passenger car is approximately from 1 to 1.5 tons, and if we talk about SUVs, then the whole weight already shifts from 1.7 tons to 2. 5 tons.

The gasoline engine with a carburetor power supply system is located transversely at the front. Unit volume 1.5 l. with a power of 76 hp. and 5600 rpm, 4 in-line cylinders with 8 valves.

Later, the engine was modernized and 16 valves were built into it, like on most modern cars. The maximum speed of the engine is 165 km/h, and acceleration to 100 km/h is possible in 13.2 seconds.

Its fuel consumption is economical:

• in the city 8.9 l/100 km.
• on the highway 6.5 liters.
• in mixed mode 7.6 l.

In addition to the main engine option, the “tag” has various power variations of the 1.6 liter engine: 80/81/98 hp. With this unit installed, the car can accelerate to 160 km/h in 13.5 seconds. to "hundredth".

Consumption accordingly also increases to 10 liters in the city, 5.7 liters. outside the city and 7.6 l. average. The system of such an engine has been changed, and fuel injection is carried out multipoint. Even fuel costs more to use, namely AI 95. If you wish, you can choose a 1.3 liter engine and a 1.5 liter, but with 78 hp.

VAZ-2110 Tank volume, trunk Load capacity Fuel consumption

History of the Lada 2106 car and its modifications

Motorists, in front of whom VAZ was developing and putting into production the “ten”, exclaimed with one voice: “If only it had appeared 10 years earlier, it would have been a very interesting car!” The VAZ-2110 car, indeed, could create the image of a modern, by world standards, manufacturer for the plant. The first samples of the car appeared in 1989, they looked fresh and modern, and the technical solutions did not lag behind those used in the models of leading European manufacturers. Important innovations were fuel injection and an on-board computer, which were being introduced around the world on low-cost cars at that time.

Load capacity and weight of KAMAZ dump trucks

KAMAZ dump trucks are the largest group of trucks, numbering about forty models and modifications. This series includes both dump trucks in the usual sense of the term and cars with opening sides.

In addition to differences in technical characteristics, cars differ in the degree of comfort.

Technical features of LADA 2110

Audi rs6 model description characteristics modifications photo video

Compared to the VAZ -21099 model, the performance characteristics of the “ten” were significantly improved. So fuel consumption with a 1.5-liter engine became 7.5/100 km, which is 12% less than the previous model, and the maximum speed was also increased to 162 km/h.

The model with an 8-valve 79-horsepower, 1.5-liter engine already developed 170 km/h and went to “hundreds” in 14 seconds. The engine fit perfectly into heavy city traffic due to its torque and elasticity.

The engine version with a twin-shaft 16-valve head, 1.5 liter capacity, produced 94 hp. and provided acceleration to “hundreds” - 12.5 s and a maximum speed of 185 km/h.

Pros and cons of the car

If you choose a car for everyday use and you need to know all the pros and cons of this car, I recommend that you familiarize yourself with all the pros and cons of this car.

Pros of the VAZ 2110

• Available service;
• Availability of spare parts;
• Possibility of repairs “in the garage”;
• Front-wheel drive;
• 16-valve injection engine;
• Improved security system;
• Low fuel consumption;
• Suspension adapted to poor-quality road surfaces;
• There is a hydraulic power steering wheel;
• The steering column can be adjusted;
• Air conditioning can be installed;
• Improved front panel.

Cons of the VAZ 2110

• Corrosion of metal;
• Small resource of some spare parts;
• Build quality;
• Unbalanced operation of the stove;
• Low sound insulation of the cabin;
• Constant monitoring of the timing belt;
• Equipment.
• There is little free space inside the car;
• It will be uncomfortable for three adult passengers to sit in the back.

How does wheel weight affect vehicle performance?

Let's start with the fact that all motorists know the fact of increased fuel consumption when transporting goods. In this case, the car becomes heavier, which means the engine needs to generate more energy to transmit torque to the drive axles. About the same thing happens if the car is equipped with heavy wheels. The weight of the car will increase, which will affect increased fuel consumption.

Many drivers have noticed that after switching to alloy wheels, the car becomes more maneuverable and economical. That's right, the weight of the unsprung mass has decreased, and this has led to a decrease in engine energy consumption.

Lighter wheels increase the service life of the suspension and steering. And this also affects the savings of your personal budget. The car accelerates faster and has a reduced braking distance. In addition, riding on light wheels improves the quality of comfort, since the sprung mass easily absorbs transmitted vibrations from the lightweight unsprung mass.

The weight of the assembled wheel may vary depending on the tire pressure. Although a flat tire contains air, at atmospheric pressure its mass is 20 grams (m=V*p=3.14*0.14^2*0.9*1.25/4=0.02kg). And the air density of an inflated tire is approximately 3 times greater. Therefore, the difference in mass is 20*3-20=40 grams.

Causes of breakdowns

There can be many reasons for malfunctions. The most common problem is that the lamps burn out, which naturally makes it impossible to turn on the side lights. Lamps brought to us from the Middle Kingdom are especially unreliable in this regard.

Although they are attractive at a more than “democratic” price, and there are plenty of them at any retail outlet, you won’t be able to get away with them. Therefore, perhaps we should remember the saying that we are not such rich people as to buy cheap things twice.

Good branded light bulbs will last many times longer, and you won’t have to change them endlessly.

Lamp options for dimensions

Sometimes there is a “flashing” of the dimensions, or the blinking of the instrument panel lighting when the side lights are turned on. Many blame the size relay for this, but they cannot find it. In the carburetor VAZ 2110 there is no size relay, there is only a relay for high and low beam.

For a fuel-injected car, the relay should be found in the mounting block, where all the fuses are located. Moreover, if the relays burn one after another, you should immediately contact electrical specialists, because this indicates that there is a short circuit somewhere in the circuit, and from here it is not far from the burnt-out car.

Mounting block and relays and fuses

Never, under any circumstances, should a blown fuse be replaced with a more powerful one, or even with a “bug”.

Body geometry of VAZ 2110 and 2112

VAZ 2110 cars that leave the factory assembly line have clearly verified body dimensions

However, few people pay attention to them when buying. As a rule, a driver begins to become interested in the dimensions of the body of his car in the following cases:

1. There are plans to buy a car of this brand second-hand, but the buyer wants to make sure that the vehicle has not been in an accident before. Body geometry will help answer this question.
2. The driver himself got into an accident. This could be a collision with another vehicle or a tree, curb, wall, etc. Body repair materials will be needed. In addition, the driver will need to select tools (for example, find out the dimensions of the slipway for body repair).

Factory dimensions

To accurately find out the dimensions of the body, it is enough to carefully study the vehicle’s operating instructions.

Length

The geometry of the VAZ 2110 body is described in the operating instructions. The main parameters for checking body geometry are as follows:

1. There should be 4.265 meters between the extreme points of the front bumper and the rear bumper.
2. The distance between the center of the front wheel and the center of the corresponding rear wheel is 2.492 meters.
3. The distance from the center of the front wheel to the end point of the front bumper is 0.829 meters.
4. The distance from the center of the rear wheel to the end point of the rear bumper should be 0.944 meters.

The height of the car is always stationary - 1420 mm

Width

1. The distance between the end points of the side mirrors is 1875 mm.
2. The distance between the front end points of the car (excluding side mirrors) is 1680 mm.
3. The distance from the center of the right front wheel to the center of the left is 1400 mm.
4. The distance from the center of the right rear wheel to the center of the left is 1370 mm.

When measuring the body geometry, remember that the body geometry of the VAZ 2112 differs in many places from the VAZ 2110.

Geometry check

Here are four main types of measurements that will allow you to make sure that the car has not been in an accident and has the parameters you need:

Reconciliation of diagonals. Before proceeding with detailed calculations, you should make two simple measurements that will immediately identify the problem. The car needs to be measured diagonally on both sides. If the measurement results coincide (with an accuracy of a millimeter), this will mean that the body as a whole has the correct shape. But we should not stop at these two dimensions. Checking the height of the racks. For this measurement you need to measure the height of the racks in four places

It is important to take measurements from the front and rear, as well as from both sides of the machine. The four indicators must match. Identification of a distorted roof plane

To find out if your car's lid is in place, take measurements from the door diagonals. You need to measure from the bottom rear corner of the door to the top front corner, and vice versa. If the indicators coincide on both sides, good. Just in case, it’s worth checking the roof diagonals.

1. Determining the correct location of the front glass. Contrary to popular belief, even if the windshield fits correctly, its geometry can be distorted. Therefore, be sure to compare the lengths of the diagonals of this part.

As a rule, problems with mismatched machine parameters arise after road accidents. However, this does not happen 100% of the time.

Welding or other repairs that involve heating the metal can affect the physical parameters of the vehicle. Therefore, each time take the above measurements after the car has been to the auto repair shop.

Body geometry and its diagnostics

ATTENTION! A completely simple way to reduce fuel consumption has been found! Don't believe me? An auto mechanic with 15 years of experience also didn’t believe it until he tried it. And now he saves 35,000 rubles a year on gasoline! Read more"

The most important components of body geometry are called control points. It is the knowledge of their location and the ability to correctly measure the distances between them that determines the structure of checking the body for deformation. You can learn more about control points from the technical documentation for each car model.

After identifying damage, the integrity of the body is usually restored in special workshops. Experienced straighteners bring the body back to normal in the shortest possible time, if only the deformations are of moderate or minor severity. A body that has been in a serious accident and has received a lot of deformation is usually easier to replace with a new one.

What deformations can occur on the VAZ 2110?

The “Ten” involved in the accident will have certain deviations from the standard positions marked at the factory. And destruction in this case means the following:

• Deviations in terms of the standard wheel arrangement, as evidenced by poor vehicle stability and increased tire wear;
• The diagonals, again, standardly installed at the factory, are violated. Doorways, pillars and other areas of the body, one way or another, associated with the impact zone are especially often affected.

In most cases, the destruction of functional elements is associated with the appearance of folds in the floor or other components of the body. In addition, external impacts cause a significant increase in the part in areas far from the point of impact.

Note. Such structurally weak areas include empty spaces between welds, side members and other elements where free mutual movement of metal sheets is observed.

Several ways to check the body for deformation

You can determine the deformation of a body that has been in a moderate accident at first glance. On the contrary, if the blow was weak, then it can be extremely difficult to determine the damage by eye. In this case, you have to carefully carry out diagnostics, measure compliance, and so on.

A hydraulic jack helps to carry out an initial inspection of the car. Thanks to the lift, you can examine the condition of the floor, feel those parts of the body that are inaccessible for inspection with the normal position of the car, for the presence of folds. After detecting the latter, as a rule, they are marked with a marker, which makes it possible to easily find deformed areas during subsequent stages of work.

If such a check does not give any results, proceed to the next stage of the examination, which involves checking the wheels. It is no longer a jack, but a special stand that helps carry out the check. Using such equipment, it is easy and faster to carry out the second stage of diagnostics. Check the front and rear wheels of the car at control points using calipers with a special profile shape.

Checking the compliance of the control points of the “shoes” of the car involves verification (comparing) the wheel coordinates located on one side of the car with the coordinates on the other side. Body deformation becomes obvious if measurements show significant deviations from specified standards.

Another method of diagnosing damage to the “tens” body is to compare the diagonals. The exact coordinates of the main diagonals are given in the table below. This diagnosis is considered the most correct, since it is carried out using a symmetry check.

Modern technologies make it possible to check body geometry using various tools. A computer on which appropriate measurements are carried out helps a lot in this matter. The option of checking using template tools and mechanical measurements is also used.

Factory dimensions

But the main dimensions are:

Length:

• if we take the end points of the front and rear bumpers, then here we have 4265 mm;
• length between the centers of the front and rear wheels, the so-called. wheelbase is 2492 mm;
• from the center of the front wheel to the extreme point of the front bumper - 829 mm;
• from the center of the rear wheel to the end point of the rear bumper - 944 mm.

The height of VAZ 2110 is 1420 mm.

Factory dimensions for length and width

Width:

• in front at the extreme points of the “factory” mirrors – 1875;
• front excluding mirrors (purely hardware) – 1680 mm;
• distance between the centers of the front wheels – 1400 mm;
• the rear of the car has a width between wheel centers of 1370 mm.

dimensions

As noted above, the 2110 sedan turned out to be wider, taller, longer and heavier than the cars of the base family. This happened thanks to the desire of the designers of the Volzhsky Automobile Plant to increase the space in the car interior and increase comfort for the driver and passengers.

Thanks to the increase in the wheelbase and the width of the body, the car has become much more spacious; the semi-recumbent driver's seat, so characteristic of the Lada Samara family, has become a thing of the past; there is more space for passengers sitting in the back. The 110 family became the mother family for the premium Priora model. Overall dimensions of VAZ 2110:

• body length (including bumpers) - 426.5 cm;
• wheelbase length - 249.2 cm;
• height when equipped - 142 cm;
• distance from the front axle to the end of the bumper - 829 mm;
• distance from the rear axle to the end of the bumper - 944 mm;
• body width - 168 cm;
• the distance between the tips of the side mirrors is 187.5 cm;
• front track - 140 cm;
• rear track - 137 cm;
• maximum ground clearance (empty car) - 18 cm;
• ground clearance (unloaded car and driver) - 17 cm;
• minimum ground clearance (driver, 4 passengers and luggage) - 16.5 cm.

It is worth noting that ground clearance is based on 13-inch wheels with 175/70 tires, or 14-inch wheels with 175/65 tires. When using other wheels or tires, the ground clearance will be different.

Hidden body cavities and their processing

The geometric dimensions of the VAZ 2110 body may be violated if the car has been in an accident. A car accident may involve the crash of two vehicles colliding together, a collision with an obstacle, or a wheel falling into a hole. From the article you will learn how to measure the geometry of a “ten” body, what methods allow you to give an accurate conclusion about deformations and damage, and much more.

Bodies and what they are like

As you know, the body on the “ten” is load-bearing and repeats the basic design of any modern passenger car. Today it is customary to talk about several types of bodywork. The frame and supporting body are considered the main ones.

The difference between frame and load-bearing

All the main components of the car are located on the frame; it serves as a support and is itself fixed to the wheels of the car by means of suspensions. If you pay attention to trucks, then the frame can be seen with the naked eye, and thus you can draw appropriate conclusions about its structure. In “passenger cars” there is no frame, or it would be more accurate to say that on some passenger cars the frame-body assortment forms a single whole, called the body.

Frameless bodies, which include the metal frame of the VAZ 2110, are made in such a way as to withstand the mass of numerous heavy components. For this purpose, the body floor is well reinforced, and most of the overall parts are made of materials with a lightweight base.

On frameless bodies, the role of the frame is performed by the spars. They can be said to be responsible for the massiveness of the entire body structure. From time to time, these components are subjected to unplanned and shock loads that change very quickly in different directions. This operating scenario cannot have a positive effect, and over time, the welding points break, the bolts become loose, and the solidity of the entire body structure weakens.

VAZ 2110 body diagram

The car body also feels the load from a running engine. It vibrates strongly, although the engine itself and the cylinders are designed to absorb some of the vibrations. To minimize the effects of vibrations on the body, manufacturers use special cushions or dampers, as well as washers made of dense rubber.

Note. The effect of these pads can be clearly determined by monitoring the operating unit with the hood open. The engine “growls” and shakes, but the body doesn’t care.

The most important task of a frameless car body is to transport luggage and passengers. At the same time, the machine must also provide major protection. The number of people transported and the weight of the permissible load are determined by the designers responsible for the layout and other parameters of the body.

If you imagine the frame of a “car” in the form of its components, then its main parts are three main zones, implying the trunk, the passenger compartment and the front. The finished look of the solidity of the frame is given by its hinged parts or “plumage”, which includes various panels.

Body types of the “tenth” family

The difference in body types, again, is associated with what one or another model is intended for. The car may be intended for off-road travel, and then it will be designed as a crossover or a full-fledged all-terrain vehicle, or it may be intended only for city driving.

Note. The body of the VAZ 2110 is a typical sedan. Models associated with the “ten” already have other body types: 2111 – station wagon, 2112 – 5-door hatchback, 21123 – coupe or 3-door hatchback.

It will be useful to know that over the entire production period of the 2110 model, VAZ creates many variations of this sedan. In particular, the Consul limousine, with an even longer wheelbase, deserves attention.

Related models based on family

LADA 1106

VAZ-21106 late modification

A joint project of the AvtoVAZ company and, created on the basis of the VAZ-2110 car for its homologation in the WRC group.

The concept car exhibited at the MIMS-96 exhibition was called “Yellow Shark”. The concept car was equipped with original yellow Slik wheels.

The Mega-Lada Motor-Sport engine is based on the “eighty-third” block. Later it was replaced by the Opel C20XE 16V with 150 hp. With. Engines, gearboxes and other equipment were supplied by the sports department of the English branch of General Motors - Vauxhall. Cars of the “budget” configuration were distinguished by the Opel Ecotec X20XEV engine with a power of 136 hp. With.

Initially, the car was equipped with Lockheed brakes.

The body of the VAZ-21106 differs from the VAZ-2110 in the rear and front fenders with extended wheel arches. An external plastic body kit was installed on this car. Subsequently, at the request of customers, this body kit began to be installed on regular “tens”, the kit was called “Nola”.

In 1998, the design of the car was changed due to the popularity of the model among the special services. In 1999, the car's design was changed to a more practical one. The shape of the bumpers was changed, and the plastic trim on the doors and hood was removed. According to the manufacturer, this reduced the noise level inside the car when driving at speeds above 200 km/h. Some cars had a minimal body kit similar to the 21106 "C" and sometimes had two oval air intakes on the hood.

In 2003, the plastic body kit was replaced with a completely different shape. There were also releases with a complete lack of body kit, with the exception of extended wheel arches.

was installing an air conditioning system in the cabin. A hydraulic booster from the German company ZF was installed in a car of any configuration.

A version of the VAZ-21106 with a coupe body was produced.

The car received a prize from the magazine “Behind the Wheel” - “For the best exhibits of MIMS-96.”

Modifications

• VAZ 21107 is a modification for rally competitions. Welded safety cage, different suspension design. Pre-manufactured at the VAZ Scientific and Technical Center, they were tested and refined. Testing on English rally tracks was carried out by Alistair McRae.
• VAZ 21127 is a modification with a VAZ-2112 body. Increased engine power.
• VAZ-21106 “C” Coupe - modification with a coupe body, Opel C20SEL engine with a power of 136 hp. With.
• VAZ 21106 WTCC - participated in the 2008 FIA WTCC international championship, used by the Russian Bears Motorsport team. B was used by the Lada Sport team.

LADA Tarzan 2

VAZ-2111-90 Tarzan-2

A family of passenger cars produced by AvtoVAZ. The family consists of VAZ-211290 and VAZ-211190.

In 1999, the Lada-Consul enterprise, together with the design organization DECON and the STC OPP AVTOVAZ, created an SUV called Tarzan 2. This car had a body from the family of the front-wheel drive VAZ model (VAZ-2112) and a frame with the main units from the Niva car installed on it (suspensions, gearbox, transfer case, steering). The units, except for the cardan shafts (the length was changed), springs, shock absorbers and frames, were used from mass-produced VAZ cars. The body is mounted on the frame via rubber pads. The rear suspension was borrowed from the Niva, which also entailed the transfer of the gearbox and drive shafts. The rear brakes are similar to the front ones, that is, disc brakes, 15-inch wheels. Despite the 150 kg increase in weight relative to the Niva, the fuel consumption of the new all-terrain vehicle, thanks to good aerodynamics, turned out to be noticeably less.

There were also changes in the design: the joints of the frame and body were closed with powerful pipes in the form of sills, linings on the wheel arches, which gave a new shape to the wings and the size of the arch, and linings made of pipes under the front and rear bumpers. In the cabin, the lining of the central tunnel has changed: the lining from the VAZ-21213 was used, and there were three levers on it (the gearbox and two more to control the transfer case).

The cars were made to order; the total number of Tarzans produced did not exceed several hundred.

Stories from our readers

“Fucking basin. "

Hi all! My name is Mikhail, now I’ll tell you a story about how I managed to exchange my two-wheeler for a 2010 Camry. It all started with the fact that I began to be wildly irritated by the breakdowns of the two-wheeler, it seemed like nothing serious was broken, but damn it, there were so many little things that really started to irritate me. This is where the idea arose that it was time to change the car to a foreign car. The choice fell on the melting Camry of the tenth years.

Yes, I had matured morally, but financially I just couldn’t handle it. I’ll say right away that I am against loans and taking a car, especially not a new one, on credit is unreasonable. My salary is 24k a month, so collecting 600-700 thousand is almost impossible for me. I started looking for different ways to make money on the Internet. You can’t imagine how many scams there are, what I haven’t tried: sports betting, network marketing, and even the volcano casino, where I successfully lost about 10 thousand ((The only direction in which it seemed to me that I could make money was currency trading on the stock exchange, they call it Forex. But when I started delving into it, I realized that it was very difficult for me. I continued to dig further and came across binary options. The essence is the same as in Forex, but it’s much easier to understand. I started reading forums, studying trading strategies. I tried it on a demo account, then opened a real account. To be honest, I didn’t manage to start earning money right away, until I understood all the mechanics of options, I lost about 3,000 rubles, but as it turned out, it was a precious experience. Now I earn 5-7 thousand rubles a day. I managed to get the car buy after half a year, but in my opinion this is a good result, and it’s not about the car, my life has changed, I naturally quit my job, I have more free time for myself and my family. You’ll laugh, but I work directly on the phone)) If If you want to change your life like me, then here’s what I advise you to do right now: 1. Register on the site 2. Practice on a Demo account (it’s free). 3. As soon as you get something on the Demo account, top up your REAL ACCOUNT and go to REAL MONEY! I also advise you to download the application to your phone, it’s much more convenient to work from your phone. Download here.

Read more: The coolest car in the world 2018

Deformed areas of panels are straightened, as a rule, manually using special tools (metal, plastic, wooden hammers and various mandrels) and devices. Straightening with heating is used for upsetting (pulling) highly stretched surfaces of panels. To prevent sudden swelling and deterioration of mechanical properties, the panels are heated to 600-650°C (cherry-red color). The diameter of the heated spot should be no more than 20-30 mm.

Additionally, you can download the electronic document in PDF format “LADA CAR BODIES, technical requirements for acceptance for repair, repair and release from repair by enterprises of the service and sales network of JSC AvtoVAZ” (Password for the archive: lada2111.ru).

In this guide you can find:

• Dimensions of openings and clearances of mating body parts of VAZ 2110, 2111, 2112 and 21123
• Engine and suspension mounting points on VAZ 2110, 2111, 2112 bodies
• Requirements for the painted surface of a repaired body
• Classification of body distortions
• and much more

By the way, the geometry of the VAZ 2110 and Priora bodies is the same. After restoring the geometry of the body, it must be painted. Read how to do it yourself.

Have you ever used the geometric dimensions of a VAZ body?

The geometric dimensions of the VAZ 2110 body may be violated if the car has been in an accident. A car accident may involve the crash of two vehicles colliding together, a collision with an obstacle, or a wheel falling into a hole. From the article you will learn how to measure the geometry of a “ten” body, what methods allow you to give an accurate conclusion about deformations and damage, and much more.

see also

Comments 18

I also need sizes to check, so which ones to use!

I made it approximately according to my measurements

You probably haven’t been here for a long time) I’ve already done and sold the car! I won’t edit the blog anyway!

Yes, I already made mine too. But this recording will still be useful to someone

Wow, I should try to measure it)

Didn't take any measurements? Otherwise, in just a week I’ll go on vacation, and I’ll start doing shamanism a little

Not yet, I won’t get around to it, but I’ll definitely write back if I intend to)

I would be very grateful

Vitaly Kakhovka on YouTube did the 10th family in the video everything is there

Thank you. Let's take a look too

A1=119.5 A2=119.5 B=127 B1=46 B2=46 D1=49.5 D2=49.5 D=96))) my TV is further welded

Thanks Slav. We will still wait for at least a couple of measurements to choose the “golden mean”, so to speak.

Thank you for your quick help in measurements pandaaaaaaaaaaa And so here are his measurements: A1=118.5 A2=118.5 B=127 B1=44 C2=44 D1=48.5 D2=48.5 D=95.5 Thanks to him It seems that the dots are not seriously gone, ± 0.5 cm

Thanks for the sizes, I couldn't find them anywhere. According to these dimensions, they are one to one ±5 mm (as they measured with a tape measure) But between the glasses (shock absorber rod), according to the book there should be 1103 mm, but for me it is 1003 mm. I don’t understand how this happens((

I won't even give you a hint.

Thank you for your quick help in measurements pandaaaaaaaaaaa And so here are his measurements: A1=118.5 A2=118.5 B=127 B1=44 C2=44 D1=48.5 D2=48.5 D=95.5 Thanks to him It seems that the dots are not seriously gone, ± 0.5 cm

Is this the exact size?

Depends on what. You can choose a middle ground. There is generally little information about the VAZ-2110

I'll write first. My sizes may differ radically from yours, since I measured the points as I currently have them. And so: A: I couldn’t measure it because of the installed 3 liter receiver. B: 126.5 cm. B: left - 45 cm, right - 45 cm. (right and left, as look at the picture) D: L - 48 cm, R - 48.5 cm. D: 95.5 see. Feel free to write measurements, I really need them. It took me a maximum of 1 minute of my time. Thanks everyone for your help

Cars coming off the assembly line have strictly verified body dimensions. As a rule, no one pays much attention to this when buying a new car.

However, the need to measure and check the geometric dimensions of the VAZ 2110 body with the instruction manual may arise in the following cases:

• you buy a car second-hand and are not sure that it has not been in an accident. It is because of this that, as a rule, the geometry of the VAZ 2110 is most often violated;
• you yourself got into an accident, even ran into a stone, curb, etc., causing the car to receive a serious blow.

Characteristics of the Bogdan VAZ 2110

• However, in terms of dimensions, everything is no different from the usual ten. The length of the car is 4265 mm. The width of the car is 1680 mm. Height 1420 mm. Tank capacity is 43 liters. The mass of the car in kilograms is 1030.
• Ground clearance of 170 millimeters, you can get stuck even in an ordinary puddle. Acceleration to hundreds, stated
• The manufacturer doesn’t set it to 12 seconds, but 30-40 seconds will be checked at the point; in principle, you won’t be able to accelerate very much on our roads. On a full tank it can travel almost six hundred kilometers.
• Five-speed manual transmission. It has its own errors, the third speed may go out.
• The steering wheel is covered with eco-leather, adjustable only in height, there is no adjustment for reach. Not very comfortable for a tall person.
• 5-seater sedan, equipped with a trunk with a volume of 450 liters. Quite roomy, even a baby stroller will fit in its cathedral form.
• The trunk is opened from inside the car.
• Installed 14 tires 185*65, wheels made in China. Although now almost everything is Chinese, so it’s not surprising.
• Front brakes are disc, rear drum.
• The adjustment of seats and mirrors is completely mechanical. The fuse box is accessible and fuses are easy to change.

Ground clearance of VAZ 2110, increase in ground clearance of Lada 2110

The ground clearance of the VAZ 2110 or ground clearance , as for any other passenger car, is an important factor on our roads. It is the condition of the road surface or its complete absence that makes Russian motorists interested in the ground clearance of the Lada 2110 and the possibility of increasing ground clearance using spacers.

To begin with, it’s worth honestly saying that the real ground clearance of the VAZ 2110 may differ significantly from that declared by the manufacturer. The whole secret is in the method of measuring and where to measure ground clearance. Therefore, you can find out the real state of affairs only by arming yourself with a tape measure or ruler. The official ground clearance of the VAZ 2110 is 160 mm when the car is loaded. In an empty car, you can easily measure 180 mm of clearance.

Some manufacturers use a trick and declare the amount of ground clearance in an “empty” car, but in real life we ​​have a trunk full of all kinds of things, passengers and a driver. That is, in a loaded car the ground clearance will be completely different. Avtovaz is honest in this regard. Another factor that few people take into account is the age of the car and the wear and tear of the springs—their “sagging” due to age. The issue can be resolved by installing new springs or purchasing spacers for sagging VAZ 2110 springs . Spacers allow you to compensate for spring subsidence and add a couple of centimeters of ground clearance. Sometimes even an inch of curb parking makes a difference.

But you shouldn’t get carried away with “lifting” the ground clearance of the VAZ 2110, because spacers to increase ground clearance are oriented only on springs. If you do not pay attention to the shock absorbers, the travel of which is often very limited, then independently upgrading the suspension can lead to loss of controllability and damage to the shock absorbers. From the point of view of cross-country ability, high ground clearance in our harsh conditions is good, but at high speeds on the highway and in corners, serious sway and additional body roll appear.

At the rear of the “ten”, so-called “houses” are traditionally used to increase ground clearance. Which simply lift the entire rack assembly. This method is suitable for almost all front-wheel drive Ladas. For an example, we suggest watching the video.

Any car manufacturer, when designing the suspension and choosing the ground clearance, looks for a middle ground between handling and cross-country ability. Perhaps the simplest, safest and most unpretentious way to increase clearance is to install wheels with “high” tires. Changing wheels makes it easy to increase the ground clearance by another centimeter. Do not forget that a serious change in ground clearance can lead to damage to the CV joints of the Lada 2110. After all, the “grenades” will have to work at a slightly different angle. But this only applies to the front axle.

Purpose

The front lights are called head lamps; they are located in the headlight unit in front of the car on both sides. They are the outermost ones in the lighting system, and owe their name to the fact that they show the width of the car to oncoming vehicles.

Various options for side lights and daytime running lights

The rear lights are intended for exactly the same mission—so that you can be seen by those driving behind you. This is especially true when overtaking; you don’t want someone to hit your “swallow” without seeing its real size.

Tuned tail lights

Hence the important advice: if it suddenly happens that you need to go at all costs and you discover that the light bulb in the left side light has burned out, replacing it with a new one is impossible due to the lack of one, don’t be lazy and move it from the right side. And we will tell you how to do this.

VAZ 2110 | Dimensions | Lada

Dimensions

Dimensions of two body options

Station wagon dimensions

Saloon, hatchback or station wagon (Turnier): Mondeo plays on the entire keyboard. In terms of width, measuring 1931 millimeters, there are no differences between them. The picture is different in terms of length - the maximum is 4804 millimeters for Turnier, in the other two versions it is 4731 millimeters. In terms of height, each model variant goes its own way: depending on the design of the chassis, the sedan body has a height in the range of 1420–1460 millimeters, the hatchback body, respectively, 1429–1459 millimeters and the Turnier – 1441–1471 millimeters. With a roof side rail, the height of the Turnier increases by another 40 millimeters. However, there is complete agreement on the wheelbase: 2754 millimeters is a good indicator for a high-middle class car. In addition, the Mondeo stands out for its large interior, which can accommodate five adult passengers.

Even in the rear seats, three medium-sized Europeans do not feel afraid of space. Mondeo passengers can also travel with more than just hand-luggage: the sedan and hatchback have a maximum volume of 500 liters, according to VDA standards – including a spare wheel. In Turnier, a loading volume of 540 liters is already available with a spare wheel. When the rear seat is folded down, the hatchback model will take 1,370 liters up to the roof, and the Turnier will swallow even 1,700 liters.

Let's make a small conclusion

This budget Ukrainian car on the secondary market costs up to two hundred thousand. An economical option for a first car to learn how to drive. It’s possible even for a student to save without loans. Easy to use. There are no difficulties in driving this car. Of course, there are many shortcomings, but again, in order to learn how to ride, it will do just fine. It can also serve well as a family car for retirees; compared to other cars, this car is quite economical. This is one of the most profitable cars in its class.