Standard oil filter for Priora: replacement instructions, manufacturers

The oil filter of a Priora car is responsible for cleaning the oil from impurities and metal particles. There are many filter manufacturers on Priora: Mann, Livny, Big, Salute and others. The price of an oil filter starts from 200 rubles - read the article to the end: you will find out popular filters, which one is better and the article numbers (original number) for them. All the oil in the engine flows through the oil filter. Therefore, it is the most important element of the filtration system. It is located in the lower engine compartment. The degree of oil purification affects the operation of the engine compartment. The cleaning system element does not depend on the engine type (16 or 8 valves); the standard configuration may have several variations.

Dimensions of the original Priora oil filter - article number

Regardless of the type and characteristics of the engine, the factory version of the Lada Priora is equipped with one of two filter options.

Oil filter salute

Manufactures. The company has been producing filter system elements for VAZ cars since 1998. Among the advantages of the part is a bypass valve device. Thanks to this system, the part allows the oil substance to pass through it, even if it is completely clogged. Among the disadvantages is the low quality of filter paper. It often breaks.

The article number for the oil cleaning element is 2108/1012005/010. The price of the part is from 150 rubles.

Oil cleaner Lada

Releases. Car enthusiasts note the low quality of the part. Disadvantages - poor quality paper, oil leakage around the perimeter of the folding.

Part number – 2108/1012005/08. Price – from 150 rubles.

To replace a part, you need to know its dimensions in order to select an analogue.

Oil filter for Priora 8 and 16 valves

Regardless of whether the Lada Priora has an 8 or 16 valve engine, the car is equipped with the same oil filters. In the original configuration, filters from 2 manufacturers :

LADA 2108-1012005-08 – . Cost – from 160 rubles. Has a lot of negative reviews. The main disadvantages are oil leakage along the rolling contour and low quality filter paper.

JSC Avtoagregat is a large Russian manufacturer of filter elements for the automotive industry. It is a supplier of original filters for many manufacturers, including AvtoVAZ.

Salute 2108-1012005-010 – . Average price - from 160 rubles. It has an original bypass valve design, which ensures constant oil flow through the filter, even when the filter components are clogged. Reviews about this filter model are different. The main disadvantage is the poor quality of filter paper. It often breaks during operation. Also uneven placement of the filter element.

CJSC SALYUT-FILTER is a Russian enterprise that specializes in the production of automobile filters. Has been supplying oil filters to the assembly line for VAZ cars since 1997.

Oil filter LADA 2108-1012005-08

Oil filter Salyut 2108-1012005-010

Dimensions of the original oil filter Lada Priora

External diameter	Inner diameter	Bypass valve opening pressure	Thread
93 mm	62 mm	1.2 bar	3/4″-16UNF

When choosing an oil filter for LADA Priora, you should pay attention to the following substitutes:

BIG Filter GB-102M . Price – from 120 rub. Manufacturer: Russian company BIG Filter. A popular substitute among Lada Priora owners. According to customer reviews, the quality is above average. Among the shortcomings is a weak rubber sealing ring.
FRAM PH5822 Price – from 170 rub. Reviews about this filter model are both positive and negative. The main disadvantages are that the filter element has a small total area and is not dense enough.
Mann W914/2 Part price – from 170 rubles. High-quality foreign analogue for Priora. Customer reviews are only positive. It has good quality synthetic filter paper, as well as an opening pressure of the bypass valve of 1.2 bar.

Oil filter BIG Filter GB-102M

Oil filter FRAM PH5822

Oil filter Mann W914/2

Instructions for dismantling and replacing parts

To replace it, it is not necessary to contact a car service specialist. You can do the work yourself if you acquire the necessary tools and follow the sequence of activities.

What is required for dismantling and replacement

wrench or socket size 17;
workwear;
container for draining used oil;
new spare part;
screwdriver;
rags;
hammer;
lubricant;
oil.

Step-by-step instructions for replacing the oil filter of a domestic car

Use the lift. Place the car on the racks, secure it, and raise it to the desired height.
Wait until the engine has cooled to avoid burns.
Unscrew the figured bolt from the drain hole.
Then you need to drain the lubricating fluid from the engine compartment. In this case, it is necessary to comply with safety requirements.
The filter is unscrewed using a puller. Use a rag to clean the hole threads from dirt. Dismantle the filtration system element.
Before installing a new spare part, the rubber seal is lubricated with a special lubricant.
When installing a new part, make sure that it is in tight contact with the seal. Otherwise, engine oil will leak.
Check the lubricant level, make sure that there is enough lubricant in the crankcase of the engine compartment.
Start the engine and check for oil leaks. If you are sure that nothing is leaking, turn off the engine and wait until it cools down.
Once the engine compartment temperature has dropped, use a dipstick to measure the engine compartment temperature. If there is not enough quantity, add to the required level.

After replacing yourself, monitor the fluid level for 10-14 days.

The oil filter is the most important element of the filtration system. The performance of the engine compartment and its components depends on the quality of cleaning. Standard cleaning elements are not always of high quality. However, this is a spare part that must be changed periodically. The car owner’s task is to promptly replace the fluid and cleaning parts. For the Lada Priora car, there are analogues of domestic and foreign production, among them there are cheap, high-quality products. You can order a spare part in the online auto parts store. To do this you need to know its article number.

Each owner of AvtoVAZ models is able to independently replace both the fluid and the filter spare part - if they have the hands. To do this, it is enough to study the algorithm of actions and make sure that you have the necessary tools.

Instructions for dismantling and replacement

The procedure for replacing the oil filter on a Lada Priora is not difficult. Even a beginner can easily cope with such work. To make everything clear to you and not cause any difficulties, we will write out this manual point by point and explain everything in detail.

Sorry, there are no surveys available at this time.

What will you need?

Sometimes the MF on the Lada Priora can be very difficult to remove. This is due to the fact that the sealing element of the product sticks, which makes it almost impossible to dismantle it. If you have a special key for removing the MF, then it will be much easier for you to dismantle it. But what if there is no such key? What to do in such cases? Then you will need a screwdriver, prepare it in advance.

Phillips blade screwdriver

Phased change

First of all, you should drive your Lada Priora into a garage with a pit or on a lift. Place a container under the bottom, or rather under the engine oil drain hole, and unscrew the drain plug. Wait until the liquid is completely drained so that you can continue with further steps. This may take up to 40 minutes. When the consumables are completely drained, the drain hole can be closed and the waste liquid can be put aside. And remember that it is necessary to drain the MM on a hot engine. You need to be careful not to get burned, but on a cold engine all the “working out” will not work. It will be more viscous and part of it will in any case remain in the system or on the walls of the pipes. Warm up the engine to operating temperature, then proceed with replacement.
Actually, when all the liquid has been drained, we come to the most important thing - replacing the oil filter on the Lada Priora. Open the hood of your Priora and find the installation location of the MF - you need to dismantle it. You can try to unscrew it by hand - usually this does not cause any difficulties. It happens that the oil filter sticks to the working surface. If so, try using a removable key. If you don’t have such a key and there is nowhere to get it, then this is also not a problem - take a regular screwdriver and pierce the MF with it. Use it as a lever to turn the component counterclockwise.
If you succeeded, then we congratulate you - there are still some nuances left. Now proceed to install the new MF. Pour some engine fluid into it, no more than half, and oil the component's O-ring around the threads. This needs to be done so that later you do not have problems with dismantling the MF when you subsequently replace the fluid. In addition, this is required so that the element does not stick to the working surface. In any case, when installing the MF, you need to lubricate it, because if you put a dry filter into operation and all its internal components are not lubricated, due to the high pressure in the system, the filter element itself may simply fail. And it will not be possible to detect this. Wait a few minutes for the liquid to completely saturate the working element. Install the new MF into the installation location by turning it clockwise. Screw it all the way, but do not use a wrench, since the MF must be installed in such a way that it can be removed by hand.
Next, go to the hood and find the cover for filling the consumables on the cylinder head. Open it and fill the Priora engine with as much fluid as is necessary for the normal functioning of the vehicle. From time to time you should check the level of the filled MM using a dipstick. When you have completely filled the required volume, wait about five minutes until all the liquid has completely drained into the crankcase. This must be done in order to obtain more accurate data on the level of the filled consumables. By the way, the fluid should be approximately halfway between the MIN and MAX marks on the dipstick.
When the MM filling procedure is completed, warm up the car to operating temperature. Let it idle for about ten minutes. After this, open the hood again and check the MM level. If necessary, add.

The request returned an empty result.

The MF that you install on your car must be of high quality and durable - check the element body before purchasing.

Remember that by installing low-quality parts on your car, you are subjecting the car to new tests. All elements must be of high quality and durable so that their service life is longer. As you may have noticed, this process is quite simple and not labor intensive. Follow all the recommendations above and you will succeed. Good luck!

Oil filter for Lada Priora

Important properties of a car oil filter include participation in the engine cooling process, as well as reducing noise during operation of the vehicle's piston group. To make a choice, you must have a firm understanding of its purpose for the vehicle.

When choosing a filter element, you should know that 2 types of oil filters are offered for sale on Priora: a prefabricated monolithic element and a replaceable filter insert in a single housing.

The first type of product is a cylindrical part in the shape of a glass, in the inner cavity of which there is a special corrugated cardboard that cleans the motor lubricant. The second type of oil filter in the form of a corrugated cardboard “accordion” ensures the passage of purified oil into the vehicle’s engine system.

In determining which oil filter will be Priora, it is necessary to give preference to filter elements of the second type. This is primarily due to its low price, its high environmental friendliness and quick replacement if necessary. However, many products, due to their simple design and low cost of the ingredients used, have become easy prey for manufacturers of counterfeit products, which have flooded the entire Russian automotive market.

To make the right choice, you should select spare parts from well-known brands Mann or Knecht. In addition, recently, instead of the standard oil filter on the Lada Priora of the Mann W914/2 type, they have been offering a new product - a product from the BOSCH P2044 company, which is externally elongated and has a smaller diameter. At the same time, it has an increased filter surface area and better performance test parameters.

Replacing the oil filter

You can replace the oil filter on a Priora on your own, without involving specialists; there is nothing complicated there. You just need to have plumbing skills and have the necessary tools:

Before replacing the oil filter, it is necessary to prepare the following units, tools and accessories: an electric lift, a set of plumbing tools, a free waste reservoir, an updated oil filter and rags.
Then we install the vehicle on supports using an electric lift.
Having cooled the power plant beforehand, so as not to get burned, we drain the waste from the engine crankcase by unscrewing the figured bolt from the drain hole.
We drain the engine lubricant in compliance with safety regulations, unscrew the oil filter and wipe the mounting area of the product with a rag.
Before installing the updated oil filter, the gasket rubber of the product is lubricated with a thin layer of lubricant. When installing the filter element, you must make sure that the part fits tightly against the gasket to prevent oil leakage through this connection.
Let’s put aside the work and the set of tools involved. When removing the car from an electric lift, it is necessary to bring the lubricant in the engine crankcase to the required value.
We turn on the engine unit and test the vehicle for a possible oil leak at the place where the oil filter was replaced, after which we turn off the “engine” and wait for it to cool.
After waiting for the engine temperature to drop, we measure the lubricant level in the crankcase using an oil dipstick. If the indicator is insufficient, add the required amount of oil.
After replacing the filter on the Priora, monitor the lubricant level in the power plant for 2-3 weeks.

The filter replacement procedure must be carried out every time the oil is changed after the end of its service life.

Replacing the filter

Removing the old oil filter and installing a new one is a process that even a beginner can handle. But in some cases, when the seal gets stuck, it takes a lot of effort to replace it. If you have a special key for removing the filter, then there will be no problems. But if it is not there, you need to prepare a powerful screwdriver in advance.

In order to change the oil filter on the Lada Priora, you need to drive it into an inspection hole or onto a lift. Place a container under the engine oil drain hole to drain the fluid. Unscrew the plug and wait until the oil completely flows into the container. When the liquid has completely drained, the plug can be returned to its place, and the container with it can be put aside. The oil must be drained when the engine is hot, so extreme care must be taken. Next, warm up the engine to operating temperature and you can begin replacing the oil filter.

After this, you need to open the hood and find the installation location of the old filter. When the engine is warm, you can try to unscrew it by hand, this often does not cause any difficulties. But in most cases, the filter sticks to the working surface, and you can’t do it without the help of a special wrench. If there is none, carefully punch a hole in the side, and then, using a powerful screwdriver, unscrew the filter counterclockwise.

After successful dismantling, you can proceed to the next stage. Before installation, thoroughly lubricate the seat with oil and fill the new filter halfway. This is necessary so that during the next replacement there will be no problems with dismantling. This procedure will also avoid failure of the filter element, since the oil filter will not be dry when starting the engine. After filling, wait a few minutes until the entire inside of the oil filter is saturated with liquid.

How to change the engine oil filter

Replacing an old filter device with a new one in relation to a Priora car is carried out simultaneously with changing the oil fluid in the engine. AvtoVAZ recommends changing synthetic lubricant every 15 thousand kilometers. If the car is operated in difficult urban conditions, this procedure should be carried out more often - every 10 thousand km. In order to carry out this work, you must first prepare:

synthetic motor oil with a volume of at least 3.5 liters;
a new oil filter from those listed above;
a container for draining spent fluid with a capacity of at least 4 liters;
wrench 17, filter removal device;
rags and wire brush.

Before replacing, warm up the engine well to operating temperature. It is advisable to fill in the same lubricant as was used before. If you want to fill in a different brand of lubricant from a different manufacturer, after draining the used one, you need to rinse the motor with a special flushing oil. In this case, it is advisable to change the filtration device 2 times - before washing and before adding fresh oil.

Lada Priora is placed above the inspection hole or drives onto an overpass.
The hood opens, the neck is unscrewed, through which lubricant is poured.
The engine splash guard is removed, cleaned with a brush and a rag, and then the drain plug is loosened.
An empty container is placed under the cork, and the cork is carefully unscrewed.
The spent fluid is drained from the engine. You should wait until the leak stops.
The plug is screwed into place.
The container is installed under the filter to prevent lubricant from spilling from it. It is unscrewed with a special device.
Fresh oil is poured into the new filter device to 2/3 of its volume.
The O-ring is also lubricated with clean oil.
The new filtration device is screwed in by hand. As soon as the seal touches the motor housing, you should tighten the filter by hand 3/4 of a turn.
Fresh lubricant is poured through the neck under the hood. Its level is checked with a dipstick. It should be around the max.
Start the engine, check the lubricant pressure level using the emergency indicator - it should go out 2-3 seconds after the start.
After the engine has been running for several minutes, the lubricant level is measured again. The norm is in the middle between the min and max marks. If below, oil should be added.

It is necessary to check for any grease leaks in the area of the filter and drain hole. If there is, you need to tighten these elements. This completes the work.

Original filter Lada Priora: articles, price

Serial number	Price in rubles
Mann H90W03	H10W13	Mann H90W13	From 340 – 370
Mann H90W65	Mann H90W45	Mann H90W27	From 340 – 370
*prices are as of July 2021